当前位置:首页 >> 信息与通信 >>

北电BayStack.460


Part No. 217108-A June 2005 4655 Great America Parkway Santa Clara, CA 95054

Installing the Nortel Ethernet Switch 470

*217108-A*

2

Copyright ? No

rtel Networks Limited 2005. All rights reserved.
The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks NA Inc. The software described in this document is furnished under a license agreement and may be used only in accordance with the terms of that license. The software license agreement is included in this document.

Trademarks
Autotopology, BayStack, BaySecure, Business Policy Switch 2000, Nortel Networks, the Nortel Networks logo, Optivity, Optivity Policy Services, Preside, and Quick2Config are trademarks of Nortel Networks. Microsoft, MS, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Java is a trademark of Sun Microsystems, Inc. Acrobat and Adobe are trademarks of Adobe Systems, Inc. All other trademarks and registered trademarks are the property of their respective owners.

Restricted rights legend
Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013. Notwithstanding any other license agreement that may pertain to, or accompany the delivery of, this computer software, the rights of the United States Government regarding its use, reproduction, and disclosure are as set forth in the Commercial Computer Software-Restricted Rights clause at FAR 52.227-19.

Statement of conditions
In the interest of improving internal design, operational function, and/or reliability, Nortel Networks Inc. reserves the right to make changes to the products described in this document without notice. Nortel Networks Inc. does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Portions of the code in this software product may be Copyright ? 1988, Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms of such portions are permitted, provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation, advertising materials, and other materials related to such distribution and use acknowledge that such portions of the software were developed by the University of California, Berkeley. The name of the University may not be used to endorse or promote products derived from such portions of the software without specific prior written permission. SUCH PORTIONS OF THE SOFTWARE ARE PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. In addition, the program and information contained herein are licensed only pursuant to a license agreement that contains restrictions on use and disclosure (that may incorporate by reference certain limitations and notices imposed by third parties).

217108-A

3

International regulatory statements of conformity
This is to certify that the Nortel Ethernet Switches 460 and 470 were evaluated to the international regulatory standards for electromagnetic compliance (EMC) and safety and were found to have met the requirements for the following international standards: ? ? ? EMC - Electromagnetic Emissions – CISPR 22, Class A EMC - Electromagnetic Immunity – CISPR 24 Electrical Safety – IEC 60950, with CB member national deviations

Further, the equipment has been certified as compliant with the national standards as detailed below.

National electromagnetic compliance (EMC) statements of compliance
FCC statement (USA only)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense.

ICES statement (Canada only)
Canadian Department of Communications Radio Interference Regulations This digital apparatus (Nortel Ethernet Switches 460 and 470) do not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Règlement sur le brouillage radioélectrique du ministère des Communications Cet appareil numérique (Nortel Ethernet Switches 460 and 470) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.

CE marking statement (Europe only)
EN 55 022 statements This is to certify that the Nortel Ethernet Switches 460 and 470 are shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC. Conformity is declared by the application of EN 55 022 Class A (CISPR 22).

Caution: This device is a Class A product. In a domestic environment, this device can cause radio interference, in which case the user may be required to take appropriate measures.

Installing the Nortel Ethernet Switch 470

4
EN 55 024 statement This is to certify that the Nortel Ethernet Switches 460 and 470 are shielded against the susceptibility to radio interference in accordance with the application of Council Directive 89/336/EEC. Conformity is declared by the application of EN 55 024 (CISPR 24). CE Declaration of Conformity This product conforms to the provisions of the R&TTE Directive 1999/5/EC.

VCCI statement (Japan/Nippon only)
This is a Class A product based on the standard of the Voluntary Control Council for Interference (VCCI) for information technology equipment. If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

BSMI statement for Ethernet Switches 460 and 470 (Taiwan only)
This is a Class A product based on the standard of the Bureau of Standards, Metrology and Inspection (BSMI) CNS 13438, Class A.

MIC notice for Ethernet Switches 460 and 470 (Republic of Korea only)
This device has been approved for use in Business applications only per the Class A requirements of the Republic of Korea Ministry of Information and Communications (MIC). This device may not be sold for use in a non-business application. Observe the Regulatory Marking label on the bottom surface of the chassis for specific certification information pertaining to this model. Each model in the Ethernet Switch Series which is approved for shipment to/usage in Korea is labeled as such, with all appropriate text and the appropriate MIC reference number.

217108-A

5

National safety statements of compliance
CE marking statement (Europe only)
EN 60 950 statement This is to certify that the Nortel Ethernet Switches 460 and 470 are in compliance with the requirements of EN 60 950 in accordance with the Low Voltage Directive. Additional national differences for all European Union countries have been evaluated for compliance.

NOM statement Ethernet Switches 460 and 470 (Mexico only)
The following information is provided on the devices described in this document in compliance with the safety requirements of the Norma Oficial Méxicana (NOM): Exporter: Nortel Networks, Inc. 4655 Great America Parkway Santa Clara CA 95054 USA Nortel Networks de México, S.A. de C.V. Avenida Insurgentes Sur #1605 Piso 30, Oficina Col. San Jose Insurgentes Deleg-Benito Juarez México D.F. 03900 52 5 480 2100 52 5 480 2199 Ethernet Switch 460, Ethernet Switch 470 100 - 120 VAC 16A 50 to 60 Hz 200 - 240 VAC 12 A 50 to 60 Hz

Importer:

Tel: Fax: Input:

Información NOM (unicamente para México)
La información siguiente se proporciona en el dispositivo o en los dispositivos descritos en este documento, en cumplimiento con los requisitos de la Norma Oficial Méxicana (NOM): Exportador: Nortel Networks, Inc. 4655 Great America Parkway Santa Clara, CA 95054 USA Nortel Networks de México, S.A. de C.V. Avenida Insurgentes Sur #1605 Piso 30, Oficina Col. San Jose Insurgentes Deleg-Benito Juarez México D.F. 03900 52 5 480 2100 52 5 480 2199 Ethernet Switch 460, Ethernet Switch 470 100 - 120 VAC 16A 50 to 60 Hz 200 - 240 VAC 12 A 50 to 60 Hz

Importador:

Tel: Fax: Embarcar a:

Installing the Nortel Ethernet Switch 470

6

Nortel Networks Inc. software license agreement
This Software License Agreement (“License Agreement”) is between you, the end-user (“Customer”) and Nortel Networks Corporation and its subsidiaries and affiliates (“Nortel Networks”). PLEASE READ THE FOLLOWING CAREFULLY. YOU MUST ACCEPT THESE LICENSE TERMS IN ORDER TO DOWNLOAD AND/OR USE THE SOFTWARE. USE OF THE SOFTWARE CONSTITUTES YOUR ACCEPTANCE OF THIS LICENSE AGREEMENT. If you do not accept these terms and conditions, return the Software, unused and in the original shipping container, within 30 days of purchase to obtain a credit for the full purchase price. “Software” is owned or licensed by Nortel Networks, its parent or one of its subsidiaries or affiliates, and is copyrighted and licensed, not sold. Software consists of machine-readable instructions, its components, data, audio-visual content (such as images, text, recordings or pictures) and related licensed materials including all whole or partial copies. Nortel Networks grants you a license to use the Software only in the country where you acquired the Software. You obtain no rights other than those granted to you under this License Agreement. You are responsible for the selection of the Software and for the installation of, use of, and results obtained from the Software. 1. Licensed Use of Software. Nortel Networks grants Customer a nonexclusive license to use a copy of the Software on only one machine at any one time or to the extent of the activation or authorized usage level, whichever is applicable. To the extent Software is furnished for use with designated hardware or Customer furnished equipment (“CFE”), Customer is granted a nonexclusive license to use Software only on such hardware or CFE, as applicable. Software contains trade secrets and Customer agrees to treat Software as confidential information using the same care and discretion Customer uses with its own similar information that it does not wish to disclose, publish or disseminate. Customer will ensure that anyone who uses the Software does so only in compliance with the terms of this Agreement. Customer shall not a) use, copy, modify, transfer or distribute the Software except as expressly authorized; b) reverse assemble, reverse compile, reverse engineer or otherwise translate the Software; c) create derivative works or modifications unless expressly authorized; or d) sublicense, rent or lease the Software. Licensors of intellectual property to Nortel Networks are beneficiaries of this provision. Upon termination or breach of the license by Customer or in the event designated hardware or CFE is no longer in use, Customer will promptly return the Software to Nortel Networks or certify its destruction. Nortel Networks may audit by remote polling or other reasonable means to determine Customer’s Software activation or usage levels. If suppliers of third party software included in Software require Nortel Networks to include additional or different terms, Customer agrees to abide by such terms provided by Nortel Networks with respect to such third party software. Warranty. Except as may be otherwise expressly agreed to in writing between Nortel Networks and Customer, Software is provided “AS IS” without any warranties (conditions) of any kind. NORTEL NETWORKS DISCLAIMS ALL WARRANTIES (CONDITIONS) FOR THE SOFTWARE, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABLITITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY WARRANTY OF NON-INFRINGEMENT. Nortel Networks is not obligated to provide support of any kind for the Software. Some jurisdictions do not allow exclusion of implied warranties, and, in such event, the above exclusions may not apply. Limitation of Remedies. IN NO EVENT SHALL NORTEL NETWORKS OR ITS AGENTS OR SUPPLIERS BE LIABLE FOR ANY OF THE FOLLOWING: a) DAMAGES BASED ON ANY THIRD PARTY CLAIM; b) LOSS OF, OR DAMAGE TO, CUSTOMER’S RECORDS, FILES OR DATA; OR c) DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), WHETHER IN CONTRACT, TORT OR OTHERWISE (INCLUDING NEGLIGENCE) ARISING OUT OF YOUR USE OF THE SOFTWARE, EVEN IF NORTEL NETWORKS, ITS AGENTS OR SUPPLIERS HAVE BEEN ADVISED OF THEIR POSSIBILITY. The forgoing limitations of remedies also apply to any developer and/or supplier of the Software. Such developer and/or supplier is an intended beneficiary of this Section. Some jurisdictions do not allow these limitations or exclusions and, in such event, they may not apply. General a. If Customer is the United States Government, the following paragraph shall apply: All Nortel Networks Software available under this License Agreement is commercial computer software and commercial computer software documentation and, in the event Software is licensed for or on behalf of the United States Government,

2.

3.

4.

217108-A

7
the respective rights to the software and software documentation are governed by Nortel Networks standard commercial license in accordance with U.S. Federal Regulations at 48 C.F.R. Sections 12.212 (for non-Odd entities) and 48 C.F.R. 227.7202 (for Odd entities). b. Customer may terminate the license at any time. Nortel Networks may terminate the license if Customer fails to comply with the terms and conditions of this license. In either event, upon termination, Customer must either return the Software to Nortel Networks or certify its destruction. c. Customer is responsible for payment of any taxes, including personal property taxes, resulting from Customer’s use of the Software. Customer agrees to comply with all applicable laws including all applicable export and import laws and regulations. d. Neither party may bring an action, regardless of form, more than two years after the cause of the action arose. e. The terms and conditions of this License Agreement form the complete and exclusive agreement between Customer and Nortel Networks. f. This License Agreement is governed by the laws of the country in which Customer acquires the Software. If the Software is acquired in the United States, then this License Agreement is governed by the laws of the state of New York.

Installing the Nortel Ethernet Switch 470

8

Revision History
Date Revised June 2005 Version 1.0 Reason for revision Created new document structure and incorporated new branding for Ethernet Switch Release 3.6 software.

217108-A

9

About this guide
This guide provides instructions to install the Nortel Ethernet Switch 470-24T and Nortel Ethernet Switch 470-48T on a table, in an equipment rack, or on a wall. For more detailed information about the switch, refer to the System Configuration Guide (217105-A). This guide includes information about the following topics: ? ? ? ? ? ? Environmental requirements for the installation site Installing the switch on a table (page 11) or in a rack (page 12) Network connection requirements (page 13) Connecting AC power (page 15) Descriptions of LEDs (page 17) Initial switch setup (page 19)

Before you begin
Ensure the area where you install and use the Ethernet Switch 470 meets the following environmental requirements: ? ? ? ? ? ? ? ? Ambient temperature between 32° and 104° F (0° and 40° C) Relative humidity between 5% and 85% noncondensing No nearby heat sources such as hot air vents or direct sunlight No nearby sources of severe electromagnetic noise No excessive dust Adequate power source within six feet; one 15-Amp circuit required for each power supply At least 2 inches (5.08 cm) on each side of the switch unit for ventilation Adequate space at the front and rear of the switch for access to cables

If you are installing a single Ethernet Switch 470 on a table or shelf, ensure the surface can support at least 15 to 20 pounds (7 to 9 kilograms).

Installing the Nortel Ethernet Switch 470

10

Package contents
Figure 1 shows the package contents that accompany each Ethernet Switch 470.
Figure 1 Package contents
2

3

1

4

5

10752FA

6

1 = Ethernet Switch 470 (Ethernet Switch 470-48T shown. Ethernet Switch 470-24T has the same appearance and requirements as the Ethernet Switch 48T, but with only 24 10/100 ports). 2 = Rack-mounting hardware: ? Rack-mount brackets ? Screws for attaching brackets to the switch ? Screws for attaching the switch to the equipment rack 3 = Rubber footpads 4 = AC power cord 5 = Documentation 6 = Stacking cable

217108-A

11

Installing the switch on a table or shelf
You can install a single Ethernet Switch 470 on any flat surface that can safely support the weight of the switch and attached cables (15 to 20 pounds or 7 to 9 kilograms). Figure 2 provides instructions on installing the switch on a table or shelf.
Figure 2 Installing switch on table or shelf

10753FB

10754FA

1

Attach the rubber feet at the marked locations.

2

Set the switch on a table or shelf.

Note: Allow at least 2 inches (5.1 cm) on each side for proper ventilation and at least 5 inches (12.7 cm) at the back for power cord clearance.

Caution: Do not set a Nortel Ethernet Switch Power Supply Unit 10 on top of an Ethernet Switch 470. The Power Supply Unit 10 weighs approximately 100 pounds (45 kg), and the switch housing is not strong enough to support this weight.

Installing the Nortel Ethernet Switch 470

12

Installing the switch in an equipment rack
Required tool: Phillips screwdriver for attaching brackets to the switch Rack requirements: ? ? ? A space of 2.8 inches is required for each switch in an EIA or IEC standard 19-inch (48.2-centimeter) equipment rack. The rack must be bolted to the floor and braced, if necessary. The rack must be grounded to the same grounding electrode used by the power service in the area. The ground path must be permanent and must not exceed 1 ohm of resistance from the rack to the grounding electrode.

Figure 3 provides instructions on installing the switch in a rack.
Figure 3 Installing switch in a rack

10755FA
10756FA

1

Attach a bracket to each side of the switch.

2

Slide the switch into the rack. Insert and tighten the rack-mount screws.

Caution: Do not set a Nortel Ethernet Switch Power Supply Unit 10 on top of an Ethernet Switch 470. The Power Supply Unit 10 weighs approximately 100 pounds (45 kg), and the switch housing is not strong enough to support this weight.

217108-A

13

Installing Stacking Cables
Note: The stacking cables can be installed very quickly and simply. However, do not install stacking cables on an Ethernet Switch 470 that does not have at least v2.2 software loaded. Similarly, set the Unit Select switch in the Off (down = Off) position on ALL units running v2.1 software. Please refer to the System Configuration Guide (217105-A) for a complete description of cable installation and other important information about stacking of Ethernet Switches 470. Go to www.nortel.com/support to see this guide.

Connection requirements
Table 1 describes the data cable requirements for the Ethernet Switch 470.
Table 1 Cable requirements
Required cables: 10/100BASE-T ports Console Port GBIC ports For 10 Mb/s operation: Category 3, 4, or 5 UTP cable with an RJ-45 connector For 100 Mb/s operation: Category 5 UTP cable with an RJ-45 connector Serial cable with DB-9 female connector. Varies with the installed GBIC; refer to the documentation that was shipped with the GBIC for specifications.

Installing the Nortel Ethernet Switch 470

14

Table 2 describes the pin assignments in the console port connector.
Table 2 Pin assignments in the port
Connector
1 5

Pin number 1 2 3 4

Signal Carrier detect (not used) Transmit data (TXD) Receive data (RXD) Data terminal ready (not used) Signal ground (GND) Not used Request to send (not used) Not used Ring indicator (not used)

6

9
9473EA

5 6 7 8 9

217108-A

15

Connecting AC power
Required cable: AC power cord that meets the requirements of your local electrical code. Refer to Table 3 for plug specifications.
Table 3 International power cord specifications
Country/plug description Continental Europe: ? CEE7 standard VII male plug ? Harmonized cord (HAR marking on the outside of the cord jacket to comply with the CENELEC Harmonized Document HD-21) U.S./Canada/Japan: ? NEMA5-15P male plug ? UL-recognized (UL stamped on cord jacket) ? CSA-certified (CSA label secured to the cord) United Kingdom: ? BS1363 male plug with fuse ? Harmonized cord Specifications 220 or 230 VAC 50 Hz Single phase
228FA

Typical plug

100 or 120 VAC 50-60 Hz Single phase
227FA

240 VAC 50 Hz Single phase

229FA

Australia: ? AS3112-1981 male plug

240 VAC 50 Hz Single phase

230FA

Danger: Use only power cords that have a grounding path. Without a proper ground, a person who touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to the switch can result in excessive emissions.

Installing the Nortel Ethernet Switch 470

16

The Ethernet Switch 470 does not have a power switch. When you connect the AC power cord to a suitable AC power outlet, the switch powers up immediately. Figure 4 shows how to connect the AC power cable to the Ethernet Switch 470.
Figure 4 Connecting the AC power cord

100-240V~ 50-60Hz 1.5A

10763FB

Connect the AC power cord to the back of the switch, and then connect the cord to a power outlet. Warning: Disconnecting the power cord is the only way to turn off power to this device. Always connect the power cord in a location that can be reached quickly and safely in case of an emergency.

AC Power specifications
Table 4 describes the AC Power specifications for the Ethernet Switch 470.
Table 4 AC Power specifications
Input current: Input voltage (rms): Power consumption: Thermal rating: Maximum 1.5 A 100 to 240 VAC at 50 to 60 Hz 90 W 324 BTU/hr. maximum

217108-A

17

Checking LEDs
Figure 5, Table 5, and Table 6 on page 18 provide descriptions of the LEDs on the Ethernet Switch 470. The tables describe LED operations for a switch that has completed its power-on self-tests.
Figure 5 Ethernet Switch 470 LEDs
Top Row LEDs Bottom Row LEDs

47

LED Status 1

Amber:10 Mbp Green:100 Mbp

3

3
Link Pwr Up Status Down RPSU Base Act 2 4 48 Act Link

1

2
10764EA

1 = Switch LEDs 2 = GBIC Port LEDs 3 = 10/100 Port LEDs

Table 5 Switch LEDs on the Ethernet Switch 470
Label Pwr Color/Status Green/steady Off Status Green/steady Green/blinking Off RPSU Green/steady Off Meaning Power is available to the switch internal circuitry. There is no power to the switch, or the power supply has failed. The power-on self test is complete, and the switch is operating normally. A nonfatal error occurred during the self-test. The switch failed the self-test. The switch is connected to an RPSU (redundant power supply unit) and can receive power if necessary. The switch is not connected to an RPSU, or the RPSU is not supplying power.

Installing the Nortel Ethernet Switch 470

18 Table 5 Switch LEDs on the Ethernet Switch 470 (continued)
Label Up Color/Status Green/steady Amber/steady Meaning The switch is connected to the Down connector on the upstream unit. This unit has detected a problem with the switch connected to the Up connector. To maintain the integrity of the stack, this unit has bypassed its upstream neighbor and has wrapped the stack backplane onto an alternate path.

Green or amber/ The software version on this unit is incompatible or the software cannot blinking obtain a unit ID because the Renumber Stack Unit table is full. This unit is on the stack ring but cannot participate in the stack configuration. Off Dwn Green/steady Amber/steady The switch is in stand-alone mode. The switch is connected to the Up connector on the downstream unit. This unit has detected a problem with the switch connected to the Down connector. To maintain the integrity of the stack, this unit has bypassed its downstream neighbor and has wrapped the stack backplane onto an alternate path.

Green or amber/ The software version is incompatible or is unable to obtain a unit ID because blinking the Renumber Stack Unit table is full. This unit is on the stack ring but is unable to participate in the stack configuration. Off Base Green/steady Green/blinking Amber Off The switch is in stand-alone mode. This switch is the stack base unit. There is a stack configuration error. Either multiple base units or no base units are configured in the stack. This unit is operating as the temporary base unit in the stack configuration. This switch is not the stack base unit, or it is operating in stand-alone mode.

Table 6 Port LEDs on the Ethernet Switch 470
Label 10/100 Color/Status Green/steady Green blinking Amber/steady Amber/blinking Off Activity Green/blinking Off Meaning This port is set to operate at 100 Mb/s, and the link is good. This port has been disabled by software. This port is set to operate at 10 Mb/s, and the link is good. This port has been disabled by software. The link is bad, or nothing is connected to this port. There is activity on this port. There is no activity on this port.

217108-A

19

Initial switch setup
The Ethernet Switch 470 begins switching as soon as you attach network devices and connect the switch to power. To manage the switch using Telnet or SNMP or to perform TFTP operations, you must set certain IP parameters. In addition, if you are connecting Ethernet Switches 470 into a stack configuration, you must supply additional parameters to properly set up the stack. Refer to the System Configuration Guide (217105-A) for more information about the console menus and configuring your Ethernet Switch 470.

Setting IP parameters
For the initial setup of a stand-alone switch or a stack configuration, you must set the following IP parameters: ? ? ? IP address of the switch or the stack Subnet mask Gateway address

To set the IP parameters: 1 2 3 4 Connect a terminal to the Console port on the switch. Set the terminal protocol as described in the System Configuration Guide (217105-A). Connect the switch to a power outlet. After the Nortel logo is displayed, press [Ctrl]-Y to display the Main Menu. The Console Interface first displays the Main Menu for a stand-alone switch (see Figure 6 on page 20). Then, if the switch is part of a stack configuration, the screen is refreshed within 20 seconds to show the Main Menu for a stack configuration. The Main Menu for a stack configuration includes stack features (in bold text in Figure 6 on page 20).

Installing the Nortel Ethernet Switch 470

20 Figure 6 Ethernet Switch Console Interface main menu
Ethernet Switch 470-48T Main Menu IP Configuration/Setup... SNMP Configuration... System Characteristics... Switch Configuration... Console/Comm Port Configuration... Identify Unit Numbers... Renumber Stack Units... Display Hardware Units... Spanning Tree Configuration... TELNET/SNMP/Web Access Configuration... Software Download... Configuration File... Display System Log Reset Reset to Default Settings Shutdown Command... Command Line Interface... Logout Use arrow keys to highlight option, press <Return> or <Enter> to select option. Press Ctrl-R to return to previous menu. Press Ctrl-C to return to Main Menu.

5

Select IP Configuration/Setup (or press i) to display the IP Configuration/Setup menu (see Figure 7 on page 21). Note: The default management VLAN in the Ethernet Switch 470 is VLAN 1. To manage the switch, ensure the network management station is on the management VLAN or is connected to the management VLAN through routers.

217108-A

21 Figure 7 IP Configuration/Setup screen

IP Configuration/Setup BootP Request Mode: [ BootP When Needed In Use --------------0.0.0.0 192.168.249.49 255.255.255.0 192.168.249.1 ] Last BootP -------------0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0

Configurable ------------------In-Band Stack IP Address: [ 0.0.0.0 ] In-Band Switch IP Address: [ 192.168.249.49 ] In-Band Subnet Mask: [ 255.255.255.0 ] Default Gateway: IP Address to Ping: Start Ping: [ 192.168.249.1 ] [ 192.168.249.23 ] [ No ]

Use space bar to display choices, press <Return> or <Enter> to select choice. Press Ctrl-R to return to previous menu. Press Ctrl-C to return to Main Menu.

6

For a stand-alone switch, in the In-Band Switch IP Address field, enter the IP address of the switch in dotted-decimal notation. Note: If the In-Band Subnet Mask field does not already contain a value when you enter the IP address in the In-Band IP Address field, the switch software provides an in-use default value for the In-Band Subnet Mask field. This value is based on the class of the entered IP address.

7

For a stack configuration, in the In-Band Stack IP Address field, enter the Stack IP address in dotted decimal notation. Note: The In-Band Switch IP Address field allows this switch to operate as a stand-alone switch. However, this field is not required for the operation of the stack. You cannot enter the same IP address in both fields.

8 9

In the In-Band Subnet Mask field, enter the IP subnet mask address. In the Default Gateway field, enter the default gateway address.

Installing the Nortel Ethernet Switch 470

22

Related publications
You can print selected technical manuals and release notes free, directly from the Internet. Go to www.nortel.com/support. Find the product for which you need documentation. Then locate the specific category and model or version for your hardware or software product. Use Adobe* Acrobat Reader* to open the manuals and release notes, search for the sections you need, and print them on most standard printers. Go to Adobe Systems at www.adobe.com to download a free copy of the Adobe Acrobat Reader. For more information about using the Ethernet Switch 470, refer to the following publications: ? Release Notes for the Ethernet Switch 460 and 470 Switch Software Version 3.6 (217103) Documents important changes about the software and hardware that are not covered in other related publications. ? System Configuration Guide (217105-A) Describes how to configure and manage basic switching features on Ethernet Switches 460 and 470. ? Configuring and managing Security (217104-A) Describes how to configure and manage security features on Ethernet Switches 460 and 470. ? Configuring VLANs, Spanning Tree, and Multilink Trunking (217460-A) Describes how to configure and manage Virtual Local Area Network (VLAN), Spanning Tree Protocol (STP), and Multilink Trunk (MLT) features on Ethernet Switches 460 and 470. ? Configuring Quality of Service, and IP Filtering (217106-A) Describes how to configure and manage Quality of Service and IP Filtering features on Ethernet Switches 460 and 470. ? System Monitoring Guide (217107-A) Describes how to display system statistics, configure system logging, and configure network monitoring on Ethernet Switches 460 and 470. ? Configuring IP Multicast Routing Protocols (217459-A) Describes how to configure and manage IP Multicast and IGMP features on Ethernet Switches 460 and 470.

217108-A

23

?

Installing Gigabit Interface Converters, SFP, and CWDM SFP Gigabit Interface Converters (part number 312865-C) Describes how to install optional GBICs, SFP GBICs, and CWDM SFP GBICs in the Ethernet Switches 460 and 470.

?

BayStack 10 Power Supply Unit Installation Instructions (part number 208558-B) Describes installation, power-up, power-down, and fan replacement procedures for the Nortel Ethernet Switch Power Supply Unit 10.

?

Release Notes for the BayStack 10 Power Supply Unit (part number 208560-B) Documents important changes about the RPSU/UPS that are not covered in other related publications.

?

Installation and Reference for the BayStack RPSU/UPS (part number 208296-C) Describes how to install the optional RPSU/UPS on the Nortel Ethernet Switch Power Supply Unit 10 for the Ethernet Switches 460 and 470 and the OM 1450 ESM module.

How to get help
If you purchased a service contract for your Nortel product from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller for assistance. If you purchased a Nortel service program, contact one of the following Nortel Networks Technical Solutions Centers:
Technical Solutions Center Europe, Middle East, and Africa North America Asia Pacific China Telephone (33) (4) 92-966-968 (800) 4NORTEL or (800) 466-7835 (61) (2) 9927-8800 (800) 810-5000

Additional information about the Nortel Technical Solutions Centers is available from www.nortel.com/callus. An Express Routing Code (ERC) is available for many Nortel products and services. When you use an ERC, your call is routed to a technical support person who specializes in supporting that product or service. To locate an ERC for your product or service, go to www.nortel.com/erc.
Installing the Nortel Ethernet Switch 470

24

217108-A


相关文章:
北电 420配置信息
460页 2财富值 北电4500、5500系列常用配... 28页 1财富值喜欢...北电420配置信息北电420配置信息隐藏>> 实验一 BAYSTACK420 基本配置过程 一、 ...
北电实训教材
1.7 实验 7:北电网络二级交换机的基本配置—— Baystack 420/425 实验目的:了解掌握北电接入层交换机的基本配置方式,包括命令行 CLI 方式和 图形化工具 DM(...
Baystack 5510采购规范
北电BayStack.460_470技... 32页 免费 采购规范 3页 1下载券 北电BayStack...BayStack BayStack 5510 採購規範具備 24port MDI/MDIX 10/100/1000 BaseTX ...
北电交换机调试例子
我们公司的北电交换机主要用到了 2 个技术, 一 个是交换机堆叠,另外就是端口的聚合。我们用的北 电交换机型号为 baystack 450-24t,如下图所示: 先来看以下...
kf ja ffk a
北电BayStack.460_470技... 310页 免费 Kalmatron_KF-A 暂无评价 26页 1下载券 (2) Derivation for [A... 2页 免费 Jasmonic Acid (JA) Act... 暂无...
故障处理手册
6.北电baystack470-48 故障现象:这台交换机启动不了,重启连自检都过不了。 处理步骤:用串口连上电脑,在重启时按住 ctrl+c 键会出现一个菜单 点击相应的...
文档 4
楼层桌面接入 在桌面接入层,采用北电网络高性能的可堆叠桌面交换机 BayStack450提供每个 桌面用户10/100M 独享的以太网端口。 设备配置如下: Bay Stack 450-24T ...
8K与420的连接
北电配置北电配置隐藏>> 实验三、 实验三、Passport8100 和 Baystack420 的互连在一般情况下如果我们想实验三个 Vlan 都是上联到上级交换机上,我们 必须如下操作...
BayStack 420的配置
关键词:北电420 1/2 相关文档推荐 北电Baystack交换机460-47... 暂无评价 132...配置选项如下图所示:In-Band Stack IP Address:选项配置堆叠后北京艾因泰克科技...
420和8100
北电420配置信息 17页 1下载券 交岔点 26页 免费 万用英语口语句典_目录 25...24 2 一、 Baystack 420 交换机的调试: Baystack420 是 NortelNetwork 的...
更多相关标签:
baystack | 关晓彤北电报到 | 北电网络公司 | 北京北电影视艺术学院 | 中戏北电那些事 | 北电网络 | 尤浩然考上北电了吗 | 北电校花 |