当前位置:首页 >> 机械/仪表 >>

固井泵 哈里伯顿HT-400 pump


Cementing

HT-400? Pump
The Industry Standard

Halliburton’s HT-400? Pump is a lightweight, rugged,
versatile unit that was introduced in 1957. Its name denotes

Horizontal Triplex and its original rating of 400 horsepower. Since its debut, the basic design has been improved and upgraded until it now is rated at 800 hp maximum in some configurations. The pump has performed millions of operating hours in fracturing, acidizing, cementing, and sand and water control work.

Features
The Halliburton twin-pump or flexibility concept is particularly useful when precise pumping ranges and controls are required. Halliburton exclusively manufactured the HT-400 pump power end, so that practically all parts are interchangeable. The exception is that the power end case is built in both left- and right-hand configurations. Internal parts, including the proven worm/ring gear sets, are identical, only the case is different. Power ends can be fitted with any of the five sizes of fluid ends – 3 3/8”, 4”, 4 ?”, 5” and 6” plungers – each with characteristics suitable for specific applications. Power end components: ? Case and Drive Gears: Power End cases are manufactured exclusively by Halliburton in both leftand right-hand models. They are made of highstrength weldments of Halliburton design. They are not interchangeable. ? Crankshaft: Heat-treated steel forgings are used to manufacture crankshafts. All cranks are the same, even for left- and right-hand units. ? Connecting Rods: Connecting rods are made from aluminum forgings. The identical rods are internally drilled to provide lubrication to the crosshead pins. ? Crossheads: Crosshead bodies are made of heat-treated steel alloy castings. They are fitted with replaceable, highleaded bronze shoes on both top and bottom. ? Lubrication: Standard self-contained power end lubrication system is pressurized by an internal crescent gear-type pump driven off the end of the worm gear. Positive pressure lubrication is supplied to the crosshead slides, gear support bearings, crankshaft throws and crosshead pins. ? Cooling: Tube-and-shell coolers are optional add-on components, which provide remote cooling capacity. The HT-400 pump can be fitted with radiator-type, air-to-oil or water-to-oil cooling systems as well.

Fluid end view

Spacers are special components designed to separate the fluid end from the power end of the HT-400 pump. The interchangeable spacer insures that fluids being pumped do not contaminate the power end and cause premature failures. Each fluid end package is manufactured from three separate chambers – all identical and completely interchangeable. If one chamber of a fluid end should cause trouble, it can be changed quickly and the pump returned to duty. Fluid End components: ? Chambers: The fluid end is constructed from three separate but identical forged and heat-treated chambers. Fluid ends can be supplied in any of five plunger sizes and each size can be fitted to the standard power end without alteration of either fluid or power end. ? Valves and valve seats: Fluid ends are fitted with replaceable, carburized valves and seats of Halliburton design and manufacture. Most of the valve assembly parts are interchangeable between suction and discharge ports within a given size and some are even interchangeable between sizes. ? Lubrication: A separate lubrication system supplies lubricant to the fluid end package.

HALLIBURTON

HAL17345

Testing
Each HT-400 pump undergoes rigorous testing before it is placed in service. Fluid end chambers are tested individually to pressures far beyond the anticipated operating pressures and then tested again when they are assembled into three-chamber fluid ends. A third test is performed after the fluid end is attached to the power end assembly. Power ends are submitted to equally rigorous testing in a Halliburton test facility. Pumps are run for over an hour at various speeds and at various pumping pressures before they are installed on a unit. After the unit is completed, each pump is further tested during the unit checkout.
Mounted on a skid — close-up

Simulation/Cementing Service
Plunger Dia., Inches Maximum Pressure Maximum Rate @ 275 Crankshaft RPM GPM BPM Maximum HP Input 810 19.3 800 560 13.3 800 454 10.8 800 360 8.6 800 255 6.1 800 6 in. 6,250 5 in. 9,000 4 1/2 in. 4 in. 3 3/8 in. 11,200 14,000 20,000

Plunger Dia., Inches Maximum Pressure Maximum Rate @ 75 Crankshaft RPM GPM BPM Maximum HP Input

6 in. 3,000 221 5.3 275

5 in. 4,500 153 3.6 275

4 1/2 in. 4 in. 3 3/8 in. 5,600 124 2.9 275 7,000 98 2.3 275 10,000 65 1.5 275
Fluid end ring gear view

Mounted on Advantage? skid unit — side view

www.halliburton.com
H04798 04/06 ? 2006 Halliburton All Rights Reserved Printed in U.S.A. Sales of Halliburton products and services will be in accord solely with the terms and conditions contained in the contract between Halliburton and the customer that is applicable to the sale.

HAL17348

HAL17347

Drilling/Industrial Services

HAL17346


相关文章:
⊙哈里伯顿配件
我司销售哈里伯顿HALLIBURTON公司产品,包括HT-400大泵配件,测井配件及压裂车,固井...including HT-400 big pump parts, accessories and fracturing well logging car...
固井常用单词和句子
primary cementing 固井泵 1. cementing pump 2. cementing unit 固井不合格 1. cement failure 2.defective casing/liner cementation 固井操作 cementing job 固井...
800型压裂泵总体设计
[Key words] Fracturing pump Linkage crankshaft ...1.3.2.1 美国哈里伯顿公司 HQ-2000 压裂酸化机组...② HT-3000B 增压泵(液压驱动) ,HT-400 泵(...
往复泵动力端设计
钻井往复泵原理与设计.机械工业出版社. 4.国内外现状和发展趋势与研究的主攻方向 HT-400 固井泵 1.型号 HT-400 泵是固井行业应用最广泛的高压泵,效率高达 95....
自动混浆双机双泵固井水泥车简介
哈里伯顿 CPT-Y4 型自动混浆双机双泵固井水泥车每...变速箱选用美国艾里逊 HT-750 型,注水 泥选用...400型系列固井水泥车技术... 22页 1下载券 混浆...
固井泵动力端开题报告
机械工业出版社. 4.国内外现状和发展趋势与研究的主攻方向 第 3 页共 11 页 开题报告 HT-400 固井泵 1.型号 HT-400 泵是固井行业应用最广泛的高压泵,效率...
压裂泵阀箱 制造标准
本标准结合了国外(斯伦贝谢,哈里伯顿公司的技术规范,具体阐述了液力端相关 的加工...300 SPM2000 HT400 FMC2700 TWS600S GD2500 5ZB2500 5ZB2800 ...
俄罗斯固井质量测井仪器与哈里伯顿INSITE系列测井系统的挂接
俄罗斯固井质量测井仪器与哈里伯顿 INSITE 系列测井系统的挂接 【摘要】 本文介绍了俄罗斯固井质量测井仪器的基本特性及功能,重点是解 决了实际生产中不同测井系统挂...
更多相关标签:
哈里伯顿 | 哈里伯顿公司 | 哈里伯顿中国官网 | 哈里伯顿中国公司官网 | 哈里伯顿招聘 | 哈里伯顿官网 | 哈里伯顿中国 | 哈里伯顿裁员 |