当前位置:首页 >> 机械/仪表 >>

A-Lok双卡套接头


A-LOK Tube Fittings

Catalog 4233 Revised, October 1999

A-LOK Tube Fittings
Introduction
Parker A-LOK Instrumentation Tube Fittings are designed as leak-free c

onnections for process, power and instrumentation applications. These two ferrule fittings are manufactured to the highest quality standards and are available in a broad range of sizes, materials and configurations.


Torque
Parker A-LOK tube fittings do not twist the tubing during installation. A-LOK's ferrule design assures that all make and remake motion is transmitted axially to the tubing. Since no radial movement of the tubing occurs, the tubing is not stressed. The mechanical integrity of the tubing is maintained.

Features
The Parker A-LOK tube fitting has been specifically designed for use on instrumentation, process and control systems, analysers and environmental equipment employed in chemical, petroleum, power generating and pulp and paper plants. The A-LOK tube fitting has also found extensive application in other fields where a high quality tube fitting is required.


No Distortion
In make-up, there is no undue force in an outward direction to distort the fitting body or ferrules to cause interference between the ferrules and nut. This assures that the nut will back-off freely for disassembly and permits a greater number of easy remakes.

Sealing
Positive, reliable connections with Parker A-LOK fittings have been qualified by exhaustive tests and over four decades of experience in the manufacture of quality tube fittings.

Materials
Parker A-LOK fittings are available as standard in Heat Code Traceable, 316 stainless steel. Other standard materials include steel, brass, aluminum, nickel-copper, Hastelloy C, Alloy 600, Titanium, 6Mo, Incoloy 625 and 825. Straight fittings are machined from cold finished bar stock and shaped bodies are machined from close grain forgings. The raw materials used fully conform to the chemical requirements listed in Specification Table 1. For nuclear and other critical applications, stainless steel A-LOK fittings are readily available with documented heat code traceability.


Nomenclature
Parker A-LOK fittings part numbers are constructed from symbols that identify the size and style of the fitting and material used.

Assembly, Remake, Gaugeability
For proper assembly and remake of Parker A-LOK tube fittings, refer to page 74 in the engineering report section. For gauging of Parker A-LOK tube fittings, refer to page 74.

Pipe Fittings/Adapters
Parker A-LOK tube fittings are available in a wide variety of ISO and ANSI pipe thread configurations. For a full line of these fittings, see Catalog 4260.

Pressure Rating & Tubing Selection
For working pressures of A-LOK tube connections, please see the Instrument Tubing Selection Guide, found in the Technical Section of your Parker Instrumentation Products Master Binder, or the Parker Instrument Tube Fitting Installation Manual (Bulletin 4200-B4). In some cases where a male or female pipe thread is the second end of a Parker A-LOK fitting, such threads may be the pressure limiting factor of the tubing system. See Catalog 4260, Instrumentation Pipe Fittings for pressure ratings of Parker Instrumentation Pipe Fittings.

Tubing
Parker A-LOK tube fittings can be used with a wide variety of tubing materials and a broad range of tube wall thicknesses. A-LOK seals equally well on both thin wall and heavy wall tubing. Tubing and fitting materials should be selected to be compatible with the fluid media. Due to thermal expansion characteristics and chemical stability, the tubing should be of the same material as the fitting. (The exception is brass fittings and copper tubing.)

Huntsville, Alabama, USA

Barnstaple, UK

2
Parker Hannifin Corporation

A-LOK Tube Fittings
The Parker A-LOK twin ferrule fitting consists of four precision engineered parts designed to provide secure leak-proof joints capable of satisfying high pressure, vacuum and vibration applications.

Inch
The Parker Suparcase back ferrule provides a strong mechanical and anti-vibration hold on the tube Pressure seal by front ferrule on tube and body

Parker’s high quality, silver plated nut ensures no galling of body threads

Deep tube abutment and close tolerance of nut and body for accurate tube alignment

Metric
The Parker Suparcase back ferrule provides a strong mechanical and anti-vibration hold on the tube

Metric identification shoulder

Pressure seal by front ferrule on tube and body

Parker’s high quality, silver plated nut ensures no galling of body threads

Deep tube abutment and close tolerance of nut and body for accurate tube alignment

Parker Instrumentation Tube Fittings are supplied complete and ready to use. The front ferrule swages onto the tube as it moves down the body seat creating a pressure/vacuum-tight seal on both tube and body by the interface pressure and surface finish of mating components. The Parker Suparcase back ferrule then moves inwards in the cone of the front ferrule, forming into the tube and creating a strong mechanical hold on the tube.

WARNING
FAILURE, IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.

Offer of Sale
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the “Offer of Sale”.

Copyright 1999, Parker Hannifin Corporation. All Rights Reserved.

3
Parker Hannifin Corporation

A-LOK Tube Fittings
Visual Index
Tube to Male Pipe
MSCN MSCK MSCR Male Connnector FBCN Female Bulkhead Connector EE EEM ELZ Union Elbow TUHA Tube End to SAE Straight Thread Adapter

page 22
BSPP

page 42
FAN FAK FAR Tube End Female Adapter

page 8, 9, 10, 11, 12
GCR Gauge Connector MBCN Male Bulkhead Connector

page 29, 30

page 22, 23
ET ETM Union Tee

page 42, 43, 44
P2T3 Push-Lok to Tube Adapter

page 13
FELN Female Elbow MTCN Thermocouple Connector

page 23

page 31

page 44
P2HF Push-Lok to Male Adapter

page 14
JLZ Drop Size Tee FRTN Female Run Tee

MSELN MSELK Male Elbow

page 45

page 32
P2LZ6 Push-Lok to A-LOK

page 14, 15, 16

page 24

page 45
FBTN Female Branch Tee ZP2 Push-Lok to Port Connector

MVELN NPT Male 45° Elbow

page 17

page 25

Tube to Tube Unions
SC SCM Union

ECR ECRM Union Cross

page 45

page 33
LJF Lapped Joint Tube Adaptors

page 26
MRTN NPT Male Run Tee

Port Connectors
TUR TUCM TURM Tube End Reducer

page 46

page 18
CU Conversion Union

page 26
RU RUM Reducing Union

page 34, 35, 36

ZH2X DP Transmitter Calibration Adapters

page 46

MBTN NPT Male Branch Tee

TUBC Tube End Bulkhead Adapter

37° Flare (AN) to A-LOK
X6TU 37° Flare (AN) to A-LOK

page 27
BC BCM Bulkhead Union

page 36
PC PCM Port Connector

page 19

page 47

Tube to Female Pipe
FSCN FSCK Female Connnector

page 37
MAN MAR MAK Tube End Male Adapter XASC 37° Flare Connector to A-LOK

page 28

page 20, 21

page 47

DELTA Dielectric Union Adapter, Dielectric Assembly

page 38, 39, 40, 41

page 29

XABC 37° Flare Bulkhead Connector to A-LOK

page 47

4
Parker Hannifin Corporation

A-LOK Tube Fittings
Visual Index
Tube to “O” Ring Seal
M1SC Male Connector SAE Straight Thread M5VEL 45° Positionable Male Elbow ZHLW2 Buttweld Connector HCS Hose Connector Sleeve

page 53

page 59, 60

page 66

page 49
M2SC Male Connector to “O” Ring Straight Thread

Analytical Fittings
Z2HLZ7 Column End Fitting

Components
TIZ Insert

page 67
NU NUM Tube Nut

M5SEL Male SAE Straight Thread Elbow

page 54

page 62

page 50
M3SC Male Connector to “O” Ring Pipe Thread Z3HLZ7 Column End Fitting

page 67, 68
BZI Inverted Tube Nut

MSEL (R) Male BSPP Straight Thread Elbow

page 62

page 68
BZP Knurled Nut

page 50
M2TU Tube End to “O” Ring Straight Thread

M5RT Male Run Tee SAE Straight Thread

page 51
BSPP

MRT (R) Male BSPP Run Tee Straight Thread

page 51

M5BT Male Branch Tee SAE Straight Thread

page 52
ZELW Socket Weld Elbow MBT (R) Male BSPP Branch Tee Straight Thread
BSPP

page 52
ZH3LA Long Male Connector SAE Straight Thread

page 53

BSPP

page 54
ZHLZ7 Column End Fitting (without Frit)

page 68
FF FFM Front Ferrules

page 63

page 55
M3TU Tube End to “O” Ring Pipe Thread Z2HLZ Column End Fitting

page 69
BF BFM Back Ferrules

page 63

page 69

page 55
FHOA Pipe Thread to SAE Straight Thread Adapter ZHLZ Column End Fitting (without Frit) Ferrule Holder

page 69
BLP BLPM Plug

page 64

page 56
Z7HLZ7 Union Connector

page 70
BLEN BLENM Cap

AH2LZ Bulkhead to Conversion Adapter

page 64
FLZ7 Male Connector

page 56

page 70, 71
MDF Vent Protector

Tube to Welded Systems

page 65
ZHLS Sanitary Flange Fitting

page 71
Sealing Washers

page 65

page 58

page 72
WLZ WLN Bulkhead Locknut

Barbed Fittings
ZELW2 Buttweld Elbow B2HF Barbed Connector to Male Pipe

page 73
BN Bulkhead Locknut

page 58

page 66
B2TU Barbed Connector to Tube Adapter

page 73
L5N Accessory Locknut

ZHLW Socket Weld Connector

page 59

page 66

page 73

5
Parker Hannifin Corporation

A-LOK Tube Fittings
Table 1 – Typical Raw Material Specifications
BASIC FITTING MATERIAL BAR STOCK FORGING COMMON TUBING SPECIFICATION

BRASS

CA-360 QQ-B 626 Alloy 360 ASTM-B16 Alloy 360 CA-345 ASTM-B-453 Alloy 345 BS970 316-S31 DIN 4401 ASME SA479-316 ASME-SA-479 Type 316-SS BS970 316-S31 DIN 4401

CA-377 QQ-B 626 Alloy 377 ASTM-B-124 Alloy 377 BS2872 CZ122

ASTM-B75 ASME-SB75 (TEMPER "O")

STAINLESS STEEL (Type 316)(1)

ASME-SA-182 316 BS970 316-S31 DIN 4401

ASME-SA-213 ASTM-A-213 ASTM-A-249 ASTM-A-269(2) MIL T-8504 MIL T-8506 SAE J524b SAE J525b ASTM-A-179 303, 6061T6 ASTM-B-210

STEEL

ASTM-A-108 QQ-S-637 2017-T4 or 2024-T4 ASTM-B211 QQ-A-225/5 or 6 ASTM-B-164 QQ-N-281 BS3076 NA13 ASTM-B-574 ASTMB575 ASTM B-166 ASME-SB-166 ASTM-B-473 ASTM-B-348 BS3076 NA16 ASTMB425

ASTM-A-576

ALUMINUM

2014T (as fabricated) ASTM-B-211 QQ-A-225/4 ASTM-B-164 QQ-N-281 BS3076 NA13 ASTM-B-574 ASTM-B-564 ASTM-B-462 ASTM-B-472 ASTM-B-381 BS3076 NA16 ASTMB425

NICKEL-COPPER

ASTM-B-165 ASTM-B-622 ASTM-B-626 ASTM-B-163 ASTM-B-468 ASTM-B-338 ASTM-B-625 ASTM-B-444 ASTM-B-423 ASTM-B-829 ASTM-A-269

HASTELLOY C-276 ALLOY 600 CARPENTER 20 TITANIUM INCOLOY 625 INCOLOY 825 6MO

UNS S31254 ASTM A479

UNS S31254 ASTM A 479

(1) If more specific information, including heat code traceability, is required, your Parker Hannifin A-LOK distributor will provide details. (2) Stainless steel A-LOK tube fittings work reliably on both seamless and welded-redrawn, fully annealed type 304, 316 and 316L tubing.

Tube End Dimensional Data
INCHES A-LOK STRAIGHT THREAD D TUBE INS. DEPTH
H HEX

INCHES
C A-LOK STRAIGHT THREAD

MILLIMETERS A-LOK STRAIGHT THREAD D TUBE INS. DEPTH

SIZE NO.

TUBE O.D.

C

H HEX

E DIA.

SIZE NO.

TUBE O.D.

C

H HEX

E DIA.

1 2 3 4 5 6 8 10 12 14 16 20 24 32

1/16 1/8 3/16 1/4 5/16

10-32 5/16-20 3/8-20 7/16-20 1/2-20

.43 .60 .64 .70 .73

5/16 7/16 1/2 9/16 5/8

.052 .093 .125 .187 .250

.34 .50 .54 .60 .64 .67 .90 .96 .96 1.03 1.24 1.61 1.96 2.65

E

D

2 3 4 6 8 10 12 14 15 16 18 20 22 25

2mm 3mm 4mm 6mm 8mm

5/16-20 5/16-20 3/8-20 7/16-20 1/2-20

15,3 15,3 16,1 17,7 18,6 19,5 22,0 22,0 22,0 22,0 22,0 22,0 22,0 26,5

12,0 12,0 12,0 14,0 15,0 18,0 22,0 24,0 24,0 24,0 27,0 30,0 30,0 35,0

1,7 2,4 2,4 4,8 6,4 7,9 9,5 11,1 11,9 12,7 15,1 15,9 18,3 21,8

12,9 12,9 13,7 15,3 16,2 17,2 22,8 24,4 24,4 24,4 24,4 26,0 26,0 31,3

3/8 9/16-20 .76 11/16 .281 1/2 3/4-20 .87 7/8 .406 5/8 7/8-20 .87 1 .500 3/4 1-20 .87 1-1/8 .625 7/8 1-1/8-20 .87 1-1/4 .750 1 1-5/16-20 1.05 1-1/2 .875 1-1/4 1-5/8-20 1.52 1-7/8 1.09 1-1/2 1-15/16-20 1.77 2-1/4 1.34 2 2-5/8-20 2.47 2-3/4 1.81

MILLIMETERS
H HEX C A-LOK STRAIGHT THREAD

E

10mm 5/8-20 12mm 3/4-20 14mm 7/8-20 15mm 7/8-20 16mm 7/8-20 18mm 1-20 20mm 1-1/8-20 22mm 1-1/8-20 25mm 1-5/16-20

NOTE: Dimensions C and D are shown in the fingertight position. Average Value Dimensions for reference only, subject to change.

D

NOTE: Dimensions C and D are shown in the fingertight position. Average Value Dimensions for reference only, subject to change.

6
Parker Hannifin Corporation

A-LOK Tube Fittings
Nomenclature
Parker A-LOK tube fittings part numbers are constructed from symbols that identify the size and style of the fitting and material used. Example: The part number shown below is for a Parker A-LOK stainless steel male connector for 1/2" O.D. tube (–8) and 1/4" male pipe thread (–4).

How To Order Inch Parts
8 MSC 4 N 316 1st End 1/2" Tube O.D. Fitting Type Male Connector 2nd End 1/4" Pipe Thread Thread Type NPT Material Stainless Steel

Parker A-LOK Tube Fittings are ordered by part number as listed in this catalog. 4 Size: Tube and pipe thread sizes are designed by the number of sixteenths of an inch (1/2" tube = 8/16" = 8). (1/4" pipe thread = 4/16" = 4). 1 Straights & Elbows: Call out largest A-LOK tube end size first followed by the smaller A-LOK tube end or pipe thread size. Tees & Crosses: For drop size tees – first size the run (1 to 2) and then branch (3). Example – the size des2 ignator for a male run tee for 3/8" O.D. tube and 1/4" male pipe thread would be 6-4-6. For crosses – first size the run (1 to 2) and then the branch (3 to 4). For tees with all ends the same, use the tube and size before 3 and after the style designator; i.e. 4ET4. Type: A letter or combination of letters and numbers are used to designate the type of fitting. (i.e. MBT = male branch tee, FA = female adapter, etc.) See the visual index for fitting types. Material: Basic material type (B = brass, 316 = stainless steel, type 316; S = steel; A = aluminum; M = Monel; HC = Hastelloy C-276; IN = Alloy 600; SS20 = Carpenter 20; 6MO = 6Mo; 625 = 625; 825 = 825; T = Titanium). Parker A-LOK Tube fittings, for special applications, can be furnished in almost any material suitable for machining. Special Fittings: If there is any question as to the fitting desired, particularly for special fitting configurations, it is suggested that a customer print be submitted with the fitting request for quote. Availability: Items priced in current price list 4233 are carried in stock. Price and delivery for non-stocked items quoted on request through the Quick Response Department.

How To Order Metric Parts
M12 FSC 1/4 N 316 Tube O.D. 12mm Style Female Connector Thread Size 1/4" Thread Type* NPT Material Stainless Steel

Parker A-LOK tube fittings are ordered by part number as listed in this catalog. Size: Metric tube is designated in millimeters and prefixed “M” (i.e. 12mm tube = M12.) The pipe thread size is written as a fraction (i.e. 1/4 NPT = 1/4N). Straights & Elbows: Call out largest A-LOK tube end size first followed by the smaller A-LOK tube end or pipe thread size. Tees & Crosses: For drop size tees – first size the run (1 to 2) and then branch (3). Example – the size designator for a male run tee for 6mm tube and 1/4" male pipe thread would be 6-4-6. For crosses – first size the run (1 to 2) and then the branch (3 to 4). For tees with all ends the same size, use the tube end size after the style designator; i.e, ETM4
1

4

2 3

Type: A letter or combination of letters and numbers are used to designate the type of fitting. See the visual index for fitting types. Material: Basic material type (B = brass, 316 = stainless steel, type 316; S = steel; A = aluminum; M = Monel; HC = Hastelloy C-276; IN = Alloy 600; SS20 = Carpenter 20; 6MO = 6Mo; 625 = 625; 825 = 825; T = Titanium). Parker A-LOK Tube fittings, for special applications, can be furnished in almost any material suitable for machining. Thread types: N = NPT K = BSP Taper R = BSPP BR = BSPP M = Metric RED = BSPP Please see visual index. Availability: Items priced in current price list 4233 are carried in stock. Price and delivery for non-stocked items quoted on request through the Parker ICD Quick Response Department.
NOTE: Hastelloy C-276 is a registered trademark of Cabot Corporation. Carpenter 20 is a registered trademark of Carpenter Technology Corporation.

Color Coding
ANSI B1.20.1 BS21, ISO7/1 BS2779, ISO 228/1+2, DIN BS2779, ISO 228/1+2, DIN BS2779, ISO 228/1+2, DIN BS2779, ISO 228/1+2, DIN with elastic sealing

For easy reference, table heads are color indicated as follows:
3852 FORM A 3852 FORM B 3852 3852

fractional metric

7
Parker Hannifin Corporation

Tube to Male Pipe MSCN
NPT Male Connector
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD A C D R W HEX

1MSC1N 1MSC2N 1MSC4N 2MSC1N 2MSC2N 2MSC4N 2MSC6N 2MSC8N 3MSC1N 3MSC2N 3MSC4N 4MSC1N 4MSC2N 4MSC4N 4MSC6N

100-1-1 100-1-2 100-1-4 200-1-1 200-1-2 200-1-4 200-1-6 200-1-8 300-1-1 300-1-2 300-1-4 400-1-1 400-1-2 400-1-4 400-1-6 400-1-8 400-1-12 500-1-2 500-1-4 500-1-6 500-1-8 600-1-2 600-1-4 600-1-6 600-1-8 600-1-12 810-1-2 810-1-4 810-1-6 810-1-8 810-1-12 810-1-16 1010-1-6 1010-1-8 1010-1-12 1210-1-8 1210-1-12 1210-1-16 1410-1-12 1410-1-16 1610-1-8 1610-1-12 1610-1-16 2010-1-20 2410-1-24 3210-1-32

1/16 1/16 1/16 1/8 1/8 1/8 1/8 1/8 3/16 3/16 3/16 1/4 1/4 1/4 1/4 1/4 1/4 5/16 5/16 5/16 5/16 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 3/4 3/4 3/4 7/8 7/8 1 1 1 1-1/4 1-1/2 2

1/16 1/8 1/4 1/16 1/8 1/4 3/8 1/2 1/16 1/8 1/4 1/16 1/8 1/4 3/8 1/2 3/4 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 3/4 1/8 1/4 3/8 1/2 3/4 1 3/8 1/2 3/4 1/2 3/4 1 3/4 1 1/2 3/4 1 1-1/4 1-1/2 2

.93 1.03 1.23 1.17 1.20 1.40 1.42 1.67 1.23 1.23 1.43 1.29 1.29 1.49 1.51 1.76 1.82 1.34 1.52 1.55 1.79 1.38 1.57 1.57 1.82 1.88 1.53 1.71 1.71 1.93 1.99 2.28 1.74 1.93 1.99 1.99 1.99 2.28 1.99 2.28 2.27 2.27 2.46 3.03 3.50 4.47

.43 .43 .43 .60 .60 .60 .60 .60 .64 .64 .64 .70 .70 .70 .70 .70 .70 .73 .73 .73 .73 .76 .76 .76 .76 .76 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 1.05 1.05 1.05 1.52 1.77 2.47

.78 .88 1.08 .91 .94 1.14 1.16 1.41 .97 .97 1.17 1.00 1.00 1.20 1.22 1.47 1.53 1.05 1.23 1.25 1.5 1.09 1.28 1.28 1.53 1.59 1.13 1.31 1.31 1.53 1.59 1.88 1.34 1.53 1.59 1.59 1.59 1.88 1.59 1.88 1.78 1.78 1.97 2.17 2.44 3.00

.38 .38 .56 .38 .38 .56 .56 .75 .38 .38 .56 .38 .38 .56 .56 .75 .75 .38 .56 .56 .75 .38 .56 .56 .75 .75 .38 .56 .56 .75 .75 .94 .56 .75 .75 .75 .75 .94 .75 .94 .75 .75 .94 .97 1.00 1.04

5/16 7/16 9/16 3/8 7/16 9/16 11/16 7/8 7/16 7/16 9/16 1/2 1/2 9/16 11/16 7/8 1-1/16 9/16 9/16 11/16 7/8 5/8 5/8 11/16 7/8 1-1/16 13/16 13/16 13/16 7/8 1-1/16 1-3/8 15/16 15/16 1-1/16 1-1/16 1-1/16 1-3/8 1-3/16 1-3/8 1-3/8 1-3/8 1-3/8 1-3/4 2-1/8 2-3/4

A C R

W HEX D

4MSC8N 4MSC12N 5MSC2N 5MSC4N 5MSC6N 5MSC8N 6MSC2N 6MSC4N 6MSC6N 6MSC8N 6MSC12N 8MSC2N 8MSC4N 8MSC6N 8MSC8N 8MSC12N 8MSC16N 10MSC6N 10MSC8N 10MSC12N 12MSC8N 12MSC12N 12MSC16N 14MSC12N 14MSC16N 16MSC8N 16MSC12N 16MSC16N 20MSC20N 24MSC24N 32MSC32N

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

Color Coding
For easy reference, table heads are color indicated as follows:

fractional metric

8
Parker Hannifin Corporation

Tube to Male Pipe MSCN
NPT Male Connector
For metric tube
PARKER PART NO. INTERCHANGES WITH MILLIMETERS TUBE O.D. NPT THREAD A C D R W HEX

M2MSC1/8N M3MSC1/8N M3MSC1/4N M4MSC1/8N M4MSC1/4N M6MSC1/8N M6MSC1/4N M6MSC3/8N M6MSC1/2N M8MSC1/8N M8MSC1/4N M8MSC3/8N M8MSC1/2N M10MSC1/8N M10MSC1/4N

2MO-1-2 3MO-1-2 3MO-1-4 4MO-1-2 4MO-1-4 6MO-1-2 6MO-1-4 6MO-1-6 6MO-1-8 8MO-1-2 8MO-1-4 8MO-1-6 8MO-1-8 10MO-1-2 10MO-1-4 10MO-1-6 10MO-1-8 10MO-1-12 10MO-1-16 12MO-1-4 12MO-1-6 12MO-1-8 12MO-1-12 14MO-1-4 14MO-1-6 14MO-1-8 15MO-1-8 16MO-1-6 16MO-1-8 16MO-1-12 18MO-1-8 18MO-1-12 20MO-1-8 20MO-1-12 20MO-1-16 22MO-1-12 25MO-1-8 25MO-1-12 25MO-1-16

2 3 3 4 4 6 6 6 6 8 8 8 8 10 10 10 10 10 10 12 12 12 12 14 14 14 15 16 16 16 18 18 20 20 20 22 25 25 25

1/8 1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 3/4 1 1/4 3/8 1/2 3/4 1/4 3/8 1/2 1/2 3/8 1/2 3/4 1/2 3/4 1/2 3/4 1 3/4 1/2 3/4 1

29,7 29,7 35,3 31,2 36,3 32,9 38,1 38,5 44,8 34,2 38,8 39,3 45,6 36,1 40,9 40,9 47,5 46,4 55,0 43,4 43,4 49,0 50,5 44,2 44,2 49,0 49,0 44,1 49,0 50,5 50,6 50,6 50,6 52,3 57,7 52,3 57,5 57,5 62,3

15,3 15,3 15,3 16,1 16,1 17,7 17,7 17,7 17,7 18,6 18,6 18,6 18,6 19,5 19,5 19,5 19,5 19,5 19,5 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 26,5 26,5 26,5

23,1 23,1 28,7 24,6 29,7 25,4 30,6 31,0 37,3 26,7 31,3 31,8 38,1 28,6 33,3 33,3 38,9 38,9 47,5 33,3 33,3 38,9 40,4 34,1 34,1 38,9 38,9 34,01 38,9 40,5 40,5 40,5 42,2 42,2 47,6 42,2 45,3 45,2 50,0

9,5 9,5 14,3 9,5 14,3 9,5 14,3 14,3 19,1 9,5 14,3 14,3 19,1 9,5 14,3 14,3 19,1 19,1 23,8 14,3 14,3 19,1 19,1 14,3 14,3 19,1 19,1 14,3 19,1 19,1 19,1 19,1 19,1 19,1 23,8 19,1 19,1 19,1 23,8

12,0 12,0 14,0 12,0 14,0 14,0 14,0 18,0 22,0 15,0 15,0 18,0 22,0 18,0 18,0 18,0 22,0 27,0 35,0 22,0 22,0 22,0 27,0 24,0 24,0 24,0 24,0 24,0 24,0 27,0 27,0 27,0 30,0 30,0 35,0 35,0 35,0 35,0 35,0

A C R

W HEX D

M10MSC3/8N M10MSC1/2N M10MSC3/4N M10MSC1N M12MSC1/4N M12MSC3/8N M12MSC1/2N M12MSC3/4N M14MSC1/4N M14MSC3/8N M14MSC1/2N M15MSC1/2N M16MSC3/8N M16MSC1/2N M16MSC3/4N M18MSC1/2N M18MSC3/4N M20MSC1/2N M20MSC3/4N M20MSC1N M22MSC3/4N M25MSC1/2N M25MSC3/4N M25MSC1N

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

9
Parker Hannifin Corporation

Tube to Male Pipe MSCK
BSP Taper Male Connector
For fractional tube
BSP

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. BSP TR THREAD A C D R W HEX BORE

2MSC2K 2MSC4K 4MSC2K 4MSC4K 4MSC6K 4MSC8K 5MSC2K 5MSC4K 6MSC2K 6MSC4K 6MSC6K 6MSC8K 8MSC4K 8MSC6K 8MSC8K

200-1-2RT 200-1-4RT 400-1-2RT 400-1-4RT 400-1-6RT 400-1-8RT 500-1-2RT 500-1-4RT 600-1-2RT 600-1-4RT 600-1-6RT 600-1-8RT 810-1-4RT 810-1-6RT 810-1-8RT

1/8 1/8 1/4 1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2

1/8 1/4 1/8 1/4 3/8 1/2 1/8 1/4 1/8 1/4 3/8 1/2 1/4 3/8 1/2

1.20 1.40 1.30 1.50 1.52 1.77 1.34 1.52 1.39 1.57 1.57 1.82 1.69 1.69 1.91

.60 .60 .70 .70 .70 .70 .73 .73 .76 .76 .76 .76 .86 .86 .66

.938 1.14 1.00 1.20 1.22 1.47 1.05 1.23 1.09 1.28 1.28 1.53 1.31 1.31 1.53

.38 .56 .38 .56 .56 .75 .38 .56 .38 .56 .56 .75 .56 .56 .75

7/16 9/16 1/2 9/16 11/16 7/8 9/16 9/16 5/8 5/8 11/16 7/8 13/16 13/16 7/8

.19 .19 .19 .19 .19 .19 .19 .19 .19 .28 .28 .28 .28 .38 .41

A C R

BSP

NOTE: A and C dimensions are typical finger-tight. W HEX D

Dimensions for reference only, subject to change.

MSCK
BSP Taper Male Connector
For metric tube
BSP

PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. BSP TR THREAD A C D R W HEX

M2MSC1/8K M3MSC1/8K M3MSC1/4K M4MSC1/8K M4MSC1/4K M6MSC1/8K M6MSC1/4K M6MSC3/8K M6MSC1/2K M8MSC1/8K

2MO-1-2RT 3MO-1-2RT 3MO-1-4RT 4MO-1-2RT 4MO-1-4RT 6MO-1-2RT 6MO-1-4RT 6MO-1-6RT 6MO-1-8RT 8MO-1-2RT 8MO-1-4RT 8MO-1-6RT 8MO-1-8RT 10MO-1-2RT 10MO-1-4RT 10MO-1-6RT 10MO-1-8RT 12MO-1-4RT 12MO-1-6RT 12MO-1-8RT 12MO-1-12RT 15MO-1-8RT 16MO-1-6RT 16MO-1-8RT 16MO-1-12RT 18MO-1-8RT 18MO-1-12RT 20MO-1-8RT 20MO-1-12RT 22MO-1-12RT 25MO-1-12RT 25MO-1-16RT

2 3 3 4 4 6 6 6 6 8 8 8 8 10 10 10 10 12 12 12 12 15 16 16 16 18 18 20 20 22 25 25

1/8 1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/4 3/8 1/2 3/4 1/2 3/8 1/2 3/4 1/2 3/4 1/2 3/4 3/4 3/4 1

29,7 29,7 35,3 31,2 36,3 32,9 40,0 38,5 45,6 33,9 38,7 39,3 45,6 36,2 40,9 40,9 46,5 43,4 43,4 49,0 49,5 49,0 44,2 49,0 49,5 50,6 50,6 52,3 52,3 52,3 57,5 62,3

15,3 15,3 15,3 16,1 16,1 17,7 17,7 17,7 17,7 18,6 18,6 18,6 18,6 19,5 19,5 19,5 19,5 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 26,5 26,5

23,1 23,1 28,7 24,6 29,7 25,4 30,5 31,0 38,1 26,4 31,2 31,8 38,1 28,6 33,3 33,3 38,9 33,3 33,3 38,9 40,4 38,9 34,1 38,9 40,5 40,4 40,4 42,2 42,2 42,2 45,2 50,0

9,5 9,7 14,2 9,7 14,2 9,7 14,2 14,2 19,1 9,5 14,2 14,2 19,1 9,5 14,2 14,2 19,1 14,2 14,2 19,1 19,1 19,1 14,2 19,1 19,1 19,1 19,1 19,1 19,1 19,1 19,1 23,9

12,0 12,0 14,0 12,0 14,0 14,0 14,0 18,0 22,0 15,0 15,0 18,0 22,0 18,0 18,0 18,0 22,0 22,0 22,0 22,0 27,0 24,0 24,0 24,0 27,0 27,0 27,0 30,0 30,0 30,0 35,0 35,0

A C R

M8MSC1/4K M8MSC3/8K M8MSC1/2K M10MSC1/8K M10MSC1/4K M10MSC3/8K M10MSC1/2K M12MSC1/4K M12MSC3/8K M12MSC1/2K M12MSC3/4K M15MSC1/2K M16MSC3/8K M16MSC1/2K M16MSC3/4K M18MSC1/2K M18MSC3/4K M20MSC1/2K M20MSC3/4K M22MSC3/4K M25MSC3/4K M25MSC1K

BSP

W HEX D

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

10
Parker Hannifin Corporation

Tube to Male Pipe MSCR
BSPP Male Connector
For fractional tube
BSPP

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. BSPP THREAD A C D R X W HEX BORE

2MSC2R 2MSC4R 2MSC6R 4MSC2R 4MSC4R 4MSC6R 4MSC8R 6MSC2R 6MSC4R 6MSC6R 6MSC8R 8MSC4R 8MSC6R 8MSC8R 12MSC8R 12MSC12R 16MSC8R 16MSC16R

200-1-2RS 200-1-4RS 200-1-6RS 400-1-2RS 400-1-4RS 400-1-6RS 400-1-8RS 600-1-2RS 600-1-4RS 600-1-6RS 600-1-8RS 810-1-4RS 810-1-6RS 810-1-8RS 1210-1-8RS 1210-1-12RS 1610-1-8RS 1610-1-16RS

1/8 1/8 1/8 1/4 1/4 1/4 1/4 3/8 3/8 3/8 3/8 1/2 1/2 1/2 3/4 3/4 1 1

1/8 1/4 3/8 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/4 3/8 1/2 1/2 3/4 1/2 1

1.18 1.27 1.46 1.28 1.49 1.55 1.77 1.35 1.54 1.57 1.82 1.66 1.69 1.91 1.93 2.07 2.21 2.35

.60 .60 .60 .70 .70 .70 .70 .76 .76 .76 .76 .86 .86 .86 .86 .86 1.04 1.04

.922 1.13 1.172 .98 1.19 1.25 1.47 1.06 1.25 1.28 1.53 1.28 1.31 1.53 1.531 1.69 1.719 1.88

.28 .44 .44 .28 .44 .44 .56 .28 .44 .44 .56 .44 .44 .56 .56 .63 .56 .72

.54 .70 .86 .54 .70 .86 1.01 .54 .70 .86 1.01 .70 .86 1.01 1.01 1.25 1.01 1.52

9/16 3/4 7/8 9/16 3/4 7/8 1-1/16 5/8 3/4 7/8 1-1/16 13/16 7/8 1-1/16 1-1/16 1-3/8 1-3/8 1-5/8

.16 .09 .28 .16 .19 .19 .19 .16 .25 .28 .28 .25 .31 .41 .41 .63 .41 .88

A C R

W HEX D

BSPP

X

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. Sealing washer must be used with BSPP end shown ISO228/1 (Form A). For Form B undercut change part number and add B before R. e.g. M6MSC1/4BR.

MSCR
BSPP Male Connector
For metric tube
BSPP

PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. BSPP THREAD A C D R X W HEX

M2MSC1/8R M3MSC1/8R M3MSC1/4R M6MSC1/8R M6MSC1/4R M6MSC3/8R M6MSC1/2R M8MSC1/8R M8MSC1/4R M8MSC3/8R M8MSC1/2R M10MSC1/4R M10MSC3/8R M10MSC1/2R M12MSC1/4R

2MO-1-2RS 3MO-1-2RS 3MO-1-4RS 6MO-1-2RS 6MO-1-4RS 6MO-1-6RS 6MO-1-8RS 8MO-1-2RS 8MO-1-4RS 8MO-1-6RS 8MO-1-8RS 10MO-1-4RS 10MO-1-6RS 10MO-1-8RS 12MO-1-4RS

2 3 3 6 6 6 6 8 8 8 8 10 10 10 12 12 12 12 16 16 18 18 20 20 22 25 25

1/8 1/8 1/4 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/4 3/8 1/2 1/4 3/8 1/2 3/4 3/8 1/2 1/2 3/4 1/2 3/4 3/4 3/4 1

28,4 30,0 35,3 32,5 37,7 39,0 45,6 33,1 38,5 39,8 45,6 39,4 40,6 46,5 42,6 43,1 49,0 52,8 43,5 49,0 49,0 53,1 50,5 52,8 52,8 59,8 60,1

15,3 15,3 15,3 17,7 17,7 17,7 17,7 18,6 18,6 18,6 18,6 19,5 19,5 19,5 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 26,5 26,5

21,8 23,4 28,7 25,0 30,2 31,5 38,1 25,6 31,0 32,3 38,1 31,8 33,0 38,9 32,5 33,0 38,9 42,7 33,4 38,9 38,9 43,0 40,4 42,7 42,7 47,6 47,8

7,1 7,1 11,2 7,1 11,2 11,2 14,2 7,1 11,2 11,2 14,2 11,2 11,2 14,2 11,2 11,2 14,2 16,0 11,2 14,2 14,2 16,0 14,2 16,0 16,0 16,0 18,3

14,0 13,7 17,8 13,7 17,8 21,8 25,7 15,0 17,8 21,8 25,7 17,8 21,8 25,7 17,8 21,8 25,7 31,8 22,0 26,0 26,0 35,0 30,0 32,0 32,0 35,0 39,0

13,7 14,0 19,0 14,0 19,0 22,0 27,0 13,7 19,0 22,0 27,0 19,0 22,0 27,0 22,0 22,0 27,0 35,0 21,8 27,0 27,0 32,0 25,7 35,0 35,0 31,8 41,0

A C R

W HEX D

BSPP

X

M12MSC3/8R 12MO-1-6RS M12MSC1/2R 12MO-1-8RS M12MSC3/4R 12MO-1-12RS M16MSC3/8R 16MO-1-6RS M16MSC1/2R 16MO-1-8RS M18MSC1/2R M18MSC3/4R M20MSC1/2R M20MSC3/4R M22MSC3/4R 18MO-1-8RS 18MO-1-12RS 20MO-1-8RS 20MO-1-12RS 22MO-1-12RS

M25MSC3/4R 25MO-1-12RS M25MSC1R 25MO-1-16RS

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. Sealing washer must be used with BSPP end shown ISO228/1 (Form A). For Form B undercut change part number and add B before R. e.g. M6MSC1/4BR.

11
Parker Hannifin Corporation

Tube to Male Pipe MSCR
BSPP Male Connector with ED seal
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. BSPP THREAD A C D R X W HEX BORE

4MSCR4-ED 4MSCR8-ED 6MSC6R-ED 8MSC4R-ED 8MSC6R-ED 8MSC8R-ED 12MSC12R-ED

– – – – – – –

1/4 1/4 3/8 1/2 1/2 1/2 3/4

1/4 1/2 3/8 1/4 3/8 1/2 3/4

1.48 1.76 1.60 1.69 1.69 1.85 1.98

.70 .70 .76 .86 .86 .86 .86

1.19 1.38 1.31 1.31 1.31 1.47 1.59

.47 .55 .47 .47 .47 .55 .63

.74 1.04 .86 .74 .86 1.04 1.25

3/4 1-1/16 7/8 13/16 7/8 1-1/16 1-5/16

.19 .19 .28 .25 .31 .41 .63

A C R

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. ED fittings are supplied with sealing washers in Buna-N as standard, suitable for temperatures of between –35°C and +100°C (–31°F to +212°F). Viton seals are available upon request which are suitable for temperatures of between –25°C and +120°C (–13°F to +248°F).

X

W HEX D

MSCR
BSPP Male Connector with ED seal
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. BSPP THREAD A C D R X W HEX

M6MSC1/8R-ED M6MSC1/4R-ED M6MSC3/8R-ED M6MSC1/2R-ED M10MSC1/4R-ED M10MSC3/8R-ED M10MSC1/2R-ED M12MSC1/4R-ED M12MSC3/8R-ED M12MSC1/2R-ED

– – – – – – – – – –

6 6 6 6 10 10 10 12 12 12

1/8 1/4 3/8 1/2 1/4 3/8 1/2 1/4 3/8 1/2

32,5 38,2 39,5 44,5 40,0 41,1 46,0 43,1 43,6 48,5

17,7 17,7 17,7 17,7 19,5 19,5 19,5 22,0 22,0 22,0

25,0 30,7 32,0 37,0 32,3 38,1 38,4 33,0 33,5 38,4

7,9 11,9 11,9 14,0 11,9 11,9 14,0 11,9 11,9 14,0

13,7 18,8 21,8 26,4 18,8 21,8 26,4 18,8 21,8 26,4

14,0 19,0 22,0 27,0 19,0 22,0 27,0 22,0 22,0 27,0

A C R

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. ED fittings are supplied with sealing washers in Buna-N as standard, suitable for temperatures of between –35°C and +100°C (–31°F to +212°F). Viton seals are available upon request which are suitable for temperatures of between –25°C and +120°C (–13°F to +248°F). X

W HEX D

12
Parker Hannifin Corporation

Tube to Male Pipe MBCN
NPT Male Bulkhead Connector
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD A C D L R W HEX

1MBC1N 1MBC2N 2MBC2N 3MBC2N 4MBC2N 4MBC4N 4MBC6N 4MBC8N 5MBC2N 5MBC4N

100-11-1 100-11-2 200-11-2 300-11-2 400-11-2 400-11-4 400-11-6 400-11-8 500-11-2 500-11-4 600-11-2 600-11-4 600-11-6 600-11-8 810-11-4 810-11-6 810-11-8 810-11-12 1010-11-6 1010-11-8 1210-11-8 1210-11-12 1410-11-12 1610-11-12 1610-11-16

1/16 1/16 1/8 3/16 1/4 1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 5/8 5/8 3/4 3/4 7/8 1 1

1/16 1/8 1/8 1/8 1/8 1/4 3/8 1/2 1/8 1/4 1/8 1/4 3/8 1/2 1/4 3/8 1/2 3/4 3/8 1/2 1/2 3/4 3/4 3/4 1

1.19 1.27 1.83 1.89 1.95 2.132 2.162 2.374 2.08 2.27 2.08 2.265 2.265 2.48 2.494 2.494 2.712 2.722 2.628 2.816 3.00 3.00 3.31 3.54 3.72

.68 .68 1.23 1.26 1.31 1.31 1.31 1.31 1.42 1.42 1.44 1.44 1.44 1.44 1.65 1.65 1.65 1.65 1.68 1.68 1.87 1.87 2.09 2.27 2.27

1.038 1.116 1.571 1.634 1.655 1.842 1.872 2.084 1.779 1.966 1.788 1.975 1.975 2.219 2.094 2.094 2.312 2.322 2.228 2.416 2.601 2.601 2.913 3.006 3.194

.53 .53 .97 1.00 1.02 1.02 1.02 1.02 1.12 1.12 1.15 1.15 1.15 1.15 1.25 1.25 1.25 1.25 1.28 1.28 1.47 1.47 1.69 1.78 1.78

.38 .38 .38 .38 .38 .56 .56 .75 .38 .56 .38 .56 .56 .75 .56 .56 .75 .75 .56 .75 .75 .75 .75 .75 .94

5/16 7/16 1/2 9/16 5/8 5/8 11/16 7/8 11/16 11/16 3/4 3/4 3/4 7/8 15/16 15/16 15/16 1-1/8 1-1/16 1-1/16 1-3/16 1-3/16 1-3/8 1-5/8 1-5/8

A C L R

6MBC2N 6MBC4N 6MBC6N 6MBC8N 8MBC4N 8MBC6N 8MBC8N 8MBC12N 10MBC6N 10MBC8N 12MBC8N 12MBC12N 14MBC12N 16MBC12N 16MBC16N

W HEX D

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. For bulkhead hole drill size and maximum bulkhead thickness, see Page 28, Part BC.

MBCN
NPT Male Bulkhead Connector
For metric tube
PARKER PART NO. INTERCHANGES WITH TUBE NPT O.D. THREAD A C

MILLIMETERS B’HEAD HOLE MAX. DRILL B’HEAD SIZE THICK.

D

L

R

W HEX

M6MBC1/8N M6MBC1/4N M8MBC1/8N M8MBC1/4N M10MBC1/4N M10MBC3/8N M10MBC1/2N M12MBC1/4N M12MBC3/8N M12MBC1/2N
R

6MO-11-2 6MO-11-4 8MO-11-2 8MO-11-4 10MO-11-4 10MO-11-6 10MO-11-8 12MO-11-4 12MO-11-6 12MO-11-8

6 6 8 8 10 10 10 12 12 12

1/8 1/4 1/8 1/4 1/4 3/8 1/2 1/4 3/8 1/2

49,6 53,5 52,3 57,5 58,4 58,4 63,1 63,3 64,5 67,5

33,7 33,7 36,0 36,0 37,0 37,0 37,0 10,1 10,1 10,1

42,1 46,0 44,8 50,0 50,8 50,8 55,5 53,2 54,4 57,4

26,2 26,2 28,5 28,5 29,4 29,4 29,4 31,8 31,8 31,8

9,5 14,3 9,5 14,3 14,3 14,3 19,0 14,3 14,3 19,0

16,0 16,0 18,0 18,0 22,0 22,0 22,0 24,0 24,0 24,0

11,5 11,5 13,1 13,1 16,3 16,3 16,3 19,5 19,5 19,5

10,2 10,2 11,2 11,2 11,2 11,2 11,2 12,7 12,7 12,7

A C L

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

W HEX D

13
Parker Hannifin Corporation

Tube to Male Pipe MTCN
Thermocouple Connector
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD A C D R W HEX

1MTC1N 1MTC2N 1MTC4N 2MTC1N 2MTC2N 2MTC4N 3MTC2N 3MTC4N 4MTC2N 4MTC4N 4MTC6N

100-1-1BT 100-1-2BT 100-1-4BT 200-1-1BT 200-1-2BT 200-1-4BT 300-1-2BT 300-1-4BT 400-1-2BT 400-1-4BT 400-1-6BT 400-1-8BT 500-1-4BT 600-1-4BT 600-1-6BT 600-1-8BT 600-1-12BT 810-1-8BT 810-1-12BT 1010-1-12BT 1210-1-12BT 1610-1-16BT

1/16 1/16 1/16 1/8 1/8 1/8 3/16 3/16 1/4 1/4 1/4 1/4 5/16 3/8 3/8 3/8 3/8 1/2 1/2 5/8 3/4 1

1/16 1/8 1/4 1/16 1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/4 1/4 3/8 1/2 3/4 1/2 3/4 3/4 3/4 1

.93 1.03 1.23 1.17 1.20 1.40 1.23 1.43 1.29 1.49 1.60 1.87 1.52 1.57 1.57 1.82 1.88 1.93 1.99 1.99 1.99 2.46

.43 .43 .43 .60 .60 .60 .64 .64 .70 .70 .70 .70 .73 .76 .76 .76 .76 .87 .87 .87 .87 1.05

.78 .88 1.08 .91 .94 1.14 .97 1.17 1.00 1.20 1.22 1.47 1.22 1.28 1.28 1.53 1.59 1.53 1.59 1.59 1.59 1.97

.38 .38 .56 .38 .38 .56 .38 .56 .38 .56 .56 .75 .56 .56 .56 .75 .75 .76 .75 .75 .75 .94

5/16 7/16 9/16 3/8 7/16 9/16 7/16 9/16 1/2 9/16 11/16 7/8 9/16 5/8 11/16 7/8 1-1/16 7/8 1-1/16 1-1/16 1-1/16 1-3/8

A C R

4MTC8N 5MTC4N 6MTC4N 6MTC6N 6MTC8N 6MTC12N 8MTC8N 8MTC12N 10MTC12N 12MTC12N 16MTC16N

W HEX D

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

MSELN
NPT Male Elbow
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. NPT PIPE THREAD C H L R W HEX

1MSEL1N 1MSEL2N 2MSEL1N 2MSEL2N 2MSEL4N 3MSEL2N 3MSEL4N 4MSEL1N 4MSEL2N 4MSEL4N 4MSEL6N 4MSEL8N 5MSEL2N

100-2-1 100-2-2 200-2-1 200-2-2 200-2-4 300-2-2 300-2-4 400-2-1 400-2-2 400-2-4 400-2-6 400-2-8 500-2-2 500-2-4 600-2-2 600-2-4 600-2-6 600-2-8 600-2-12 810-2-4 810-2-6 810-2-8 810-2-12 1010-2-6 1010-2-8 1010-2-12 1210-2-8 1210-2-12 1410-2-12 1610-2-12 1610-2-16 2010-2-20 2410-2-24

1/16 1/16 1/8 1/8 1/8 3/16 3/16 1/4 1/4 1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 5/8 5/8 5/8 3/4 3/4 7/8 1 1 1-1/4 1-1/2

1/16 1/8 1/16 1/8 1/4 1/8 1/4 1/16 1/8 1/4 3/8 1/2 1/8 1/4 1/8 1/4 3/8 1/2 3/4 1/4 3/8 1/2 3/4 3/8 1/2 3/4 1/2 3/4 3/4 3/4 1 1-1/4 1-1/2

.75 .75 .93 .93 .98 1.00 1.01 1.06 1.08 1.07 1.17 1.26 1.17 1.17 1.20 1.20 1.26 1.32 1.45 1.42 1.42 1.43 1.53 1.43 1.43 1.56 1.56 1.56 1.76 1.94 1.94 2.61 3.06

.71 .71 .71 .70 1.00 .74 .94 .74 .76 1.00 1.13 1.31 .82 1.01 .82 1.01 1.13 1.31 1.50 1.12 1.12 1.31 1.50 1.25 1.31 1.50 1.50 1.50 1.66 1.65 1.84 1.88 2.38

.60 .60 .67 .67 .72 .74 .75 .77 .79 .78 .88 .97 .88 .88 .91 .91 .97 1.03 1.16 1.02 1.02 1.03 1.13 1.03 1.03 1.16 1.16 1.16 1.36 1.45 1.45 1.75 2.00

.38 .38 .38 .38 .56 .38 .56 .38 .38 .56 .56 .75 .38 .56 .38 .56 .56 .75 .75 .56 .56 .75 .75 .56 .75 .75 .75 .75 .75 .75 .94 .97 1.00

7/16 7/16 7/16 7/16 9/16 1/2 9/16 1/2 1/2 9/16 3/4 7/8 5/8 5/8 5/8 5/8 3/4 7/8 1-1/16 13/16 13/16 7/8 1-1/16 7/8 7/8 1-1/16 1-1/16 1-1/16 1-3/8 1-3/8 1-3/8 1-5/8 1-7/8

C L

5MSEL4N 6MSEL2N 6MSEL4N 6MSEL6N 6MSEL8N
W HEX

H R

6MSEL12N 8MSEL4N 8MSEL6N 8MSEL8N 8MSEL12N 10MSEL6N 10MSEL8N 10MSEL12N 12MSEL8N 12MSEL12N 14MSEL12N 16MSEL12N 16MSEL16N 20MSEL20N 24MSEL24N

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

14
Parker Hannifin Corporation

Tube to Male Pipe MSELN
NPT Male Metric Elbow
For metric tube
PARKER PART NO. INTERCHANGES WITH MILLIMETERS TUBE O.D. NPT THREAD C H L R INCH W HEX

M3MSEL1/8N M3MSEL1/4N M4MSEL1/8N M4MSEL1/4N M6MSEL1/8N M6MSEL1/4N M6MSEL3/8N M6MSEL1/2N M8MSEL1/8N M8MSEL1/4N M8MSEL3/8N M8MSEL1/2N M10MSEL1/8N M10MSEL1/4N M10MSEL3/8N M10MSEL1/2N M12MSEL1/4N M12MSEL3/8N M12MSEL1/2N M12MSEL3/4N M15MSEL1/2N M16MSEL3/8N M16MSEL1/2N M16MSEL3/4N M18MSEL1/2N M18MSEL3/4N M20MSEL1/2N M20MSEL3/4N M22MSEL3/4N M25MSEL3/4N M25MSEL1N

3MO-2-2 3MO-2-4 4M0-2-2 4MO-2-4 6MO-2-2 6MO-2-4 6MO-2-6 6MO-2-8 8MO-2-2 8MO-2-4 8MO-2-6 8MO-2-8 10MO-2-8 10MO-2-4 10MO-2-6 10MO-2-8 12MO-2-4 12MO-2-6 12MO-2-8 12MO-2-12 15MO-2-8 16MO-2-6 16MO-2-8 16MO-2-12 18MO-2-8 18MO-2-12 20MO-2-8 20MO-2-12 22MO-2-12 25MO-2-12 25MO-2-16

3 3 4 4 6 6 6 6 8 8 8 8 10 10 10 10 12 12 12 12 15 16 16 16 18 18 20 20 22 25 25

1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/4 3/8 1/2 3/4 1/2 3/8 1/2 3/4 1/2 3/4 1/2 3/4 3/4 3/4 1

23,6 24,6 25,4 26,2 27,0 27,0 29,8 31,8 28,8 28,8 30,6 32,7 31,5 31,5 31,5 33,5 36,0 36,0 36,0 39,8 38,0 38,0 38,0 39,8 39,8 39,8 44,6 44,6 44,6 49,1 49,1

17,8 23,4 18,8 25,4 18,8 23,4 26,2 33,0 19,8 24,4 26,2 33,0 21,6 26,2 26,2 33,0 28,2 28,2 33,0 36,8 35,1 30,2 35,1 36,8 36,8 36,8 41,7 41,7 41,7 41,7 46,5

17,0 18,0 19,2 19,6 19,6 19,6 22,4 24,4 21,3 21,3 23,1 25,2 23,9 23,9 23,9 25,9 25,9 25,9 25,9 29,7 27,9 27,9 27,9 29,7 29,7 29,7 34,5 34,5 34,5 36,8 36,8

9,7 14,2 9,7 14,2 9,7 14,2 14,2 19,0 9,7 14,2 14,2 19,1 9,7 14,2 14,2 19,0 14,2 14,2 19,0 19,0 19,0 14,2 19,0 19,0 19,0 19,0 19,0 19,0 19,0 19,0 23,9

7/16 1/2 1/2 1/2 1/2 1/2 11/16 13/16 9/16 9/16 11/16 13/16 11/16 11/16 11/16 13/16 13/16 13/16 13/16 1-1/16 15/16 15/16 15/16 1-1/16 1-1/16 1-1/16 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

C L

W HEX H R

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

MSELK
BSP Taper Male Elbow
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. BSP TR THREAD C H L R W HEX

4MSEL2K 4MSEL4K 4MSEL6K 4MSEL8K 5MSEL4K 6MSEL4K 6MSEL6K 8MSEL6K 8MSEL8K

400-2-2RT 400-2-4RT 400-2-6RT 400-2-8RT 500-2-4RT 600-2-4RT 600-2-4RT 810-2-6RT 810-2-8RT

1/4 1/4 1/4 1/4 5/16 3/8 3/8 1/2 1/2

1/8 1/4 3/8 1/2 1/4 1/4 3/8 3/8 1/2

1.02 1.08 1.17 1.26 1.17 1.13 1.26 1.35 1.41

.78 .94 1.13 1.31 .82 1.00 1.25 1.25 1.31

.72 .78 .88 .97 .88 .84 .97 .97 1.03

.38 .56 .56 .75 .38 .56 .56 .56 .75

7/16 9/16 3/4 7/8 5/8 9/16 3/4 3/4 7/8

BSP

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

C L

BSP

W HEX

H R

15
Parker Hannifin Corporation

Tube to Male Pipe MSELK
BSP Taper Male Elbow
For metric tube
PARKER PART NO. INTERCHANGES WITH MILLIMETERS TUBE O.D. BSP TR THREAD C H L R INCH W HEX

M3MSEL1/8K M3MSEL1/4K M4MSEL1/8K M4MSEL1/4K M6MSEL1/8K M6MSEL1/4K M6MSEL3/8K M6MSEL1/2K M8MSEL1/8K M8MSEL1/4K M8MSEL3/8K M8MSEL1/2K M10MSEL1/8K M10MSEL1/4K M10MSEL3/8K

3MO-2-2RT 3MO-2-4RT 4MO-2-2RT 4MO-2-4RT 6MO-2-2RT 6MO-2-4RT 6MO-2-6RT 6MO-2-8RT 8MO-2-2RT 8MO-2-4RT 8MO-2-6RT 8MO-2-8RT 10MO-2-2RT 10MO-2-4RT 10MO-2-6RT 10MO-2-8RT 12MO-2-4RT 12MO-2-6RT 12MO-2-8RT 12MO-2-12RT 16MO-2-6RT 16MO-2-8RT 18MO-2-8RT 18MO-2-12RT 20MO-2-12RT 25MO-2-12RT 25MO-2-16RT

3 3 4 4 6 6 6 6 8 8 8 8 10 10 10 10 12 12 12 12 16 16 18 18 20 25 25

1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/4 3/8 1/2 3/4 3/8 1/2 1/2 3/4 3/4 3/4 1

23,6 24,6 25,4 24,6 27,0 27,0 29,8 31,8 28,8 28,8 30,6 32,7 31,5 31,5 31,5 33,5 36,0 36,0 36,0 39,8 38,0 38,0 39,8 39,8 44,6 49,0 49,1

17,8 23,4 18,8 23,4 18,8 23,4 26,2 33,0 19,8 24,4 26,2 33,0 21,6 26,2 26,2 33,0 28,2 28,2 33,0 36,8 30,2 35,1 36,8 36,8 41,7 41,7 46,5

17,0 18,0 18,8 18,8 19,6 19,6 22,4 24,4 21,3 21,3 23,1 25,2 23,9 23,9 23,9 25,9 25,9 25,9 25,9 29,7 27,9 27,9 29,7 29,7 34,5 36,8 36,8

9,7 14,2 9,7 14,2 9,7 14,2 14,2 19,0 9.7 14,2 14,2 19,1 9,7 14,2 14,2 19,0 14,2 14,2 19,0 19,1 14,2 19,0 19,0 19,0 19,0 19,1 23,9

7/16 1/2 1/2 1/2 1/2 1/2 11/16 13/16 9/16 9/16 11/16 13/16 11/16 11/16 11/16 13/16 13/16 13/16 13/16 1-1/16 15/16 15/16 1-1/16 1-1/16 1-3/8 1-3/8 1-3/8

BSP

C L

M10MSEL1/2K M12MSEL1/4K M12MSEL3/8K M12MSEL1/2K M12MSEL3/4K
BSP

W HEX

H R

M16MSEL3/8K M16MSEL1/2K M18MSEL1/2K M18MSEL3/4K M20MSEL3/4K M25MSEL3/4K M25MSEL1K

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

16
Parker Hannifin Corporation

Tube to Male Pipe MVELN
NPT Male 45° Elbow
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD C L P R W HEX

1MVEL1N 2MVEL2N 3MVEL2N 4MVEL2N 4MVEL4N 5MVEL2N 6MVEL2N 6MVEL4N 6MVEL6N 8MVEL6N

100-5-1 200-5-2 300-5-2 400-5-2 400-5-4 500-5-2 600-5-2 600-5-4 600-5-6 810-5-6 1010-5-8 1210-5-8 1410-5-8 1610-5-8

1/16 1/8 3/16 1/4 1/4 5/16 3/8 3/8 3/8 1/2 5/8 3/4 7/8 1

1/16 1/8 1/8 1/8 1/4 1/8 1/8 1/4 3/8 3/8 1/2 3/4 3/4 1

.43 .60 .64 .70 .70 .73 .76 .76 .76 .87 .87 .87 .87 1.05

.468 .59 .56 .63 .66 .66 .72 .72 .75 .75 .81 .84 1.36 1.19

.569 .66 .58 .66 .86 .66 .67 .86 .95 .95 1.17 1.20 1.27 1.48

.38 .38 .38 .38 .56 .38 .38 .56 .56 .56 .75 .75 .75 .94

3/8 7/16 7/16 9/16 9/16 9/16 9/16 9/16 3/4 3/4 7/8 1-1/16 1-5/16 1-5/16

L C W HEX

10MVEL8N 12MVEL12N 14MVEL12N 16MVEL16N

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

P

R

MVELN
NPT Male 45° Elbow
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. NPT PIPE THREAD C L P R W HEX

M6MVEL1/8N M6MVEL1/4N M8MVEL1/8N M10MVEL1/4N M12MVEL3/8N M12MVEL1/2N M16MVEL1/2N

– – – – – – –

6 6 8 10 12 12 16

1/8 1/4 1/8 1/4 3/8 1/2 1/2

17,7 17,7 18,6 19,5 22,0 22,0 22,0

16,0 16,0 16,8 19,0 19,0 20,6 20,6

16,8 21,8 16,8 24,1 24,1 29,7 29,7

9,5 14,3 9,5 14,3 14,3 19,0 19,0

14,0 14,0 14,0 19,0 19,0 22,0 22,0

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

L C W HEX

P

R

17
Parker Hannifin Corporation

Tube to Male Pipe MRTN
NPT Male Run Tee
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD A C H L R W HEX

2MRT2N 2MBT4N 3MRT2N 4MRT2N 4MRT4N 5MRT2N 5MRT4N 6MRT4N 6MRT6N 8MRT6N 8MRT8N 10MRT8N 12MRT12N 14MRT12N 16MRT12N 16MRT16N
H R

200-3-2TMT 200-3-4TMT 300-3-2TMT 400-3-2TMT 400-3-4TMT 500-3-2TMT 500-3-4TMT 600-3-4TMT 600-3-6TMT 810-3-6TMT 810-3-8TMT 1010-3-8TMT 1210-3-12TMT 1410-3-12TMT 1610-3-12TMT 1610-3-16TMT

1/8 1/8 3/16 1/4 1/4 5/16 5/16 3/8 3/8 1/2 1/2 5/8 3/4 7/8 1 1

1/8 1/4 1/8 1/8 1/4 1/8 1/4 1/4 3/8 3/8 1/2 1/2 3/4 3/4 3/4 1

1.67 1.98 1.74 1.80 2.07 2.00 2.18 2.21 2.43 2.82 2.74 2.81 3.06 3.26 3.60 3.78

.92 .98 1.00 1.06 1.07 1.17 1.17 1.20 1.31 1.42 1.43 1.43 1.56 1.76 1.94 1.94

.71 1.00 .74 .74 1.00 .82 1.01 1.01 1.12 1.12 1.31 1.38 1.50 1.50 1.66 1.84

.66 .72 .74 .77 .78 .88 .88 .91 1.02 1.02 1.03 1.03 1.16 1.36 1.45 1.45

.38 .56 .38 .38 .56 .38 .56 .56 .56 .56 .75 .75 .75 .75 .75 .94

5/16 1/2 1/2 1/2 9/16 5/8 5/8 5/8 13/16 13/16 7/8 7/8 1-1/16 1-5/16 1-5/16 1-3/8

A C L

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

W HEX

MRTN
NPT Male Run Tee
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. NPT THREAD A C H L R

INCH W HEX

M6MRT1/8N M6MRT1/4N M8MRT1/8N M8MRT1/4N M10MRT1/4N

6MO-3-2TMT 6MO-3-4TMT 8MO-3-2TMT 8MO-3-4TMT 10MO-3-4TMT

6 6 8 8 10 10 12 12 12 16

1/8 1/4 1/8 1/4 1/4 1/2 1/4 3/8 1/2 1

45,8 50,3 50,7 55,3 61,7 66,5 64,2 64,2 69,0 93,1

27,0 27,0 29,9 29,9 33,5 33,5 36,0 36,0 36,0 46,6

18,0 23,4 20,8 25,4 28,2 33,0 28,2 28,2 33,0 46,5

19,6 19,6 22,4 22,4 25,9 25,9 25,9 25,9 25,9 34,4

9,7 14,2 9,7 14,2 14,2 19,0 14,2 14,2 19,0 23,9

1/2 1/2 5/8 5/8 13/16 13/16 13/16 13/16 13/16 1-3/8

M10MRT1/2N 10MO-3-8TMT M12MRT1/4N 12MO-3-4TMT M12MRT3/8N 12MO-3-6TMT M12MRT1/2N 12MO-3-8TMT M16MRT1N 16MO-3-16TMT

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

A C L H R

W HEX

18
Parker Hannifin Corporation

Tube to Male Pipe MBTN
NPT Male Branch Tee
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD A C H L R W HEX

2MBT2N 2MBT4N 3MBT2N 4MBT2N 4MBT4N 5MBT2N 5MBT4N 6MBT4N 6MBT6N 8MBT6N 8MBT8N 10MBT8N 12MBT12N 14MBT12N 16MBT12N 16MBT16N

200-3-2TTM 200-3-4TTM 300-3-2TTM 400-3-2TTM 400-3-4TTM 500-3-2TTM 500-3-4TTM 600-3-4TTM 600-3-6TTM 810-3-6TTM 810-3-8TTM 1010-3-8TTM 1210-3-12TTM 1410-3-12TTM 1610-3-12TTM 1610-3-16TTM

1/8 1/8 3/16 1/4 1/4 5/16 5/16 3/8 3/8 1/2 1/2 5/8 3/4 7/8 1 1

1/8 1/4 1/8 1/8 1/4 1/8 1/4 1/4 3/8 3/8 1/2 1/2 3/4 3/4 3/4 1

1.84 1.96 2.00 2.12 2.14 2.34 2.34 2.40 2.62 2.84 2.86 2.86 3.12 3.52 3.88 3.88

.92 .98 1.00 1.06 1.07 1.17 1.17 1.20 1.31 1.42 1.43 1.43 1.56 1.76 1.94 1.94

.71 1.00 .74 .74 1.00 .82 1.01 1.01 1.12 1.12 1.31 1.31 1.50 1.50 1.66 1.84

.66 .72 .74 .77 .78 .88 .88 .91 1.02 1.02 1.03 1.03 1.16 1.36 1.45 1.45

.38 .56 .38 .38 .56 .38 .56 .56 .56 .56 .75 .75 .75 .75 .75 .94

7/16 9/16 1/2 1/2 9/16 5/8 5/8 5/8 13/16 13/16 7/8 7/8 1-1/16 1-3/8 1-3/8 1-3/8

A C L

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

W HEX R

H

MBTN
NPT Male Branch Tee
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. NPT THREAD A C H L R

INCH W HEX

M6MBT1/8N M6MBT1/4N M8MBT1/8N M8MBT1/4N M10MBT1/4N M10MBT3/8N M12MBT1/4N M12MBT3/8N M12MBT1/2N M16MBT1/2N

6MO-3TTM 6MO-3-4TTM 8MO-3TTM 8MO-3-4TTM 10MO-3-4TTM 10MO-3-6TTM 12MO-3-4TTM 12MO-3-6TTM 12MO-3-8TTM 16MO-3-8TTM

6 6 8 8 10 10 12 12 12 16

1/8 1/4 1/8 1/4 1/4 3/8 1/4 3/8 1/2 1/2

53,9 53,9 59,7 59,7 67,0 67,0 72,0 72,0 72,0 77,6

27,0 27,0 29,9 29,9 33,5 33,5 36,0 36,0 36,0 38,8

18,8 23,4 20,8 25,4 28,2 28,2 28,2 28,2 33,0 35,8

19,6 19,6 22,4 22,4 25,9 25,9 25,9 25,9 25,9 28,7

9,7 14,2 9,7 14,2 14,2 14,2 14,2 14,2 19,0 19,1

1/2 1/2 5/8 5/8 13/16 13/16 13/16 13/16 13/16 1

NOTE: A and C dimensions are typical finger-tight. A C L

Dimensions for reference only, subject to change.

W HEX R

H

19
Parker Hannifin Corporation

Tube to Female Pipe FSCN
NPT Female Connector
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD A C D W HEX

1FSC1N 1FSC2N 2FSC2N 2FSC4N 3FSC2N 3FSC4N 4FSC2N 4FSC4N 4FSC6N 4FSC8N 5FSC2N 5FSC4N 5FSC6N 6FSC2N 6FSC4N

100-7-1 100-7-2 200-7-2 200-7-4 300-7-2 300-7-4 400-7-2 400-7-4 400-7-6 400-7-8 500-7-2 500-7-4 500-7-6 600-7-2 600-7-4 600-7-6 600-7-8 600-7-12 810-7-4 810-7-6 810-7-8 810-7-12 1010-7-6 1010-7-8 1010-7-12 1210-7-8 1210-7-12 1410-7-12 1610-7-12 1610-7-16 2010-7-20 2410-7-24 3210-7-32

1/16 1/16 1/8 1/8 3/16 3/16 1/4 1/4 1/4 1/4 5/16 5/16 5/16 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 5/8 5/8 5/8 3/4 3/4 7/8 1 1 1-1/4 1-1/2 2

1/16 1/8 1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/8 1/4 3/8 1/2 3/4 1/4 3/8 1/2 3/4 3/8 1/2 3/4 1/2 3/4 3/4 3/4 1 1-1/4 1-1/2 2

.93 .95 1.14 1.32 1.17 1.35 1.23 1.42 1.48 1.67 1.27 1.46 1.29 1.48 1.54 1.73 1.85 1.59 1.65 1.84 1.96 1.65 1.84 1.96 1.84 1.96 1.96 2.15 2.46 2.94 3.28 4.00

.43 .43 .60 .60 .64 .64 .70 .70 .70 .70 .73 .73 .73 .76 .76 .76 .76 .76 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 1.05 1.05 1.52 1.77 2.47

.78 .81 .88 1.06 .91 1.09 .94 1.13 1.19 1.38 .97 1.16 1.219 1.00 1.19 1.25 1.44 1.56 1.19 1.25 1.44 1.56 1.25 1.44 1.56 1.44 1.56 1.56 1.66 1.97 2.08 2.22 2.53

7/16 9/16 9/16 3/4 9/16 3/4 9/16 3/4 7/8 1-1/16 9/16 3/4 7/8 5/8 3/4 7/8 1-1/16 1-1/4 13/16 7/8 1-1/16 1-1/4 15/16 1-1/16 1-3/8 1-1/16 1-3/8 1-3/8 1-3/8 1-5/8 2 2-3/8 2-7/8

A C W HEX

D

6FSC6N 6FSC8N 6FSC12N 8FSC4N 8FSC6N 8FSC8N 8FSC12N 10FSC6N 10FSC8N 10FSC12N 12FSC8N 12FSC12N 14FSC12N 16FSC12N 16FSC16N 20FSC20N 24FSC24N 32FSC32N

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

FSCN
NPT Female Connector
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. NPT THREAD A C D W HEX

M3FSC1/8N M3FSC1/4N M4FSC1/8N M6FSC1/8N M6FSC1/4N M6FSC3/8N M6FSC1/2N M8FSC1/8N M8FSC1/4N M8FSC3/8N M10FSC1/4N M10FSC3/8N M10FSC1/2N M12FSC1/4N M12FSC3/8N

3MO-7-2 3MO-7-4 4MO-7-2 6MO-7-2 6MO-7-4 6MO-7-6 6MO-7-8 8MO-7-2 8MO-7-4 8MO-7-6 10MO-7-4 10MO-7-6 10MO-7-8 12MO-7-4 12MO-7-6 12MO-7-8 16MO-7-6 16MO-7-8 20MO-7-8 20MO-7-12 22MO-7-12 25MO-7-12 25MO-7-16

3 3 4 6 6 6 6 8 8 8 10 10 10 12 12 12 16 16 20 20 22 25 25

1/8 1/4 1/8 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/4 3/8 1/2 1/4 3/8 1/2 3/8 1/2 1/2 3/4 3/4 3/4 1

28,8 33,6 29,6 31,3 36,1 37,7 42,5 32,1 36,9 38,5 37,8 39,4 44,1 41,9 41,9 46,6 41,9 46,9 47,9 49,7 49,7 53,6 62,3

15,3 15,3 16,1 17,7 17,7 17,7 17,7 18,6 18,6 18,6 19,5 19,5 19,5 22,0 22,0 22,0 22,0 22,0 22,0 22,0 22,0 26,5 26,5

22,2 27,0 23,0 23,8 28,6 30,2 35,0 24,6 29,4 31,0 30,2 31,8 36,5 31,8 31,8 36,5 31,8 36,5 37,8 39,6 39,6 41,3 50,0

14,0 19,0 14,0 14,0 19,0 22,0 27,0 14,0 19,0 22,0 19,0 22,0 27,0 22,0 22,0 27,0 27,0 27,0 30,0 35,0 35,0 35,0 41,0

A C W HEX

D

M12FSC1/2N M16FSC3/8N M16FSC1/2N M20FSC1/2N M20FSC3/4N M22FSC3/4N M25FSC3/4N M25FSC1N

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

20
Parker Hannifin Corporation

Tube to Female Pipe FSCK
BSP Taper Female Connector
For fractional tube
BSP

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. BSPT THREAD A C D W HEX BORE

4FSC2K 4FSC4K 4FSC6K 4FSC8K 6FSC4K 6FSC6K 6FSC8K 8FSC4K 8FSC6K 8FSC8K

400-7-2RT 400-7-4RT 400-7-6RT 400-7-8RT 600-7-4RT 600-7-6RT 600-7-8RT 810-7-4RT 810-7-6RT 810-7-8RT

1/4 1/4 1/4 1/4 3/8 3/8 3/8 1/2 1/2 1/2

1/8 1/4 3/8 1/2 1/4 3/8 1/2 1/4 3/8 1/2

1.24 1.42 1.49 1.68 1.48 1.54 1.73 1.59 1.65 1.84

.70 .70 .70 .70 .76 .76 .76 .87 .87 .87

.94 1.13 1.19 1.38 1.19 1.25 1.44 1.19 1.25 1.44

9/16 3/4 7/8 1-1/16 3/4 7/8 1-1/16 13/16 7/8 1-1/16

.19 .19 .19 .19 .28 .28 .28 .406 .406 .406

A C W HEX

Dimensions for reference only, subject to change.

BSP

D

FSCK
BSP Taper Female Connector
For metric tube
BSP

PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. BSPT THREAD A C D W HEX

M3FSC1/8K M6FSC1/8K M6FSC1/4K M6FSC3/8K M6FSC1/2K M8FSC1/8K M8FSC1/4K M8FSC3/8K M8FSC1/2K M10FSC1/8K M10FSC1/4K M10FSC3/8K M10FSC1/2K M12FSC1/4K M12FSC3/8K M12FSC1/2K M16FSC1/2K M20FSC1/2K M20FSC3/4K M22FSC1K M25FSC3/4K M25FSC1K

3MO-7-2RT 6MO-7-2RT 6MO-7-4RT 6MO-7-6RT 6MO-7-8RT 8MO-7-2RT 8MO-7-4RT 8MO-7-6RT 8MO-7-8RT 10MO-7-2RT 10MO-7-4RT 10MO-7-6RT 10MO-7-8RT 12MO-7-4RT 12MO-7-6RT 12MO-7-8RT 16MO-7-8RT 20MO-7-8RT 20MO-7-12RT 22MO-7-16RT 25MO-7-12RT 25MO-7-16RT

3 6 6 6 6 8 8 8 8 10 10 10 10 12 12 12 16 20 20 22 25 25

1/8 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/4 3/8 1/2 1/2 1/2 3/4 1 3/4 1

29,2 31,3 35,8 37,6 42,5 32,8 37,0 38,5 43,3 33,0 37,8 39,4 44,2 40,3 41,9 46,7 48,4 54,7 49,7 57,9 54,3 61,5

15,3 17,7 17,7 17,7 17,7 18,6 18,6 18,6 18,6 19,5 19,5 19,5 19,5 22,0 22,0 22,0 22,0 22,0 22,0 22,0 26,5 26,5

22,6 23,8 28,3 30,1 35,0 25,3 29,5 31,0 35,8 25,4 30,2 31,8 36,6 30,2 31,8 36,6 38,3 44,6 39,6 47,8 42,1 49,3

14,0 14,0 19,0 22,0 27,0 15,0 19,0 22,0 27,0 18,0 19,0 22,0 27,0 22,0 22,0 27,0 18,0 30,0 35,0 41,0 35,0 41,0

A C W HEX

BSP

D

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

21
Parker Hannifin Corporation

Tube to Female Pipe FBCN
NPT Female Bulkhead Connector
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD A C D L W HEX

2FBC2N 3FBC2N 4FBC2N 4FBC4N 5FBC2N 5FBC8N 6FBC4N 8FBC6N 8FBC8N 10FBC8N

200-71-2 300-71-2 400-71-2 400-71-4 500-71-2 500-71-8 600-71-4 810-71-6 810-71-8 1010-71-8 1210-71-12 1410-71-12 1610-71-16

1/8 3/16 1/4 1/4 5/16 5/16 3/8 1/2 1/2 5/8 3/4 7/8 1

1/8 1/8 1/8 1/4 1/8 1/2 1/4 3/8 1/2 1/2 3/4 3/4 1

1.76 1.79 1.85 2.04 1.96 2.38 2.17 2.43 2.62 2.65 2.90 3.18 3.68

1.23 1.26 1.31 1.31 1.42 1.42 1.44 1.65 1.65 1.68 1.87 2.09 2.27

1.50 1.53 1.56 1.75 1.66 2.08 1.88 2.03 2.22 2.25 2.50 2.78 3.19

.97 1.00 1.02 1.02 1.12 1.12 1.15 1.25 1.25 1.28 1.47 1.69 1.78

9/16 9/16 5/8 3/4 11/16 1-1/16 3/4 15/16 1-1/16 1-1/16 1-3/8 1-3/8 1-5/8

A C W HEX

12FBC12N 14FBC12N 16FBC16N

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. For bulkhead hole drill size and maximum bulkhead thickness, see Page 28, Part BC. L D

FBCN
NPT Female Bulkhead Connector
For metric tube
PARKER PART NO. INTERCHANGES WITH TUBE O.D. NPT THREAD A C

MILLIMETERS B’HEAD HOLE MAX. DRILL B’HEAD SIZE THICK.

D

L

W HEX

M6FBC1/8N M6FBC1/4N M8FBC1/8N M10FBC1/4N M12FBC3/8N M12FBC1/2N

6MO-71-2 6MO-71-4 8MO-71-2 10MO-71-4 12MO-71-6 12MO-71-8

6 6 8 10 12 12

1/8 1/4 1/8 1/4 3/8 1/2

47,2 52,0 49,6 55,2 60,9 66,4

33,7 33,7 36,1 37,0 41,9 41,9

39,7 44,5 42,1 47,6 50,8 56,3

26,2 26,2 28,5 29,4 31,8 31,8

16,0 19,0 18,0 19,0 24,0 27,0

11,5 11,5 13,1 16,3 19,5 19,5

10,2 10,2 11,2 11,2 12,7 12,7

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. For bulkhead hole drill size and maximum bulkhead thickness, see Page 28, Part BC. A C W HEX

L D

GCR
BSPP Gauge Connector
For fractional tube
BSPP

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. BSPP THREAD A C D W HEX BORE

4FSC4GC 4FSC6GC 4FSC8GC 5FSC4GC 5FSC8GC 6FSC4GC 6FSC6GC 6FSC8GC 8FSC4GC 8FSC6GC 8FSC8GC

400-7-4RG 400-7-6RG 400-7-8RG 500-7-4RG 500-7-8RG 600-7-4RG 600-7-6RG 600-7-8RG 810-7-4RG 810-7-6RG 810-7-8RG

1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 1/2 1/2 1/2

1/4 3/8 1/2 1/4 1/2 1/4 3/8 1/2 1/4 3/8 1/2

1.48 1.48 1.70 1.51 1.59 1.55 1.55 1.63 1.65 1.75 1.90

.70 .70 .70 .73 .73 .76 .76 .76 .86 .86 .86

1.19 1.19 1.41 1.22 1.30 1.25 1.25 1.33 1.25 1.35 1.50

3/4 7/8 1-1/16 3/4 1-1/16 3/4 7/8 1-1/16 13/16 7/8 1-1/16

.19 .19 .19 .21 .28 .21 .26 .28 .21 .26 .28

A C W HEX

NOTE: A and C dimensions are typical finger-tight. See Catalog 4260 Pipe/ISO Fittings for detailed information. Sealing Washer on page 72 to be used with this fitting.

Dimensions for reference only, subject to change.

BSPP

D

22
Parker Hannifin Corporation

Tube to Female Pipe GCR
BSPP Gauge Connector
For metric tube
BSPP

PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. BSPP THREAD A C D W HEX

M3GC1/4R M6GC1/4R M6GC3/8R M6GC1/2R M8GC1/4R M8GC3/8R M8GC1/2R M10GC1/4R M10GC3/8R M10GC1/2R M12GC1/4R M12GC3/8R M12GC1/2R

3MO-7-4RG 6MO-7-4RG 6MO-7-6RG 6MO-7-8RG 8MO-7-4RG 8MO-7-6RG 8MO-7-8RG 10MO-7-4RG 10MO-7-6RG 10MO-7-8RG 12MO-7-4RG 12MO-7-6RG 12MO-7-8RG

3 6 6 6 8 8 8 10 10 10 12 12 12

1/4 1/4 3/8 1/2 1/4 3/8 1/2 1/4 3/8 1/2 1/4 3/8 1/2

35,3 37,7 37,7 43,2 38,5 40,8 44,0 39,4 38,8 41,3 41,9 44,4 48,2

15,3 17,7 17,7 17,7 18,6 18,6 18,6 19,5 19,5 19,5 22,0 22,0 22,0

28,7 30,2 30,2 35,7 31,0 33,3 36,5 31,8 31,2 33,7 31,8 34,3 38,1

19,0 19,0 22,0 27,0 19,0 22,0 27,0 19,0 22,0 27,0 22,0 22,0 27,0

A C W HEX

NOTE: A and C dimensions are typical finger-tight. See Catalog 4260 Pipe/ISO Fittings for detailed information. Sealing Washer on page 72 to be used with this fitting.

Dimensions for reference only, subject to change.

BSPP

D

FELN
NPT Female Elbow
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. NPT PIPE THREAD C H L W HEX

1FEL1N 1FEL2N 2FEL2N 2FEL4N 3FEL2N 4FEL2N 4FEL4N 4FEL6N 4FEL8N 5FEL2N

100-8-1 100-8-2 200-8-2 200-8-4 300-8-2 400-8-2 400-8-4 400-8-6 400-8-8 500-8-2 500-8-4 600-8-2 600-8-4 600-8-6 600-8-8 810-8-4 810-8-6 810-8-8 1010-8-6 1010-8-8 1210-8-8 1210-8-12 1410-8-12 1610-8-12 1610-8-16

1/16 1/16 1/8 1/8 3/16 1/4 1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 5/8 3/4 3/4 7/8 1 1

1/16 1/8 1/8 1/4 1/8 1/8 1/4 3/8 1/2 1/8 1/4 1/8 1/4 3/8 1/2 1/4 3/8 1/2 3/8 1/2 1/2 3/4 3/4 3/4 1

.71 .81 .98 1.10 1.01 1.07 1.20 1.26 1.35 1.17 1.24 1.20 1.26 1.32 1.42 1.42 1.43 1.53 1.43 1.53 1.56 1.65 1.76 1.94 2.02

.56 .75 .75 .88 .75 .75 .88 .88 1.13 .75 .88 .75 .88 .88 1.13 .88 .88 1.13 .88 1.13 1.13 1.25 1.25 1.25 1.50

.56 .66 .72 .84 .75 .78 .91 .97 1.06 .88 .94 .91 .97 1.03 1.13 1.02 1.03 1.13 1.03 1.13 1.16 1.36 1.36 1.45 1.53

7/16 9/16 9/16 3/4 9/16 9/16 3/4 7/8 1-1/16 5/8 3/4 5/8 3/4 7/8 1-1/16 13/16 7/8 1-1/16 7/8 1-1/16 1-1/16 1-3/8 1-3/8 1-3/8 1-5/8

C L W HEX

5FEL4N 6FEL2N 6FEL4N 6FEL6N 6FEL8N 8FEL4N 8FEL6N 8FEL8N 10FLE6N 10FEL8N 12FEL8N 12FEL12N 14FEL12N 16FEL12N 16FEL16N

H

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

FELN
NPT Female Elbow
For metric tube
C L W HEX PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. NPT THREAD C H L

INCH W HEX

M6FEL1/8N M6FEL1/4N M8FEL1/8N M8FEL1/4N M10FEL1/4N M10FEL3/8N M10FEL1/2N M12FEL1/4N M12FEL3/8N M12FEL1/2N M16FEL3/8N M16FEL1/2N

6MO-8-2 6MO-8-4 8MO-8-2 8MO-8-4 10MO-8-4 10MO-8-6 10MO-8-8 12MO-8-4 12MO-8-6 12MO-8-8 16MO-8-6 16MO-8-8

6 6 8 8 10 10 10 12 12 12 16 16

1/8 1/4 1/8 1/4 1/4 3/8 1/2 1/4 3/8 1/2 3/8 1/2

27,0 29,8 28,8 30,6 33,5 33,5 36,3 36,0 36,0 38,8 39,5 39,5

19,0 22,4 19,1 22,4 22,4 22,4 28,5 22,4 22,4 28,4 23,6 28,4

19,6 22,4 21,3 23,1 25,9 25,9 28,7 25,9 25,9 28,7 29,7 29,7

1/2 11/16 9/16 11/16 13/16 13/16 1 13/16 13/16 1 1-1/16 1-1/16

H

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

23
Parker Hannifin Corporation

Tube to Female Pipe FRTN
NPT Female Run Tee
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD A C H L W HEX

2FRT2N 3FRT2N 4FRT2N 4FRT4N 5FRT2N 6FRT4N 8FRT4N 8FRT6N 8FRT8N 10FRT8N 12FRT12N 14FRT8N 14FRT12N 16FRT12N 16FRT16N

200-3-2TFT 300-3-2TFT 400-3-2TFT 400-3-4TFT 500-3-2TFT 600-3-4TFT 810-3-4TFT 810-3-6TFT 810-3-8TFT 1010-3-8TFT 1210-3-12TFT 1410-3-8TFT 1410-3-12TFT 1610-3-12TFT 1610-3-16TFT

1/8 3/16 1/4 1/4 5/16 3/8 1/2 1/2 1/2 5/8 3/4 7/8 7/8 1 1

1/8 1/8 1/8 1/4 1/8 1/4 1/2 3/8 1/2 1/2 3/4 1/2 3/4 3/4 1

1.76 1.76 1.82 2.08 1.92 2.14 2.56 2.34 2.66 2.66 2.90 3.01 3.01 3.19 3.52

1.01 1.01 1.07 1.20 1.17 1.26 1.43 1.43 1.53 1.53 1.65 1.76 1.76 1.94 2.02

.75 .75 .75 .88 .75 .88 1.13 .91 1.13 1.13 1.25 1.25 1.25 1.25 1.50

.75 .75 .78 .91 .88 .97 1.13 1.03 1.13 1.13 1.36 1.36 1.36 1.45 1.53

9/16 9/16 9/16 3/4 5/8 3/4 13/16 7/8 1-1/16 1-1/16 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

A C L H

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

W HEX

FRTN
NPT Female Run Tee
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. NPT THREAD A C H L

INCH W HEX

M6FRT1/8N M6FRT1/4N M8FRT1/8N M10FRT1/4N M12FRT1/4N M12FRT3/8N M12FRT1/2N M16FRT1/2N

6MO-3TFT 6MO-3-4TFT 8MO-3TFT 10MO-3TFT 12MO-3-4TFT 12MO-3TFT 12MO-3-8TFT 16MO-3TTF

6 6 8 10 12 12 12 16

1/8 1/4 1/8 1/4 1/4 3/8 1/2 1/2

46,0 52,1 48,9 55,9 58,4 58,4 67,3 68,2

27,0 29,8 29,9 33,5 36,0 36,0 38,8 39,8

19,0 22,4 19,0 22,4 22,4 22,4 28,5 28,4

19,6 22,4 22,4 25,9 25,9 25,9 28,7 29,7

1/2 11/16 5/8 13/16 13/16 13/16 1 1-1/16

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

A C L H

W HEX

24
Parker Hannifin Corporation

Tube to Female Pipe FBTN
NPT Female Branch Tee
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. NPT PIPE THREAD A C H L W HEX

2FBT2N 3FBT2N 4FBT2N 4FBT4N 5FBT2N 6FBT4N 8FBT4N 8FBT6N 8FBT8N 10FBT8N 12FBT12N 14FBT12N 16FBT12N 16FBT16N

200-3-2TTF 300-3-2TTF 400-3-2TTF 400-3-4TTF 500-3-2TTF 600-3-4TTF 810-3-4TTF 810-3-6TTF 810-3-8TTF 1010-3-8TTF 1210-3-12TTF 1410-3-12TTF 1610-3-12TTF 1610-3-16TTF

1/8 3/16 1/4 1/4 5/16 3/8 1/2 1/2 1/2 5/8 3/4 7/8 1 1

1/8 1/8 1/8 1/4 1/8 1/4 1/4 3/8 1/2 1/2 3/4 3/4 3/4 1

2.02 2.02 2.14 2.40 2.34 2.52 2.86 2.86 3.06 3.06 3.30 3.52 3.88 4.04

1.01 1.01 1.07 1.20 1.17 1.26 1.43 1.43 1.53 1.53 1.65 1.76 1.94 2.02

.75 .75 .75 .88 .75 .88 .88 .91 1.13 1.13 1.25 1.25 1.25 1.50

.75 .75 .78 .91 .88 .97 1.02 1.03 1.13 1.13 1.36 1.36 1.45 1.53

9/16 9/16 9/16 3/4 5/8 3/4 13/16 7/8 1-1/16 1-1/16 1-3/8 1-3/8 1-3/8 1-3/8

A C L

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

H W HEX

FBTN
NPT Female Branch Tee
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. NPT THREAD A C H L

INCH W HEX

M6FBT1/8N M6FBT1/4N M8FBT1/8N M10FBT1/4N M12FBT1/8N M12FBT1/4N M12FBT3/8N M12FBT1/2N M16FBT1/2N

6MO-3TTF 6MO-3-4TTF 8MO-3TTF 10MO-3TTF 12MO-3TTF 12MO-3-4TTF 12MO-3TTF 12MO-3-8TTF 16MO-3TTF

6 6 8 10 12 12 12 12 16

1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/2

53,9 59,5 59,7 67,0 72,0 72,0 72,0 77,6 77,6

27,0 29,8 29,9 33,5 36,0 36,0 36,0 38,8 38,8

19,0 22,4 19,0 22,4 22,3 22,3 22,4 28,5 28,4

19,6 22,4 22,4 25,9 25,9 25,9 25,9 28,7 28,7

1/2 11/16 5/8 13/16 13/16 13/16 13/16 1 1

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

A C L

H W HEX

25
Parker Hannifin Corporation

Tube to Tube Unions SC
Union
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. A C D W HEX

1SC1 2SC2 3SC3 4SC4 5SC5 6SC6 8SC8 10SC10 12SC12 14SC14 16SC16 20SC20 24SC24 32SC32

100-6 200-6 300-6 400-6 500-6 600-6 810-6 1010-6 1210-6 1410-6 1610-6 2010-6 2410-6 3210-6

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2

.99 1.39 1.48 1.62 1.70 1.77 2.02 2.05 2.11 2.18 2.57 3.61 4.23 5.88

.43 .60 .64 .70 .73 .76 .87 .87 .87 .87 1.05 1.52 1.77 2.47

.69 .88 .95 1.03 1.11 1.19 1.22 1.25 1.31 1.38 1.59 1.89 2.11 2.94

5/16 7/16 7/16 1/2 9/16 5/8 13/16 15/16 1-1/16 1-3/16 1-3/8 1-3/4 2-1/8 2-3/4

A C

NOTE: A and C dimensions are typical finger-tight. W HEX D

Dimensions for reference only, subject to change.

SCM
Union
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. A C D W HEX

SCM2 SCM3 SCM4 SCM6 SCM8 SCM10 SCM12 SCM14 SCM15 SCM16 SCM18 SCM20 SCM22 SCM25

2MO-6 3MO-6 4MO-4 6MO-6 8MO-6 10MO-6 12MO-6 14MO-6 15MO-6 16MO-6 18MO-6 20MO-6 22MO-6 25MO-6

2 3 4 6 8 10 12 14 15 16 18 20 22 25

35,6 35,3 37,4 41,2 43,2 46,2 51,2 52,0 52,0 52,0 53,5 55,0 55,0 65,1

15,3 15,3 16,1 17,7 18,6 19,5 22,0 22,0 22,0 22,0 22,0 22,0 22,0 26,5

22,4 22,1 24,2 26,2 28,2 31,0 31,0 31,8 31,8 31,8 33,3 34,8 34,8 40,5

12,0 12,0 12,0 14,0 15,0 18,0 22,0 24,0 24,0 24,0 27,0 30,0 30,0 35,0

A C

W HEX D

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

CU
Conversion Union
For metric tube
Metric Tube to Inch Tube
PARKER PART NO.

INTERCHANGES WITH

TUBE O.D. T1 MM T2 INCH A C1

MILLIMETERS C2 D W HEX

M3CU2 M4CU2 M4CU4 M6CU2 M6CU4 M6CU5 M8CU4 M8CU6 M10CU2 M10CU4

3MO-6-2 4MO-6-2 4MO-6-4 6MO-6-2 6MO-6-4 6MO-6-5 8MO-6-4 8MO-6-6 10MO-6-2 10MO-6-4 10MO-6-6 12MO-6-6 12MO-6-8 15MO-6-8 16MO-6-6 18MO-6-12

3 4 4 6 6 6 8 8 10 10 10 12 12 15 16 18

1/8 1/8 1/4 1/8 1/4 5/16 1/4 6 1/8 1/4 3/8 3/8 1/2 1/2 3/8 3/4

36,3 36,5 39,3 38,5 41,1 42,3 42,3 44,0 41,8 44,5 46,0 48,4 51,1 52,0 52,0 53,5

15,3 16,1 16,1 17,7 17,7 17,7 18,6 18,6 19,5 19,5 19,5 22,0 22,0 22,0 22,0 22,0

15,3 15,3 17,7 15,3 17,7 18,8 17,7 19,3 15,3 17,7 19,3 19,3 21,8 21,8 19,3 21,8

22,6 23,6 26,4 24,6 25,9 27,2 27,2 29,1 27,9 29,2 30,7 30,7 31,0 32,0 34,3 33,5

12,0 12,0 14,0 14,0 14,0 14,0 15,0 15,0 18,0 18,0 18,0 22,0 22,0 24,0 24,0 27,0

A C1 C2

M10CU6 M12CU6 M12CU8 M15CU8 M16CU6 M18CU12
T2

T1 W HEX D

NOTE: A, C1 and C2 dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

26
Parker Hannifin Corporation

Tube to Tube Unions RU
Reducing Union
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES T1 TUBE O.D. T2 TUBE O.D. A D C1 C2 W HEX

2RU1 3RU1 3RU2 4RU1 4RU2 4RU3 5RU2 5RU4 6RU1 6RU2 6RU4 6RU5 8RU2 8RU4 8RU6 10RU6 10RU8 12RU4 12RU6 12RU8 12RU10 16RU8 16RU12

200-6-1 300-6-1 300-6-2 400-6-1 400-6-2 400-6-3 500-6-2 500-6-4 600-6-1 600-6-2 600-6-4 600-6-5 810-6-2 810-6-4 810-6-6 1010-6-6 1010-6-8 1210-6-4 1210-6-6 1210-6-8 1210-6-10 1610-6-8 1610-6-12

1/8 3/16 3/16 1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 5/8 3/4 3/4 3/4 3/4 1 1

1/16 1/16 1/8 1/16 1/8 3/16 1/8 1/4 1/16 1/8 1/4 5/16 1/8 1/4 3/8 3/8 1/2 1/4 3/8 1/2 5/8 1/2 3/4

1.21 1.27 1.44 1.38 1.52 1.55 1.58 1.67 1.44 1.61 1.71 1.75 1.75 1.85 1.91 1.94 2.05 1.95 2.00 2.11 2.11 2.39 2.39

.81 .86 .92 .91 .97 1.00 1.03 1.08 1.00 1.06 1.13 1.16 1.09 1.16 1.22 1.25 1.25 1.25 1.31 1.31 1.31 1.50 1.50

.60 .64 .64 .70 .70 .70 .73 .73 .76 .76 .76 .76 .87 .87 .87 .87 .87 .87 .87 .87 .87 1.05 1.05

.43 .43 .60 .43 .60 .64 .60 .70 .43 .60 .70 .73 .60 .70 .76 .76 .87 .76 .76 .87 .87 .87 .87

7/16 7/16 7/16 1/2 1/2 1/2 9/16 9/16 5/8 5/8 5/8 5/8 13/16 13/16 13/16 15/16 15/16 1-1/16 1-1/16 1-1/16 1-1/16 1-3/8 1-3/8

A C1 C2

T1 W HEX D

T2

NOTE: A, C1 and C2 dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

RUM
Reducing Union
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS T1 TUBE O.D. T2 TUBE O.D. A C1 C2 D W HEX

M3RUM2 M6RUM2 M6RUM3 M6RUM4 M8RUM6 M10RUM6 M10RUM8 M12RUM6 M12RUM8 M12RUM10 M16RUM10 M16RUM12 M18RUM12 M25RUM18 M25RUM20

3M0-6-2M 6MO-6-2M 6MO-6-3M 6MO-6-4M 8MO-6-6M 10MO-6-6M 10MO-6-8M 12MO-6-6M 12MO-6-8M 12MO-6-10M 16MO-6-10M 16MO-6-12M 18MO-6-12M 25MO-6-18M 25MO-6-20M

3 6 6 6 8 10 10 12 12 12 16 16 18 25 25

2 2 3 4 6 6 8 6 8 10 10 12 12 18 20

35,8 38,7 38,7 39,5 42,4 44,5 44,5 47,0 47,8 48,7 49,5 52,0 53,5 60,5 62,3

15,3 17,7 17,7 17,7 18,6 19,5 19,5 22,0 22,0 22,0 22,0 22,0 22,0 26,5 26,5

15,3 15,3 15,3 16,1 17,7 17,7 18,6 17,7 18,6 19,5 19,5 22,0 22,0 22,0 22,0

22,6 24,6 24,6 25,4 27,4 29,4 29,4 29,4 30,2 31,0 31,8 31,8 33,3 38,1 39,9

12,0 14,0 14,0 14,0 15,0 18,0 18,0 22,0 22,0 22,0 24,0 24,0 27,0 35,0 35,0

A C1 C2

T1 W HEX D

T2

NOTE: A, C1 and C2 dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

27
Parker Hannifin Corporation

Tube to Tube Unions
A

BC
Bulkhead Union
For fractional tube

C1

C2 W HEX

L1 D INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. W HEX

L2

A

C1

D

C2

L1

L2

BULKHEAD HOLE DRILL SIZE

MAXIMUM BULKHEAD THICKNESS

1BC1 2BC2 3BC3 4BC2 4BC4 5BC5 6BC6 8BC8 10BC10 12BC12 14BC14 16BC16

100-61 200-61 300-61 400-61-2 400-61 500-61 600-61 810-61 1010-61 1210-61 1410-61 1610-61

1/16 1/8 3/16 1/4 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1

1.23 2.02 2.11 2.17 2.27 2.40 2.46 2.80 2.86 3.11 3.33 3.78

.43 .60 .64 .70 .70 .73 .76 .87 .87 .87 .87 1.05

.94 1.50 1.59 1.03 1.69 1.81 1.88 2.00 2.06 2.31 2.53 2.81

.68 1.23 1.26 1.23 1.31 1.42 1.44 1.65 1.68 1.87 2.09 2.27

.28 .34 .38 .41 .41 .44 .47 .47 .47 .47 .47 .56

.53 .97 1.00 .97 1.02 1.12 1.15 1.25 1.28 1.47 1.69 1.78

5/16 1/2 9/16 5/8 5/8 11/16 3/4 15/16 1-1/16 1-3/16 1-3/8 1-5/8

13/64 21/64 25/64 21/64 29/64 33/64 37/64 49/64 57/64 1-1/64 1-9/64 1-21/64

1/8 1/2 1/2 1/2 17/32 9/16 9/16 19/32 19/32 25/32 15/16 15/16

NOTE: For reducer sizes call out short end first. A, C1 and C2 dimensions are typical finger-tight. For replacement bulkhead nuts, see Page 73, Part WLZ.

Dimensions for reference only, subject to change.

BCM
Bulkhead Union
For metric tube

A C1 C2 W HEX

L D MILLIMETERS INTERCHANGES WITH B’HEAD HOLE DRILL SIZE MAX. B’HEAD THICK.

PARKER PART NO.

TUBE O.D.

A

C1

C2

D

L

W HEX

BCM3 BCM4 BCM6 BCM8 BCM10 BCM12 BCM15 BCM16 BCM18 BCM20 BCM25

3MO-61 4MO-61 6MO-61 8MO-61 10MO-61 12MO-61 15MO-61 16MO-61 18MO-61 20MO-61 25MO-61

3 4 6 8 10 12 15 16 18 20 25

51,3 53,7 57,9 61,0 63,6 71,0 72,5 72,6 78,9 88,2 95,8

15,3 16,1 17,7 18,6 19,5 22,0 22,0 22,0 22,0 22,0 26,5

31,2 32,0 33,7 36,0 37,0 41,9 42,6 42,6 47,4 51,0 54,4

38,2 40,5 42,9 46,0 48,4 50,8 52,3 52,4 58,7 68,0 71,4

24,6 25,4 26,2 28,5 29,4 31,8 32,5 32,5 37,3 40,9 42,2

14,0 14,0 16,0 18,0 22,0 24,0 27,0 27,0 30,0 35,0 41,0

8,3 9,9 11,5 13,1 16,3 19,5 22,5 22,5 26,0 29,0 33,8

12,7 12,7 10,2 11,2 11,2 12,7 12,7 12,7 16,8 19,0 24,0

NOTE: A, C1 and C2 dimensions are typical finger-tight. For replacement bulkhead nuts, see Page 73, Part BN. For reducer sizes call out short end first.

Dimensions for reference only, subject to change.

28
Parker Hannifin Corporation

Tube to Tube Unions DELTA
Dielectric Union Adapter
For fractional tube
includes nuts, machined tube with molded ferrule, preset ferrule, and dielectric identification ring
PARKER ADAPTER PART NO. TUBE END T1 TUBE END T2 L T1 TURNED END TUBE O.D. E BORE L DIELECTRIC IDENTIFICATION RING T2 MACHINED END TUBE O.D. W1 HEX INCHES E BORE W1 HEX W2 HEX W2 HEX

6-8 DELTA 8-10 DELTA

3/8 1/2

1/2 5/8

2.08 2.58

.30 .38

11/16 7/8

7/8 1

NOTE: Makeup instructions included with parts in box when ordered as an Adapter only. *Other end connectors available upon request. Dimensions for reference only, subject to change.

DELTA
Dielectric Assembly
For fractional tube
includes dielectric union adapter with assembled tube fitting unions

PARKER ASSEMBLY PART NO. *COMPRESSION

INCHES A ADAPTER END CONNECTORS

4H DELTA 6H DELTA 8H DELTA
*COMPRESSION– FEMALE PIPE

4.08 4.20 4.79

6-8 DELTA 6-8 DELTA 8-10 DELTA

6RU4/8RU4 6SC6/8RU6 8SC8/10RU8

A

ADAPTER

END CONNECTORS

4G DELTA 6G DELTA 8G DELTA
A *COMPRESSION– MALE PIPE

3.59 3.71 4.40

6-8 DELTA 6-8 DELTA 8-10 DELTA

6FSC4N/8FSC4N 6FSC6N/8FSC6N 8FSC8N/10FSC8N

A

ADAPTER

END CONNECTORS

4F DELTA 6F DELTA 8F DELTA

3.80 3.80 4.58

6-8 DELTA 6-8 DELTA 8-10 DELTA

6MSC4N/8MSC4N 6MSC6N/8MSC6N 8MSC8N/10MSC8N

Finger tight assembly dimensions.

EE
Union Elbow
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. C L W HEX

1EE1 2EE2 3EE3 4EE4 5EE5 6EE6 8EE8 10EE10 12EE12 14EE14 16EE16 20EE20 24EE24 32EE32

100-9 200-9 300-9 400-9 500-9 600-9 810-9 1010-9 1210-9 1410-9 1610-9 2010-9 2410-9 3210-9

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2

.71 .88 1.00 1.06 1.17 1.20 1.42 1.43 1.56 1.76 1.94 2.61 3.06 4.22

.56 .62 .74 .77 .88 .91 1.02 1.03 1.16 1.36 1.45 1.75 2.00 2.75

3/8 3/8 1/2 1/2 5/8 5/8 13/16 7/8 1-1/16 1-3/8 1-3/8 1-5/8 1-7/8 2-13/16

C L

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

W HEX

29
Parker Hannifin Corporation

Tube to Tube Unions EEM
Union Elbow
For metric tube
PARKER PART NO. INTERCHANGES WITH MILLIMETERS TUBE O.D. C L INCH W HEX

EEM3 EEM4 EEM6 EEM8 EEM10 EEM12 EEM14 EEM15 EEM16 EEM18 EEM20 EEM22 EEM25

3MO-9 4MO-9 6MO-9 8MO-9 10MO-9 12MO-9 14MO-9 15MO-9 16MO-9 18MO-9 20MO-9 22MO-9 25MO-9

3 4 6 8 10 12 14 15 16 18 20 22 25

22,3 25,4 27,0 28.8 31,5 36,0 38,1 38,0 38,0 39,8 44,6 44,6 49,1

15,7 18,8 19,6 21,3 23,9 25,9 28,0 27,9 27,9 29,7 34,5 34,5 36,8

3/8 1/2 1/2 9/16 11/16 13/16 15/16 15/16 15/16 1-1/16 1-3/8 1-3/8 1-3/8

C L

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

W HEX

ELZ
Drop Size Elbows
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. L1 C1 L2 C2 W HEX

3-2 ELZ 4-2 ELZ 5-2 ELZ 5-4 ELZ 6-2 ELZ 6-4 ELZ 6-5 ELZ 8-4 ELZ 8-5 ELZ 8-6 ELZ 10-6 ELZ 10-8 ELZ 12-4 ELZ 12-6 ELZ 12-8 ELZ 14-4 ELZ 16-8 ELZ 16-12 ELZ

300-9-2 400-9-2 500-9-2 500-9-4 600-9-2 600-9-4 600-9-5 810-9-4 810-9-5 810-9-6 1010-9-6 1010-9-8 1210-9-4 1210-9-6 1210-9-8 1410-9-4 1610-9-8 1610-9-12

3/16-1/8 1/4-1/8 5/16-1/8 5/16-1/4 3/8-1/8 3/8-1/4 3/8-5/16 1/2-1/4 1/2-5/16 1/2-3/8 5/8-3/8 5/8-1/2 3/4-1/4 3/4-3/8 3/4-1/2 7/8-1/4 1-1/2 1-3/4

.69 .77 .88 .88 .91 .91 .91 1.02 1.02 1.02 1.03 1.03 1.16 1.16 1.16 1.36 1.45 1.45

.96 1.06 1.17 1.17 1.20 1.20 1.20 1.42 1.42 1.42 1.43 1.43 1.56 1.56 1.56 1.76 1.94 1.94

.66 .70 .78 .85 .78 .85 .88 .96 .99 1.02 1.03 1.03 1.09 1.16 1.16 1.22 1.22 1.36

.92 .96 1.04 1.14 1.04 1.09 1.17 1.25 1.28 1.31 1.32 1.43 1.38 1.45 1.56 1.51 1.62 1.76

7/16 1/2 5/8 5/8 5/8 5/8 5/8 13/16 13/16 13/16 7/8 7/8 1-1/16 1-1/16 1-1/16 1-3/8 1-5/16 1-3/8

C1 L1

NOTE: C dimension is typical finger-tight. W HEX L 2 C2

Dimensions for reference only, subject to change.

30
Parker Hannifin Corporation

Tube to Tube Unions ET
Union Tee
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. A C L W HEX

1ET1 2ET2 3ET3 4ET4 5ET5 6ET6 8ET8 10ET10 12ET12 14ET14 16ET16 20ET20 24ET24 32ET32

100-3 200-3 300-3 400-3 500-3 600-3 810-3 1010-3 1210-3 1410-3 1610-3 2010-3 2410-3 3210-3

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2

1.42 1.76 2.00 2.12 2.34 2.40 2.84 2.86 3.12 3.52 3.88 5.22 6.12 8.44

.71 .88 1.00 1.06 1.17 1.20 1.42 1.43 1.56 1.76 1.94 2.61 3.06 4.22

.56 .62 .74 .77 .88 .91 1.02 1.03 1.16 1.36 1.45 1.75 2.00 2.75

3/8 3/8 1/2 1/2 5/8 5/8 13/16 7/8 1-1/16 1-3/8 1-3/8 1-5/8 1-7/8 2-13/16

A C L

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

W HEX

ETM
Union Tee
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. A C L

INCH W HEX

ETM2 ETM3 ETM4 ETM6 ETM8 ETM10 ETM12 ETM14 ETM15 ETM16 ETM18 ETM20 ETM22 ETM25

2MO-3 3MO-3 4MO-3 6MO-3 8MO-3 10MO-3 12MO-3 14MO-3 15MO-3 16MO-3 18MO-3 20MO-3 22MO-3 25MO-3

2 3 4 6 8 10 12 14 15 16 18 20 22 25

44,7 44,7 50,8 53,9 59,7 63,0 72,0 77,6 77,6 77,6 79,5 89,3 89,3 98,3

22,3 22,3 25,4 27,0 29,9 31,5 36,0 38,8 38,8 38,8 38,8 44,6 44,6 49,1

15,7 15,7 18,8 19,6 22,4 23,9 25,9 28,7 28,7 28,7 29,7 34,5 34,5 36,8

3/8 3/8 1/2 1/2 5/8 11/16 13/16 1 1 1 1-1/16 1-3/8 1-3/8 1-3/8

A C L

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

W HEX

31
Parker Hannifin Corporation

Tube to Tube Unions
A

JLZ
Drop Size Tees
For fractional tube
Eliminates the extra connection when adapting with a tube stub reducer
T1

C1 L1 L2

C2

W HEX

T2

L3

C3

T3 INCHES PARKER PART NO. INTERCHANGES WITH T1 TUBE O.D. T2 TUBE O.D. T3 TUBE O.D. A L1 C1 L2 C2 L3 C3 W HEX

4-4-2 JLZ 6-6-4 JLZ 6-4-6 JLZ 6-4-4 JLZ 8-8-6 JLZ 8-8-4 JLZ 8-6-8 JLZ 8-4-8 JLZ 8-6-6 JLZ 8-4-4 JLZ 10-10-8 JLZ 10-10-6 JLZ 10-8-8 JLZ 10-8-6 JLZ 10-6-6 JLZ 10-6-8 JLZ 12-12-10 JLZ 12-12-8 JLZ 12-12-6 JLZ 12-12-4 JLZ 12-10-10 JLZ 12-8-8 JLZ 12-6-6 JLZ 12-10-8 JLZ 12-10-6 JLZ 12-8-6 JLZ 14-14-6 JLZ 14-14-4 JLZ 14-12-12 JLZ 14-12-8 JLZ 14-12-6 JLZ 14-10-6 JLZ 14-8-12 JLZ 16-16-12 JLZ 16-16-10 JLZ 16-16-8 JLZ 16-16-6 JLZ 16-16-4 JLZ 16-12-16 JLZ 16-14-14 JLZ 16-14-12 JLZ 16-14-8 JLZ 16-14-6 JLZ 16-14-4 JLZ 16-16-14 JLZ 16-12-10 JLZ 16-12-8 JLZ 16-10-6 JLZ 16-8-16 JLZ 16-8-8 JLZ 16-8-6 JLZ 16-8-4 JLZ 16-6-6 JLZ

400-3-4-2 600-3-6-4 600-3-4-6 600-3-4-4 810-3-8-6 810-3-8-4 810-3-6-8 810-3-4-8 810-3-6-6 810-3-4-4 1010-3-10-8 1010-3-10-6 1010-3-8-8 1010-3-8-6 1010-3-6-6 1010-3-6-8 1210-3-12-10 1210-3-12-8 1210-3-12-6 1210-3-12-4 1210-3-10-10 1210-3-8-8 1210-3-6-6 1210-3-10-8 1210-3-10-6 1210-3-8-6 1410-3-14-6 1410-3-14-4 1410-3-12-12 1410-3-12-8 1410-3-12-6 1410-3-10-6 1410-3-8-12 1610-3-16-12 1610-3-16-10 1610-3-16-8 1610-3-16-6 1610-3-16-4 1610-3-12-16 1610-3-14-14 1610-3-14-12 1610-3-14-8 1610-3-14-6 1610-3-14-4 1610-3-16-14 1610-3-12-10 1610-3-12-8 1610-3-10-6 1610-3-8-16 1610-3-8-8 1610-3-8-6 1610-3-8-4 1610-3-6-6

1/4 3/8 3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 7/8 7/8 7/8 7/8 7/8 7/8 7/8 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1/4 3/8 1/4 1/4 1/2 1/2 3/8 1/4 3/8 1/4 5/8 5/8 1/2 1/2 3/8 3/8 3/4 3/4 3/4 3/4 5/8 1/2 3/8 5/8 5/8 1/2 7/8 7/8 3/4 3/4 3/4 5/8 1/2 1 1 1 1 1 3/4 7/8 7/8 7/8 7/8 7/8 1 3/4 3/4 5/8 1/2 1/2 1/2 1/2 3/8

1/8 1/4 3/8 1/4 3/8 1/4 1/2 1/2 3/8 1/4 1/2 3/8 1/2 3/8 3/8 1/2 5/8 1/2 3/8 1/4 5/8 1/2 3/8 1/2 3/8 3/8 3/8 1/4 3/4 1/2 3/8 3/8 3/4 3/4 5/8 1/2 3/8 1/4 1 7/8 3/4 1/2 3/8 1/4 7/8 5/8 1/2 3/8 1 1/2 3/8 1/4 3/8

2.10 2.40 2.34 2.34 2.84 2.84 2.73 2.67 2.73 2.67 2.86 2.86 2.86 2.86 2.75 2.75 3.12 3.12 3.12 3.12 3.12 3.12 3.01 3.12 3.12 3.12 3.52 3.52 3.52 3.52 3.52 3.52 3.52 3.88 3.88 3.88 3.88 3.88 3.70 3.70 3.70 3.70 3.70 3.70 3.70 3.70 3.70 3.70 3.70 3.70 3.70 3.70 3.59

.76 .91 .91 .91 1.02 1.02 1.02 1.02 1.02 1.02 103 1.03 1.03 1.03 1.03 1.03 1.16 1.16 1.16 1.16 1.16 1.16 1.16 1.16 1.16 1.16 1.36 1.36 1.36 1.36 1.36 1.36 1.36 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45

1.05 1.20 1.20 1.20 1.42 1.42 1.42 1.42 1.42 1.42 1.43 1.43 1.43 1.43 1.43 1.43 1.56 1.56 1.56 1.56 1.56 1.56 1.56 1.56 1.56 1.56 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94 1.94

.76 .91 .85 .85 1.02 1.02 1.02 .96 1.02 .96 1.03 1.03 1.03 1.03 1.03 1.03 1.16 1.16 1.16 1.16 1.16 1.16 1.16 1.16 1.16 1.16 1.36 1.36 1.36 1.36 1.36 1.36 1.36 1.45 1.45 1.45 1.45 1.45 1.36 1.36 1.36 1.36 1.36 1.36 1.45 1.36 1.36 1.36 1.36 1.36 1.36 1.36 1.36

1.05 1.20 1.14 1.14 1.42 1.42 1.31 1.25 1.31 1.25 1.43 1.43 1.43 1.43 1.32 1.32 1.56 1.56 1.56 1.56 1.56 1.56 1.45 1.56 1.56 1.56 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.94 1.94 1.94 1.94 1.94 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.76 1.65

.70 .85 .91 .85 1.02 .96 1.02 1.02 1.02 .96 1.03 1.03 1.03 1.03 1.03 1.03 1.16 1.16 1.16 1.09 1.16 1.16 1.16 1.16 1.16 1.16 1.36 1.30 1.36 1.36 1.36 1.36 1.36 1.36 1.36 1.36 1.36 1.30 1.45 1.36 1.36 1.36 1.36 1.30 1.36 1.36 1.36 1.36 1.45 1.36 1.36 1.30 1.36

.96 1.14 1.20 1.14 1.31 1.25 1.42 1.42 1.31 1.25 1.43 1.32 1.43 1.32 1.32 1.43 1.56 1.56 1.45 1.38 1.56 1.56 1.45 1.56 1.45 1.45 1.65 1.59 1.76 1.76 1.65 1.65 1.76 1.76 1.76 1.76 1.65 1.59 1.94 1.76 1.76 1.76 1.65 1.59 1.76 1.76 1.76 1.65 1.94 1.76 1.65 1.59 1.65

1/2 5/8 5/8 5/8 13/16 13/16 13/16 13/16 13/16 13/16 7/8 7/8 7/8 7/8 7/8 7/8 1-1/16 1-1/16 1-1/16 1-1/16 1-1/16 1-1/16 1-1/16 1-1/16 1-1/16 1-1/16 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16 1-5/16

NOTE: C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

32
Parker Hannifin Corporation

Tube to Tube Unions ECR
Union Cross
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. A C L W HEX

2ECR2 3ECR3 4ECR4 5ECR5 6ECR6 8ECR8 10ECR10 12ECR12 14ECR14 16ECR16

200-4 300-4 400-4 500-4 600-4 810-4 1010-4 1210-4 1410-4 1610-4

1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1

1.84 1.92 2.02 2.28 2.26 2.74 2.86 3.12 3.52 3.86

.92 .95 1.01 1.14 1.13 1.37 1.43 1.56 1.76 1.93

.66 .69 .72 .84 .84 .97 1.03 1.16 1.36 1.45

7/16 7/16 7/16 9/16 9/16 3/4 1-1/16 1-1/16 1-5/16 1-5/16

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

A C L

W HEX

ECRM
Union Cross
For metric tube
A C L PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. A C L

INCH W HEX

ECRM3 ECRM4 ECRM6 ECRM8 ECRM10 ECRM12 ECRM16 ECRM18

3MO-4 4MO-4 6MO-4 8MO-4 10MO-4 12MO-4 16MO-4 18MO-4

3 4 6 8 10 12 16 18

44,7 50,8 53,9 59,7 67,0 72,0 74,0 76,6

22,3 25,4 27,0 29,9 33,5 36,0 37,0 38,3

15,7 18,8 19,6 22,4 25,9 25,9 26,9 28,2

7/16 1/2 1/2 5/8 13/16 13/16 15/16 1-1/16

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

W HEX

33
Parker Hannifin Corporation

Port Connectors TUR
Tube End Reducer
For fractional tube
T1 TURNED END TUBE O.D. W HEX D A K C

BORE

T2 MACHINED END TUBE O.D.

INCHES PARKER PART NO. INTERCHANGES WITH T1 TURNED END TUBE O.D. T2 MACHINE END TUBE O.D. W HEX

A

C

D

K

BORE

2TUR1* 3TUR1* 4TUR1 1TUR2* 2TUR2* 3TUR2* 4TUR2 6TUR2 8TUR2 2TUR3* 4TUR3 2TUR4* 3TUR4* 4TUR4 5TUR4 6TUR4 8TUR4 10TUR4 12TUR4 6TUR5 8TUR5 4TUR6 6TUR6 8TUR6 10TUR6 12TUR6 4TUR8 6TUR8 10TUR8 12TUR8 16TUR8 12TUR10 14TUR10 16TUR10 8TUR12 16TUR12 24TUR16 24TUR20 32TUR24

100-R-2 100-R-3 100-R-4 200-R-1 200-R-2 200-R-3 200-R-4 200-R-6 200-R-8 300-R-2 300-R-4 400-R-2 400-R-3 400-R-4 400-R-5 400-R-6 400-R-8 400-R-10 400-R-12 500-R-6 500-R-8 600-R-4 600-R-6 600-R-8 600-R-10 600-R-12 810-R-4 810-R-6 810-R-10 810-R-12 810-R-16 1010-R-12 1010-R-14 1010-R-16 1210-R-8 1210-R-16 1610-R-24 2010-R-24 2410-R-32

1/8 3/16 1/4 1/16 1/8 3/16 1/4 3/8 1/2 1/8 1/4 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 3/8 1/2 1/4 3/8 1/2 5/8 3/4 1/4 3/8 5/8 3/4 1 3/4 7/8 1 1/2 1 1-1/2 1-1/2 2

1/16 1/16 1/16 1/8 1/8 1/8 1/8 1/8 1/8 3/16 3/16 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 3/4 3/4 1 1-1/4 1-1/2

1.10 1.13 1.24 1.18 1.34 1.35 1.42 1.48 1.74 1.37 1.46 1.45 1.48 1.54 1.57 1.60 1.82 1.89 1.88 1.65 1.87 1.63 1.70 1.91 1.98 1.98 1.77 1.84 2.12 2.12 2.37 2.15 2.21 2.40 2.15 2.46 3.519 4.10 5.17

.43 .43 .43 .60 .43 .60 .60 .60 .60 .63 .63 .70 .60 .70 .70 .70 .70 .70 .70 .73 .73 .76 .76 .76 .76 .76 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 1.05 1.52 1.52

.95 .98 1.09 .922 1.09 1.09 1.16 1.22 1.48 1.11 1.20 1.16 1.19 1.25 1.28 1.31 1.53 1.60 1.59 1.36 1.58 1.34 1.41 1.62 1.69 1.69 1.37 1.44 1.72 1.72 1.97 1.75 1.81 2.00 1.75 2.06 3.03 3.23 4.10

.53 .58 .63 .38 .54 .58 .63 .69 .91 .53 .63 .53 .56 .63 .66 .69 .91 .97 .97 .69 .91 .63 .69 .91 .97 .97 .63 .69 .97 .97 1.22 .97 1.03 1.22 .91 1.22 2.05 2.05 2.74

5/16 5/16 7/16 7/16 7/16 7/16 7/16 7/16 9/16 7/16 7/16 1/2 1/2 1/2 1/2 1/2 9/16 11/16 13/16 9/16 9/16 5/8 5/8 5/8 11/16 13/16 13/16 13/16 13/16 13/16 1-1/16 15/16 15/16 1-1/16 1-1/16 1-1/16 1-5/8 1-7/8 2-1/4

.05 .05 .05 .09 .07 .09 .09 .09 .09 .08 .13 .08 .12 .19 .19 .19 .19 .19 .19 .25 .25 .19 .28 .28 .28 .28 .19 .19 .41 .41 .41 .50 .50 .50 .39 .63 .88 1.09 1.34

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. Size 4 and above tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. *Size 1, 2, and 3 do not require a groove. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

34
Parker Hannifin Corporation

Port Connectors TUCM
Tube End Converter
For metric tube
T1 TURNED END TUBE O.D. W HEX D A K C

T2 MACHINED END TUBE O.D.

PARKER PART NO.

INTERCHANGES WITH

TUBE O.D. T1 INCH T2 MM A C D

MILLIMETERS K W A/F HEX BORE

2TUCM3 4TUCM3 4TUCM6 5TUCM6 6TUCM6 8TUCM6 6TUCM8 8TUCM8 6TUCM10 8TUCM10 8TUCM12 12TUCM12 12TUCM18

3MO-R-2 3MO-R-4 6MO-R-4 6MO-R-5 6MO-R-6 6MO-R-8 8MO-R-6 8MO-R-8 10MO-R-6 10MO-R-8 12MO-R-8 12MO-R-12 18MO-R-12

1/8 1/4 1/4 5/16 3/8 1/2 3/8 1/2 3/8 1/2 1/2 3/4 3/4

3 3 6 6 6 6 8 8 10 10 12 12 18

34,3 36,1 39,3 40,0 40,8 46,4 42,0 47,5 44,4 47,6 52,3 53,8 57,5

15,3 15,3 17,7 17,7 17,7 17,7 18,6 18,6 19,5 19,5 22,0 22,0 22,0

27,7 29,5 31,8 32,5 33,3 38,9 34,5 40,1 36,8 41,4 42,2 43,7 47,5

13,5 16,0 16,0 16,8 17,5 23,1 17,5 23,1 17,5 23,1 23,1 24,6 24,6

12,0 12,0 14,0 14,0 14,0 14,0 15,0 15,0 18,0 18,0 22,0 22,0 27,0

1,4 4,8 4,8 6,4 7,1 9,9 7,1 9,9 7,1 9,9 9,9 15,1 15,1

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Size 1, 2, and 3 do not require a groove. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

35
Parker Hannifin Corporation

Port Connectors TURM
Tube End Reducer
For metric tube
PARKER PART NO. MILLIMETERS INTERCHANGES WITH TUBE O.D. T1 T2 A C D K Q W HEX

BORE

M3TURM2 M3TURM6 M4TURM3 M6TURM3 M6TURM4 M6TURM8 M6TURM10 M6TURM12 M8TURM6 M8TURM10
T2 MACHINED END TUBE O.D.

2MO-R-3M 6MO-R-3M 3MO-R-4M 3MO-R-6M 4MO-R-6M 8MO-R-6M 10MO-R-6M 12MO-R-6M 6MO-R-8M 10MO-R-8M 3MO-R-10M 6MO-R-10M 8MO-R-10M 12MO-R-10M 6MO-R-12M 8MO-R-12M 10MO-R-12M 16MO-R-12M 18MO-R-12M 10MO-R-15M 12MO-R-16M 18MO-R-16M 20MO-R-16M 25MO-R-16M 12MO-R-18M 16MO-R-18M 20MO-R-18M 25MO-R-18M 12MO-R-20M 16MO-R-20M 18MO-R-20M 25MO-R-20M 18MO-R-22M 20MO-R-22M 12MO-R-25M 16MO-R-25M 18MO-R-25M 20MO-R-25M

3 3 4 6 6 6 6 6 8 8 10 10 10 10 12 12 12 12 12 15 16 16 16 16 18 18 18 18 20 20 20 20 22 22 25 25 25 25

2 6 3 3 4 8 10 12 6 10 3 6 8 12 6 8 10 16 18 10 12 18 20 25 12 16 20 25 12 16 18 25 18 20 12 16 18 20

34,3 37,0 35,0 36,1 37,1 40,0 41,7 44,9 40,0 43,4 38,6 40,8 42,0 46,6 46,4 47,6 49,7 53,0 54,6 51,3 53,8 56,1 57,9 63,2 53,8 54,7 57,9 63,1 56,1 55,3 57,6 64,5 56,1 57,7 60,9 64,0 62,5 64,2

15,3 17,7 15,3 15,3 16,1 18,6 19,5 22,0 17,7 19,5 15,3 17,7 18,6 22,0 17,7 18,6 19,5 22,0 22,0 19,5 22,0 22,0 22,0 26,5 22,0 22,0 22,0 26,5 22,0 22,0 22,0 26,5 22,0 22,0 22,0 22,0 22,0 22,0

27,7 29,5 28,4 29,5 30,5 32,5 34,1 34,8 32,5 35,8 32,0 33,3 34,5 36,5 38,9 40,1 42,1 42,9 44,5 43,7 43,7 46,0 47,8 51,0 43,7 44,6 47,8 50,8 46,0 45,2 47,5 52,3 46,0 47,6 50,8 51,8 52,4 54,1

13,5 13,5 14,3 15,9 15,9 15,9 15,9 15,9 16,7 15,3 17,7 17,5 17,5 17,5 23,0 23,0 23,0 23,0 23,0 23,8 24,6 24,6 24,6 24,8 24,6 24,8 24,6 24,6 25,4 25,6 25,4 25,4 26,2 26,2 31,8 32,0 31,8 31,8

0,6 0,6 1,0 1,0 1,0 1,0 1,0 1,0 0,8 1,5 2,0 1,3 1,3 1,3 1,4 1,4 1,4 1,4 1,4 1,6 1,7 1,7 1,7 2,0 2,0 2,5 2,0 2,0 2,5 2,5 2,5 2,5 2,5 2,5 2,6 3,0 2,6 2,6

14,0 14,0 12,0 12,0 12,0 15,0 18,0 22,0 14,0 19,5 15,3 14,0 15,0 22,0 14,0 15,0 18,0 24,0 27,0 27,0 22,0 27,0 27,0 26,5 22,0 22,0 30,0 35,0 22,0 22,0 27,0 35,0 27,0 30,0 27,0 22,0 27,0 30,0

1,4 1,4 2,0 2,4 3,0 4,0 4,0 4,0 4,8 18,0 12,0 4,8 6,4 7,5 4,8 6,4 7,9 9,1 9,1 7,9 9,5 12,7 12,7 35,0 9,5 24,0 13,9 14,0 9,5 24,0 15,1 15,1 15,1 15,8 9,5 27,0 15,1 15,8

A K C

T1 TURNED END TUBE O.D. W HEX D

BORE

M10TURM3 M10TURM6 M10TURM8 M10TURM12 M12TURM6 M12TURM8 M12TURM10 M12TURM16 M12TURM18 M15TURM10 M16TURM12 M16TURM18 M16TURM20 M16TURM25 M18TURM12 M18TURM16 M18TURM20 M18TURM25 M20TURM12 M20TURM16 M20TURM18 M20TURM25 M22TURM18 M22TURM20 M25TURM12 M25TURM16 M25TURM18 M25TURM20

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. Tube stub is pre-grooved as standard. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

A

TUBC
Tube End Bulkhead Adapter
For fractional tube

C K L

BORE

W HEX D INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. W HEX

A

C

L

K

D

BORE

2TUBC2 4TUBC4 6TUBC6 8TUBC8

200-R1-2 400-R1-4 600-R1-6 810-R1-8

1/8 1/4 3/8 1/2

1.95 2.20 2.42 2.87

1.23 1.31 1.44 1.65

.97 1.02 1.15 1.25

.53 .63 .69 .91

1.69 1.91 2.13 2.47

.093 .187 .281 .406

1/2 5/8 3/4 15/16

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

36
Parker Hannifin Corporation

Port Connectors PC
Port Connector
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. A K BORE

1PC1 1PC2 1PC4 2PC2 2PC4 2PC6 3PC3 4PC4 4PC6 4PC8 6PC6 6PC8 8PC8 8PC12 12PC12 16PC16

101-PC 201-PC-1 401-PC-1 201-PC 401-PC-2 601-PC-2 301-PC 401-PC 601-PC-4 811-PC-4 601-PC 811-PC-6 811-PC 1211-PC-8 1211-PC 1611-PC

1/16 1/16-1/8 1/16-1/4 1/8 1/8-1/4 1/8-3/8 3/16 1/4 1/4-3/8 1/4-1/2 3/8 3/8-1/2 1/2 1/2-3/4 3/4 1

.63 .84 .91 .95 1.05 1.09 .981 1.07 1.15 1.36 1.16 1.40 1.59 1.72 1.65 2.12

.44 .44 .44 .54 .54 .54 .67 .76 .64 .64 .84 .72 1.11 .91 1.16 1.44

.031 .031 .031 .078 .078 .031 .116 .156 .156 .156 .281 .281 .375 .375 .578 .813

A K BORE

Dimensions for reference only, subject to change. NOTE: Tube stub is pre-grooved as standard. (Size 1, 2, and 3 not grooved). Generic (non-grooved 4-16) can be ordered through Quick Response Department. The machined ferrule end (T2) requires only 1/4 turn from finger tight to assemble. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

PCM
Port Connector
For metric tube
PARKER PART NO. INTERCHANGES WITH TUBE O.D. T1 T2

MILLIMETERS

A

K

BORE

A K T1 TURNED END TUBE O.D. T2 MACHINED END TUBE O.D.

PCM 3 PCM 6 PCM 8 PCM 10 PCM 12 PCM 16 PCM 18 M3PCM6 M6PCM8 M6PCM10 M6PCM12 M8PCM10 M8PCM12

3M1-PC 6M1-PC 8M1-PC 10M1-PC 12M1-PC 16M1-PC 18M1-PC 6M1-PC-3M 8M1-PC-6M 10M1-PC-6M 12M1-PC-6M 10M1-PC-8M 12M1-PC-8M

3 6 8 10 12 16 18 3 6 6 6 8 8

3 6 8 10 12 16 18 6 8 10 12 10 12

22,2 24,6 25,9 26,1 35,8 40,5 40,8 22,6 25,5 25,5 31,2 29,5 31,4

15,7 18,7 20,0 20,2 26,0 27,7 27,7 13,5 16,1 16,1 16,1 16,8 16,8

1,6 3,0 5,0 6,0 8,0 12,0 13,0 1,6 3,0 3,0 3,0 5,0 5,0

Dimensions for reference only, subject to change. NOTE: Tube stub is pre-grooved as standard. (Size M2, M3, and M4 not grooved). The machined ferrule end (T2) requires only 1/4 turn from finger tight to assemble. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

37
Parker Hannifin Corporation

Port Connectors
A

MAN
NPT Tube End Male Adapter
For fractional tube
INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. NPT PIPE THREAD

K

R

BORE

W HEX

A

R

K

W HEX

BORE

1MA2N 2MA2N 2MA4N 3MA2N 3MA4N 4MA2N 4MA4N 4MA6N 4MA8N 5MA2N 5MA4N 5MA6N 5MA8N 6MA2N 6MA4N 6MA6N 6MA8N 8MA4N 8MA6N 8MA8N 10MA8N 12MA8N 12MA12N 12MA16N 16MA12N 16MA16N 20MA20N 24MA24N 32MA32N

1-TA-1-1 2-TA-1-2 2-TA-1-4 3-TA-1-2 3-TA-1-4 4-TA-1-2 4-TA-1-4 4-TA-1-6 4-TA-1-8 5-TA-1-2 5-TA-1-4 5-TA-1-6 5-TA-1-8 6-TA-1-2 6-TA-1-4 6-TA-1-6 6-TA-1-8 8-TA-1-4 8-TA-1-6 8-TA-1-8 10-TA-1-8 12-TA-1-8 12-TA-1-12 12-TA-1-16 16-TA-1-12 16-TA-1-16 20-TA-1-20 24-TA-1-24 32-TA-1-32

1/16 1/8 1/8 3/16 3/16 1/4 1/4 1/4 1/4 5/16 5/16 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 3/4 3/4 3/4 1 1 1-1/4 1-1/2 2

1/8 1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/2 1/4 3/8 1/2 1/2 1/2 3/4 1 3/4 1 1-1/4 1-1/2 2

1.00 1.16 1.38 1.20 1.42 1.25 1.46 1.49 1.71 1.29 1.50 1.53 1.74 1.32 1.53 1.56 1.78 1.75 1.78 2.00 2.06 2.06 2.06 2.41 2.31 2.68 3.16 3.72 4.70

.38 .38 .56 .38 .56 .38 .56 .56 .75 .38 .56 .56 .75 .38 .56 .56 .75 .56 .56 .75 .75 .75 .75 .94 .75 .94 .97 1.00 1.04

.38 .54 .54 .58 .58 .63 .63 .63 .63 .66 .66 .66 .66 .69 .69 .69 .69 .91 .91 .91 .97 .97 .97 .97 1.22 1.22 1.71 2.05 2.74

7/16 7/16 9/16 7/16 9/16 7/16 9/16 11/16 7/8 7/16 9/16 11/16 7/8 7/16 9/16 11/16 7/8 9/16 11/16 7/8 7/8 7/8 1-1/16 1-3/8 1-1/16 1-3/8 1-3/4 2-1/8 2-3/4

.031 .078 .078 .116 .116 .156 .156 .156 .156 .219 .219 .219 .219 .281 .281 .281 .281 .281 .375 .375 .469 .469 .578 .813 .813 .813 1.00 1.25 1.72

NOTE: Add -Z6 for assembly of nuts and ferrules on the tube stub end. Dimensions for reference only, subject to change. Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Inch sizes 1, 2, and 3 and metric sizes 2, 3, and 4mm do not have grooves.

MAR
BSPP Tube End Male Adapter
For fractional tube
BSPP

A K R

BSPP

W HEX INTERCHANGES WITH INCHES TUBE O.D. BSPP THREAD A K R HEX W BORE

PARKER PART NO.

2MA2R 2MA4R 4MA2R 4MA4R 6MA2R 6MA4R 6MA6R 6MA8R 8MA4R 8MA6R 8MA8R 10MA8R 12MA12R 16MA16R

2TA-1-2RS 2TA-1-4RS 4TA-1-2RS 4TA-1-4RS 6TA-1-2RS 6TA-1-4RS 6TA-1-6RS 6TA-1-8RS 8TA-1-4RS 8TA-1-6RS 8TA-1-8RS 10TA-1-8RS 12TA-1-12RS 16TA-1-16RS

1/8 1/8 1/4 1/4 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 3/4 1

1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/4 3/8 1/2 1/2 3/4 1

1.09 1.31 1.19 1.50 1.34 1.47 1.50 1.69 1.69 1.72 1.94 1.97 2.09 2.53

.53 .53 .63 .63 .69 .69 .69 .69 .91 .91 .91 .97 .97 1.22

.28 .44 .28 .44 .28 .44 .44 .56 .44 .44 .56 .56 .63 .72

9/16 3/4 9/16 3/4 3/4 3/4 7/8 1-1/16 3/4 7/8 1-1/16 1-1/16 1-5/16 1-5/8

.05 .05 .16 .18 .05 .25 .28 .28 .25 .31 .39 .47 .578 .80

NOTE: Add -Z6 for assembly of nuts and ferrules on the tube stub end. Dimensions for reference only, subject to change. Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Bonded sealing washer must be used with this design.

38
Parker Hannifin Corporation

Port Connectors MAR
BSPP Tube End Male Adapter
For metric tube
K
BSPP

A R

BSPP

W HEX INTERCHANGES WITH MILLIMETERS TUBE O.D. BSPP THREAD A K Q R X W HEX BORE

PARKER PART NO.

M3MA1/8R M4MA1/8R M6MA1/8R M6MA1/4R M8MA1/4R M10MA1/4R M10MA3/8R M10MA1/2R M12MA1/4R M12MA3/8R M12MA1/2R M16MA1/2R M18MA3/4R M20MA3/4R M25MA1R

3-MTA-1-2RS 4-MTA-1-2RS 6-MTA-1-2RS 6-MTA-1-4RS 8-MTA-1-4RS 10-MTA-1-4RS 10-MTA-1-6RS 10-MTA-1-8RS 12-MTA-1-4RS 12-MTA-1-6RS 12-MTA-1-8RS 16-MTA-1-8RS 18-MTA-1-12RS 20-MTA-1-12RS 25-MTA-1-16RS

3 4 6 6 8 10 10 10 12 12 12 16 18 20 25

1/8 1/8 1/8 1/4 1/4 1/4 3/8 1/2 1/4 3/8 1/2 1/2 3/4 3/4 1

31,0 31,8 33,3 38,1 38,9 39,7 38,9 42,9 43,7 44,5 49,2 50,8 53,2 54,0 65,1

13,5 14,3 15,9 15,9 16,7 17,5 17,5 17,5 23,0 23,0 23,0 24,6 24,6 25,4 31,8

0,6 1,0 1,0 1,0 0,8 1,3 1,3 1,3 1,4 1,4 1,4 1,7 2,0 2,5 2,6

7,1 7,1 7,1 11,2 11,2 11,2 11,2 14,2 11,2 11,2 14,2 14,2 16,0 16,0 18,3

13,7 13,7 13,7 17,8 17,8 17,8 21,8 25,7 17,8 21,8 25,7 25,7 31,8 31,8 38,6

14,0 14,0 14,0 19,0 19,0 19,0 22,0 27,0 19,0 22,0 27,0 27,0 33,0 33,0 41,0

1,8 2,0 4,0 4,0 6,4 6,4 7,5 7,5 6,4 7,9 9,1 11,9 14,0 15,1 19,8

NOTE: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Bonded sealing washer must be used with this design. Dimensions for reference only, subject to change. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

MAR
BSPP Tube End Male Adapter with ED Seal
For fractional tube
K
BSPP

A R
BSPP

W HEX INTERCHANGES WITH INCHES TUBE O.D. BSPP THREAD A K R X W HEX BORE

PARKER PART NO.

4MA4R-ED 4MA6R-ED 8MA4R-ED 8MA6R-ED 8MA8R-ED

– – – – –

1/4 1/4 1/2 1/2 1/2

1/4 3/8 1/4 3/8 1/2

1.50 1.50 1.75 1.78 1.94

.63 .63 .91 .91 .91

.47 .47 .47 .47 .55

.74 .86 .74 .86 1.04

3/4 3/4 3/4 7/8 1.1/16

.18 .18 .25 .31 .39

NOTE: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. ED fitttings are supplied with sealing washers in Buna-N as standard, suitable for temperatures between –35°C and +100°C (–31°F to +212°F). Viton seals are available upon request which are suitable for temperatures between –25°C and +120°C (13°F to +248°F). Dimensions for reference only, subject to change. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

39
Parker Hannifin Corporation

Port Connectors MAR
BSPP Tube End Male Adapter with ED Seal
For metric tube
BSPP

A K R

BSPP

W HEX MILLIMETERS TUBE O.D. BSPP THREAD A K R W HEX BORE

PARKER PART NO.

INTERCHANGES WITH

M6MA1/4R-ED M6MA1/2R-ED M10MA1/4R-ED M10MA1/2R-ED M12MA1/4R-ED M12MA3/8R-ED M12MA1/2R-ED

– – – – – – –

6 6 10 10 12 12 12

1/4 1/2 1/4 1/2 1/4 3/8 1/2

36,6 42,7 38,1 44,2 43,7 45,0 49,8

15,9 15,9 17,5 17,5 23,0 23,0 23,0

7,9 14,0 11,9 14,0 11,9 11,9 14,0

19,0 27,0 19,0 27,0 19,0 22,0 27,0

4,0 4,0 6,4 7,5 6,4 7,9 9,1

NOTE: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. ED fittings are supplied with sealing washers in Buna-N as standard, suitable for temperatures between –35°C and +100°C (–31°F to +212°F). Viton seals are available upon request which are suitable for temperatures between –25°C and +120°C (13°F to +248°F). Dimensions for reference only, subject to change. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

MAN
NPT Male Adapter
For metric tube

A K R

W HEX INTERCHANGES WITH MILLIMETERS TUBE O.D. NPT THREAD A K R W HEX BORE

PARKER PART NO.

M3MA1/8N M4MA1/8N M6MA1/8N M6MA1/4N M6MA3/8N M6MA1/2N M8MA1/4N M8MA3/8N M10MA1/4N M10MA3/8N M10MA1/2N M12MA1/4N M12MA3/8N M12MA1/2N M16MA1/2N M16MA3/4N M18MA1/2N M18MA3/4N M20MA1/2N M20MA3/4N M25MA1N

3-MTA-1-2 4-MTA-1-2 6-MTA-1-2 6-MTA-1-4 6-MTA-1-6 6-MTA-1-8 8-MTA-1-4 8-MTA-1-6 10-MTA-1-4 10-MTA-1-6 10-MTA-1-8 12-MTA-1-4 12-MTA-1-6 12-MTA-1-8 16-MTA-1-8 16-MTA-1-12 18-MTA-1-8 18-MTA-1-12 20-MTA-1-8 20-MTA-1-12 25-MTA-1-16

3 4 6 6 6 6 8 8 10 10 10 12 12 12 16 16 18 18 20 20 25

1/8 1/8 1/8 1/4 3/8 1/2 1/4 3/8 1/4 3/8 1/2 1/4 3/8 1/2 1/2 3/4 1/2 3/4 1/2 3/4 1

29,4 29,4 31,0 35,7 36,5 42,1 37,3 38,1 38,1 43,7 44,5 43,7 44,5 49,2 50,8 51,6 50,8 51,6 51,8 52,4 65,9

13,5 14,3 15,9 15,9 16,1 16,1 16,7 16,7 17,5 17,5 17,5 23,0 23,0 23,0 24,6 24,6 24,6 24,6 25,6 25,4 31,8

9,7 9,7 9,7 14,2 14,2 19,1 14,2 14,2 14,2 14,2 19,1 14,2 14,2 19,1 19,1 19,1 19,1 19,1 19,1 19,1 23,9

12,0 12,0 12,0 14,0 18,0 22,0 14,0 12,0 14,0 18,0 22,0 14,0 27,0 22,0 22,0 27,0 22,0 27,0 22,0 27,0 35,0

1,8 2,0 4,0 4,0 3,0 3,0 6,4 6,4 7,1 7,5 7,5 7,1 9,1 9,1 12,7 12,7 12,7 14,0 15,0 15,1 19,8

NOTE: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

Dimensions for reference only, subject to change.

40
Parker Hannifin Corporation

Port Connectors MAK
BSP Taper Male Adapter
For fractional tube
BSP

A K R

BSP

W HEX INTERCHANGES WITH INCHES TUBE O.D. BSP TR THREAD A K R W HEX BORE

PARKER PART NO.

4MA2K 4MA4K 4MA6K 4MA8K 5MA2K 5MA4K 6MA4K 6MA6K 6MA8K 8MA4K 8MA6K 8MA8K 10MA8K

4-TA-1-2RT 4-TA-1-4RT 4-TA-1-6RT 4-TA-1-8RT 5-TA-1-2RT 5-TA-1-4RT 6-TA-1-4RT 6-TA-1-6RT 6-TA-1-8RT 8-TA-1-4RT 8-TA-1-6RT 8-TA-1-8RT 10-TA-1-8RT

1/4 1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 1/2 1/2 1/2 5/8

1/8 1/4 3/8 1/2 1/8 1/4 1/4 3/8 1/2 1/4 3/8 1/2 1/2

1.25 1.46 1.44 1.66 1.29 1.50 1.50 1.50 1.72 1.72 1.75 1.94 2.06

.63 .63 .63 .63 .66 .66 .69 .69 .69 .91 .91 .91 .97

.38 .56 .56 .75 .38 .56 .56 .56 .75 .56 .56 .75 .75

7/16 9/16 11/16 7/8 7/16 9/16 9/16 11/16 7/8 9/16 11/16 7/8 7/8

.156 .156 .156 .219 .219 .219 .281 .281 .281 .375 .375 .375 .469

NOTE: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

Dimensions for reference only, subject to change.

MAK
BSP Taper Male Adapter
For metric tube
BSP

A K R

BSP

W HEX INTERCHANGES WITH MILLIMETERS TUBE O.D. BSP TR THREAD A K R W HEX BORE

PARKER PART NO.

M3MA1/8K M4MA1/8K M6MA1/8K M6MA1/4K M8MA1/4K M8MA3/8K M10MA1/4K M10MA3/8K M10MA1/2K M12MA1/4K M12MA3/8K M12MA1/2K M16MA1/2K M18MA3/4K M20MA3/4K M25MA1K

3-MTA-1-2RT 4-MTA-1-2RT 6-MTA-1-2RT 6-MTA-1-4RT 8-MTA-1-4RT 8-MTA-1-6RT 10-MTA-1-4RT 10-MTA-1-6RT 10-MTA-1-8RT 12-MTA-1-4RT 12-MTA-1-6RT 12-MTA-1-8RT 16-MTA-1-8RT 18-MTA-1-12RT 20-MTA-1-12RT 25-MTA-1-16RT

3 4 6 6 8 8 10 10 10 12 12 12 16 18 20 25

1/8 1/8 1/8 1/4 1/4 3/8 1/4 3/8 1/2 1/4 3/8 1/2 1/2 3/4 3/4 1

29,4 29,4 31,0 35,7 37,3 38,3 38,1 38,1 44,5 43,7 44,5 49,2 50,8 51,6 52,4 65,9

13,5 14,3 15,9 15,9 16,7 16,8 17,5 17,5 17,5 23,0 23,0 23,0 24,6 24,6 25,4 31,8

9,7 9,7 9,7 14,2 14,2 14,2 14,2 14,2 19,1 14,2 14,2 19,1 19,1 19,1 19,1 23,9

12,0 12,0 12,0 14,0 14,0 18,0 14,0 18,0 22,0 14,0 18,0 22,0 22,0 27,0 27,0 35,0

1,8 2,0 4,0 4,0 6,4 5,0 7,1 7,5 7,5 7,1 9,1 9,1 12,7 14,0 15,1 19,8

NOTE: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

Dimensions for reference only, subject to change.

41
Parker Hannifin Corporation

Port Connectors TUHA
Tube End to SAE Straight Thread Adapter
For fractional tube
PARKER PART NO. INTERCHANGES WITH T TUBE O.D. STRAIGHT THREAD SIZE INCHES W HEX O-RING APR UNIFORM DASH NO.

A

K

R

6TUHA4 6TUHA8 8TUHA6 10TUHA10 24TUHA24

6-TA-1-4ST 6-TA-1-8ST 8-TA-1-6ST 10-TA-1-10ST 24-TA-1-24ST

3/8 3/8 1/2 5/8 1-1/2

7/16-20 3/4-16 9/16-18 7/8-14 1-7/8-12

1.46 1.59 1.74 1.94 3.28

.69 .69 .91 .91 2.05

.36 .44 .39 .50 .59

9/16 7/8 11/16 1 2-1/8

3-904 3-908 3-906 3-910 3-924

NOTE: Preassembled with nut and ferrules. Dimensions for reference only, subject to change. A dimension is typical finger-tight. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

A R K

STRAIGHT THREAD

W HEX

FAN
Tube End NPT Female Adapter
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. NPT PIPE THREAD A K W HEX BORE

1FA2N 2FA2N 2FA4N 3FA2N 3FA4N 4FA2N 4FA4N 4FA6N 4FA8N 5FA2N 5FA4N 5FA6N 6FA2N 6FA4N 6FA6N 6FA8N 8FA4N 8FA6N 8FA8N 10FA6N 10FA8N 12FA8N 12FA12N 12FA16N 14FA12N 16FA12N 16FA16N 20FA20N 24FA24N 32FA32N

1-TA-7-2 2-TA-7-2 2-TA-7-4 3-TA-7-2 3-TA-7-4 4-TA-7-2 4-TA-7-4 4-TA-7-6 4-TA-7-8 5-TA-7-2 5-TA-7-4 5-TA-7-6 6-TA-7-2 6-TA-7-4 6-TA-7-6 6-TA-7-8 8-TA-7-4 8-TA-7-6 8-TA-7-8 10-TA-7-6 10-TA-7-8 12-TA-7-8 12-TA-7-12 12-TA-7-16 14-TA-7-12 16-TA-7-12 16-TA-7-16 20-TA-7-20 24-TA-7-24 32-TA-7-32

1/16 1/8 1/8 3/16 3/16 1/4 1/4 1/4 1/4 5/16 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 5/8 3/4 3/4 3/4 7/8 1 1 1-1/4 1-1/2 2

1/8 1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 1/8 1/4 3/8 1/8 1/4 3/8 1/2 1/4 3/8 1/2 3/8 1/2 1/2 3/4 1 3/4 3/4 1 1-1/4 1-1/2 2

1.07 1.23 1.38 1.25 1.42 1.31 1.47 1.56 1.80 1.34 1.50 1.59 1.36 1.55 1.59 1.84 1.72 1.80 2.10 1.86 2.09 2.10 2.16 2.30 2.22 2.41 2.54 3.06 3.50 4.23

.34 .53 .53 .56 .56 .63 .63 .63 .63 .66 .66 .66 .69 .69 .69 .69 .91 .91 .91 .97 .97 .97 .97 .97 1.02 1.22 1.22 1.71 2.05 2.74

9/16 9/16 3/4 9/16 3/4 9/16 3/4 7/8 1-1/16 9/16 3/4 7/8 9/16 3/4 7/8 1-1/16 3/4 7/8 1-1/16 7/8 1-1/16 1-1/16 1-1/4 1-5/8 1-5/16 1-5/16 1-5/8 2-1/8 2-3/8 2-7/8

.031 .093 .093 .116 .116 .188 .188 .188 .188 .219 .219 .219 .281 .281 .281 .281 .391 .391 .390 .469 .469 .578 .578 .578 .578 .813 .813 1.000 1.25 1.72

A K

BORE

W HEX

NOTE: Tube stub is pre-grooved as standard. Dimensions for reference only, subject to change. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

42
Parker Hannifin Corporation

Port Connectors FAN
Tube End NPT Female Adapter
For metric tube
PARKER PART NO. INTERCHANGES WITH MILLIMETERS TUBE O.D. NPT THREAD A K W HEX BORE

M3FA1/8N M4FA1/8N M6FA1/8N M6FA1/4N M8FA1/8N M8FA1/4N M8FA3/8N M10FA1/4N M10FA3/8N M10FA1/2N M12FA1/4N M12FA3/8N M12FA1/2N M16FA1/2N M18FA3/4N M20FA1/2N M20FA3/4N M25FA1N

3-MTA-7-2 4-MTA-7-2 6-MTA-7-2 6-MTA-7-4 8-MTA-7-2 8-MTA-7-4 8-MTA-7-6 10-MTA-7-4 10-MTA-7-6 10-MTA-7-8 12-MTA-7-4 12-MTA-7-6 12-MTA-7-8 16-MTA-7-8 18-MTA-7-12 20-MTA-7-8 20-MTA-7-12 25-MTA-7-16

3 4 6 6 8 8 8 10 10 10 12 12 12 16 18 20 20 25

1/8 1/8 1/8 1/4 1/8 1/4 3/8 1/4 3/8 1/2 1/4 3/8 1/2 1/2 3/4 1/2 3/4 1

31,3 29,4 29,4 34,1 35,5 35,1 36,5 37,3 37,3 42,1 41,3 42,9 47,6 49,2 52,4 50,0 53,2 66,7

13,5 14,3 15,9 15,9 16,7 16,7 16,7 17,5 17,5 17,5 23,0 23,0 23,0 24,6 24,6 25,6 25,4 31,8

14,0 14,0 14,0 19,0 14,0 19,0 22,0 19,0 22,0 27,0 19,0 22,0 27,0 27,0 33,0 27,0 33,0 41,0

1,3 2,0 4,0 4,0 6,4 6,4 6,4 7,5 7,5 7,5 9,1 9,1 9,1 12,7 14,0 15,0 15,1 19,8

A K

BORE

W HEX

NOTE: Tube stub is pre-grooved as standard. Dimensions for reference only, subject to change. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

FAK
BSP Taper Female Adapter
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. BSP TR THREAD A K W HEX BORE

4FA2K 4FA4K 6FA4K 6FA6K 8FA4K 8FA6K 8FA8K

4-TR-7-2RT 4-TR-7-4RT 6-TR-7-4RT 6-TR-7-6RT 8-TR-7-4RT 8-TR-7-6RT 8-TR-7-8RT

1/4 1/4 3/8 3/8 1/2 1/2 1/2

1/8-28 1/4-19 1/4-19 3/8-19 1/4-19 3/8-19 1/2-14

1.31 1.48 1.56 1.63 1.83 1.89 2.14

.64 .64 .72 .72 .98 .98 .98

9/16 3/4 3/4 7/8 3/4 7/8 1-1/16

.156 .156 .281 .281 .375 .375 .375

NOTE: Tube stub is pre-grooved as standard. Dimensions for reference only, subject to change. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end. A K

BORE

W HEX

FAK
BSP Taper Female Adapter
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. BSP TR THREAD A K W HEX BORE

M3FA1/8K M4FA1/8K M6FA1/8K M8FA1/4K M10FA1/4K M10FA3/8K M10FA1/2K M12FA1/4K M12FA3/8K M12FA1/2K M16FA1/2K M18FA3/4K M20FA3/4K M25FA1K

3-MTA-7-2RT 4-MTA-7-2RT 6-MTA-7-2RT 8-MTA-7-4RT 10-MTA-7-4RT 10-MTA-7-6RT 10-MTA-7-8RT 12-MTA-7-4RT 12-MTA-7-6RT 12-MTA-7-8RT 16-MTA-7-8RT 18-MTA-7-12RT 20-MTA-7-12RT 25-MTA-7-16RT

3 4 6 8 10 10 10 12 12 12 16 18 20 25

1/8 1/8 1/8 1/4 1/4 3/8 1/2 1/4 3/8 1/2 1/2 3/4 3/4 1

27,8 28,6 30,2 39,1 36,5 31,8 41,3 40,5 43,7 46,8 48,4 51,6 52,4 66,7

13,5 14,3 15,9 16,7 17,5 17,5 17,5 23,0 23,0 23,0 24,6 24,6 25,4 31,8

14,0 14,0 14,0 19,0 19,0 22,0 27,0 19,0 22,0 27,0 27,0 32,0 32,0 41,0

1,8 2,0 4,0 6,4 7,5 7,5 7,5 9,1 9,1 9,1 12,7 14,0 15,1 19,8

A K

BORE

NOTE: Tube stub is pre-grooved as standard. Dimensions for reference only, subject to change. Add -Z6 for assembly of nuts and ferrules on the tube stub end. W HEX

43
Parker Hannifin Corporation

Port Connectors FAR
BSPP Female Adapter
For fractional tube
BSPP

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. BSPP THREAD A K W HEX BORE

4FA4R 6FA6R 8FA8R

4-TA-7-4RP 6-TA-7-6RP 8-TA-7-8RP

1/4 3/8 1/2

1/4 3/8 1/2

1.47 1.53 1.91

.63 .69 .91

3/4 7/8 1-1/16

.18 .28 .39

NOTE: Copper washer must be used for this design. Dimensions for reference only, subject to change. Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

A K

BSPP

BORE

W HEX

FAR
BSPP Female Adapter
For metric tube
BSPP

PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. BSPP THREAD A K W HEX BORE

M3FA1/8R M3FA1/4R M4FA1/8R M6FA1/8R M6FA1/4R M8FA1/4R M10FA1/4R M10FA1/2R M12FA3/8R M12FA1/2R M16FA1/2R M18FA3/4R M20FA3/4R M25FA1R

3-MTA-7-2RP 3-MTA-7-4RP 4-MTA-7-2RP 6-MTA-7-4RP 6-MTA-7-4RP 8-MTA-7-4RP 10-MTA-7-4RP 10-MTA-7-8RP 12-MTA-7-6RP 12-MTA-7-8RP 16-MTA-7-8RP 18-MTA-7-12RP 20-MTA-7-12RP 25-MTA-7-16RP

3 3 4 6 6 8 10 10 12 12 16 18 20 25

1/8 1/4 1/8 1/8 1/4 1/4 1/4 1/2 3/8 1/2 1/2 3/4 3/4 1

28,6 28,6 29,4 31,0 37,3 38,1 38,9 43,7 44,5 48,4 50,0 53,2 54,0 67,5

13,5 13,7 14,3 15,9 15,9 16,7 17,5 17,5 23,0 23,0 24,6 24,6 25,4 31,8

14,0 19,0 14,0 14,0 19,0 19,0 19,0 27,0 22,0 27,0 27,0 33,0 33,0 41,0

1,8 1,6 2,0 4,0 4,0 6,4 7,5 7,5 9,1 9,1 12,7 14,0 15,1 19,8

A K

BSPP

BORE

W HEX

NOTE: Copper washer must be used for this design. Dimensions for reference only, subject to change. Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

P2TU
Push-Lok to Tube Adapter
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES T1 TUBE O.D. T2 HOSE SIZE A K W HEX

4-4 P2TU 6-6 P2TU 8-8 P2TU

PB4-TA4 PB6-TA6 PB8-TA8

1/4 3/8 1/2

–4 –6 –8

1.80 2.02 2.42

.64 .72 .98

7/16 9/16 11/16

NOTE: Drawing does not show Push-Lok collar. Dimensions for reference only, subject to change. Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department. Add -Z6 for assembly of nuts and ferrules on the tube stub end.

A K T1 TURNED END TUBE O.D. W HEX T2 MACHINED END TUBE O.D.

44
Parker Hannifin Corporation

Port Connectors P2HF
Push-Lok to Male Adapter
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES T1 T2 NPT PIPE THREAD HOSE SIZE A B R W HEX

4-4 P2HF

PB4-PM4

–4

1/4

1.65

.80

.56

9/16

NOTE: Drawing does not show Push-Lok collar.

Dimensions for reference only, subject to change.

A R T2 B

T1

W HEX

P2LZ6
Push-Lok to A-LOK
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES T2 TUBE O.D. T1 HOSE SIZE A K W HEX

4-4 P2LZ6 6-6 P2LZ6 8-8 P2LZ6

PB4-TA4 PB6-TA6 PB8-TA8

1/4 3/8 1/2

–4 –6 –8

1.77 1.98 2.42

.72 .78 1.03

7/16 9/16 11/16

NOTE: A dimension is typical finger-tight. Dimensions for reference only, subject to change. Drawing does not show Push-Lok collar. Assembly includes nut and ferrules.

A K

T1

T2 MACHINED END TUBE O.D.

W HEX

ZP2
Push-Lok to Port Connector
For fractional tube
PARKER PART NO. T1 HOSE SIZE T2 PORT SIZE

INCHES A B

4-6 ZP2

–4

3/8

1.40

.80

Dimensions for reference only, subject to change. NOTE: Drawing does not show Push-Lok collar and size 6 A-LOK nut.

A B T1 T2 MACHINED END TUBE O.D.

45
Parker Hannifin Corporation

Port Connectors LJF
Lapped Joint Tube Adapters
For metric tube
PARKER PART NO. INTERCHANGES WITH MILLIMETERS TUBE O.D. FLANGE SIZE A D L R SURFACE FINISH

M10LJF-5 M10LJF-9 M12LJF-5 M12LJF-9

10M0-1-0005 10M0-1-0006 – –

10 10 12 12

DN15(12"NB) DN15(12"NB) DN15(12"NB) DN15(12"NB)

83,0 83,0 85,0 85,0

34,5 34,5 34,5 34,5

75,5 75,5 75,4 75,4

6,5 6,5 6,5 6,5

Smooth Rough Smooth Rough

3,2-6,3 Ra 6,3-12,5 Ra 3,2-6,3 Ra 6,3-12,5 Ra

NOTE: Groove on flange diameter indicates rough finish.

Dimensions for reference only, subject to change.

The lapped joint tube adaptor is a fitting designed to be used with a lap joint flange which enables a direct hookup to the instrument tube from the process line. The compression fitting is incorporated into the body of the adaptor thus the number of components needed for hook-up is reduced. It is therefore cost efficient as well as space saving. Note Groove on flange diameter indicates rough finish. The face of the fitting forms the gasket face of the flange and comes with either a smooth or serrated surface finish. Adapters to suit other tube and flange sizes may be furnished upon request.

D

R

L A

ZH2X
DP Transmitter Calibration Adapters
For fractional tube
Parker A-LOK adapters connect directly to the bleed port of a differential pressure transmitter so that the calibration process can be simplified. Two sizes of adapters (1/4-28 Thd., 5/16-24 Thd.) are available to fit the vent ports of Rosemount, Honeywell, and Foxboro DP transmitters. Both adapters are available in 316SS.

TRANSMITTER TYPE Rosemount/Foxboro Honeywell

PARKER PART NO. 4-2 ZH2LX-SS-D950373 4-2 ZH2LX-SS-D940336

INTERCHANGES WITH SS-400-1-0253 SS-400-1-0257

INCHES STRAIGHT THREAD A B C D E F G H J HEX

1/4-28 5/16-24

1.75 2.32

.80 1.00

.70 .70

1.46 2.03

.47 .24

.60 .60

.20 .25

.03 .06

– .41

1/2 1/2

Dimensions for reference only, subject to change.

A D J 9/16 HEX
1/4 TUBE

A B H G E STRAIGHT THREAD 1/2 BODY HEX 9/16 1/4 TUBE HEX F C D B E H G STRAIGHT THREAD 1/2 BODY HEX

F C

Calibration Adapter For Rosemount/Foxboro DP Transmitters 46

Calibration Adapter For Honeywell DP Transmitters

Parker Hannifin Corporation

37° Flare (AN) to A-LOK X6TU
37° Flare (AN) to A-LOK
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. D W HEX

2X6TU2 4X6TU4 6X6TU6 8X6TU8 12X6TU12 16X6TU16

200-A-2 ANF 400-A-4 ANF 600-A-6 ANF 810-A-8 ANF 1210-A-12ANF 1610-A-16ANF

1/8 1/4 3/8 1/2 3/4 1

.88 .96 1.07 1.37 1.49 1.80

3/8 9/16 11/16 7/8 1-1/4 1-1/2

Dimensions for reference only, subject to change.

W HEX

D

XASC
37° Flare Connector
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES FLARE END TUBE O.D. A B C D W HEX

2XASC1 2XASC2 4XASC2 3XASC3 4XASC4 5XASC5 4XASC6 6XASC6 8XASC8 10XASC10

100-6-2 AN 200-6-2 AN 200-6-4 AN 300-6-3 AN 400-6-4 AN 500-6-5 AN 600-6-4 AN 600-6-6 AN 810-6-8 AN 1010-6-10 AN 1210-6-12 AN 1610-6-16 AN

1/8 1/8 1/4 3/16 1/4 5/16 1/4 3/8 1/2 5/8 3/4 1

1/16 1/8 1/8 3/16 1/4 5/16 3/8 3/8 1/2 5/8 3/4 1

1.07 1.28 1.39 1.32 1.48 1.52 1.56 1.56 1.81 1.93 2.11 2.43

.45 .45 .55 .48 .55 .55 .55 .56 .66 .76 .86 .91

.43 .60 .60 .64 .70 .73 .76 .76 .87 .87 .87 1.05

.92 1.02 1.13 1.06 1.19 1.22 1.27 1.27 1.41 1.53 1.70 1.94

7/16 7/16 1/2 7/16 1/2 9/16 5/8 5/8 13/16 15/16 1-1/8 1-3/8

A D B C

12XASC12 16XASC16

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

W HEX

XABC
37° Flare Bulkhead Connector
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES FLARE END TUBE O.D. A D C L B W HEX

2XABC2 4XABC2 3XABC3 4XABC4 5XABC5 4XABC6 6XABC6 8XABC8 10XABC10 12XABC12 16XABC16

200-61-2 AN 200-61-4 AN 300-61-3 AN 400-61-4 AN 500-61-5 AN 600-61-4 AN 600-61-6 AN 810-61-8 AN 1010-61-10 AN 1210-61-12 AN 1610-61-16 AN

1/8 1/4 3/16 1/4 5/16 1/4 3/8 1/2 5/8 3/4 1

1/8 1/8 3/16 1/4 5/16 3/8 3/8 1/2 5/8 3/4 1

1.91 2.04 1.98 2.12 2.21 2.25 2.25 2.59 2.74 3.11 3.65

1.65 1.78 1.71 1.83 1.92 1.96 1.96 2.19 2.34 2.71 3.16

1.23 1.23 1.26 1.31 1.41 1.44 1.44 1.65 1.68 1.87 2.27

.97 .97 1.00 1.02 1.12 1.15 1.15 1.25 1.28 1.47 1.78

.45 .55 .48 .55 .55 .55 .56 .66 .76 .86 .91

1/2 5/8 9/16 5/8 11/16 3/4 3/4 15/16 1-1/16 1-3/16 1-9/16

A D B C L

NOTE: A and C dimensions are typical finger-tight. Dimensions for reference only, subject to change. For bulkhead hole drill size and maximum bulkhead thickness, see Page 28, Part BC

W HEX

47
Parker Hannifin Corporation

Tube to “O” Ring Seal
Introduction BSPP SAE Straight Thread Fittings Installation Procedure
1. Lubricate “O” ring with a lubricant that is compatible with the system. 2. Screw fitting into the straight thread port until the metal back-up washer contacts the face of the port. 3. Position the fitting by backing it out no more than one turn. 4. Hold the fitting in position and tighten the locknut until the washer contacts the face of the port. (See torque chart.) NOTE: WLN Lock Nuts are ordered separately by size and part number. Refer to page 73. Straight Port Size 4 6 8 10 12 16 20 24 Torque (in-lbs) 245 ± 10 630 ± 25 1150 ± 50 1550 ± 50 2050 ± 50 3000 ± 50 3400 ± 100 4500 ± 100 (F.F.F.T.) 1.0 ± .25 1.5 ± .25 1.5 ± .25 1.5 ± .25 1.5 ± .25 1.5 ± .25 1.5 ± .25 1.5 ± .25

WLN LOCK NUT

WASHER “O” RING

Adjustable Port Torque (in-lbs) 200 ± 10 400 ± 10 640 ± 10 1125 ± 50 1450 ± 50 2150 ± 50 2800 ± 100 3450 ± 100 (F.F.F.T) 1.5 ± 25 1.5 ± 25 1.5 ± 25 1.5 ± 25 1.5 ± 25 1.5 ± 25 2.0 ± 25 2.0 ± 25

NOTES Restrain fitting body on adjustables if necessary in installation. Values in charts are for assemblies with O-ring lubricated. Use upper limits of torque ranges for stainless steel fittings.

Face Seal “O” Ring Fittings Installation Procedure
The “O” ring requires a smooth, flat seating surface.This surface must be perpendicular to the axis of the threads. 1. Turn the “O” ring seal fitting in the port until finger tight. 2. The “squeezing” effect on the “O” ring can be felt during the last 1/4 turn. 3. Snug lightly with a wrench.

L5N LOCK NUT

Typical Application
The fitting can be adapted as a bulkhead fitting on thin wall tanks or vessels, eliminating welding, brazing or threading. Simply order the L5N locknut to take advantage of this option.
PORT SIZE STRAIGHT THREAD MACHINE LENGTH L5N LOCKNUT THICKNESS MAXIMUM TANK WALL THICKNESS

Notes
Standard “O” rings are Buna-N material. For other “O” rings, state material after the part number. L5N locknuts are ordered separately by size and part number. Refer to page 73.

2 3 4 5 6 8 10 12 14 16

.297 .297 .360 .360 .391 .438 .500 .594 .594 .594

.219 .219 .250 .250 .265 .312 .360 .406 .406 .406

.078 = 5/64 .078 = 5/64 .109 = 7/65 .109 = 7/64 .125 = 1/8 .125 = 1/8 .140 = 9/64 .188 = 3/16 .188 = 3/16 .188 = 3/16

O-rings used with SAE/MS straight threads are Buna-N. Other O-ring materials are available on request. Lubricate O-ring with a lubricant compatible with the system fluid, environment and O-ring material.

48
Parker Hannifin Corporation

Tube to “O” Ring Seal M1SC
Male Connector to SAE Straight Thread
For fractional tube
W HEX INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. STRAIGHT THREAD SIZE W HEX “O” RING O-RING AS UNIFORM DASH NO. C A D R

A

C

D

R

1M1SC2 2M1SC2 2M1SC6 3M1SC3 4M1SC4 4M1SC6 4M1SC8 4M1SC10 5M1SC5 6M1SC4 6M1SC6 6M1SC8 6M1SC10 8M1SC6 8M1SC8 8M1SC12 10M1SC10 12M1SC10 12M1SC12 14M1SC14 16M1SC12 16M1SC16 20M1SC20 24M1SC24 32M1SC32

100-1-2 ST 200-1-2 ST 200-1-6 ST 300-1-3 ST 400-1-4 ST 400-1-6 ST 400-1-8 ST 400-1-10 ST 500-1-5 ST 600-1-4 ST 600-1-6 ST 600-1-8 ST 600-1-10 ST 810-1-6 ST 810-1-8 ST 810-1-12 ST 1010-1-10 ST 1210-1-10 ST 1210-1-12 ST 1410-1-14 ST 1610-1-12 ST 1610-1-16 ST 2010-1-20 ST 2410-1-24 ST 3210-1-32 ST

1/16 1/8 1/8 3/16 1/4 1/4 1/4 1/4 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 3/4 3/4 7/8 1 1 1-1/4 1-1/2 2

5/16-24 5/16-24 9/16-18 3/8-24 7/16-20 9/16-18 3/4-16 7/8-14 1/2-20 7/16-20 9/16-18 3/4-16 7/8-14 9/16-18 3/4-16 1-1/16-12 7/8-14 7/8-14 1-1/16-12 1-3/16-12 1-1/16-12 1-5/16-12 1-5/8-12 1-7/8-12 2-1/2-12

.92 1.18 1.35 1.20 1.34 1.40 1.48 1.60 1.37 1.40 1.46 1.54 1.67 1.54 1.65 1.93 1.78 1.68 1.93 1.93 2.12 2.15 2.59 3.05 4.00

.43 .60 .60 .64 .70 .70 .70 .70 .73 .76 .76 .76 .76 .87 .87 .87 .87 .87 .87 .87 1.05 1.04 1.52 1.77 2.47

.77 .92 1.06 .94 1.05 1.11 1.19 1.31 1.08 1.11 1.17 1.25 1.38 1.14 1.25 1.53 1.38 1.28 1.53 1.53 1.63 1.66 1.82 1.99 2.53

.30 .30 .39 .30 .36 .39 .44 .50 .36 .36 .39 .44 .50 .39 .44 .59 .50 .50 .59 .59 .59 .59 .59 .59 .59

7/16 7/16 11/16 1/2 9/16 11/16 7/8 1 5/8 5/8 11/16 7/8 1.00 7/8 7/8 1-1/4 1 1-1/8 1-1/4 1-3/8 1-3/8 1-1/2 1-7/8 2-1/8 2-3/4

3-902 3-902 3-906 3-903 3-904 3-906 3-908 3-910 3-905 3-904 3-906 3-908 3-910 3-906 3-908 3-912 3-910 3-910 3-912 3-914 3-912 3-916 3-920 3-924 3-932

NOTE: A and C dimensions are typical finger-tight. For use with SAE J.1926/1 port can also be used with MS-16142 port.

Dimensions for reference only, subject to change.

49
Parker Hannifin Corporation

Tube to “O” Ring Seal M5SEL
Male SAE Straight Thread Elbow
For fractional tube
H WLN BACKUP WASHER “O” RING STRAIGHT THREAD INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. STRAIGHT THREAD SIZE W HEX R C L W HEX

C

H

L

R

O-RING ARP UNIFORM DASH NO.

4M5SEL4 6M5SEL6 8M5SEL8 12M5SEL12 16M5SEL16 24M5SEL24

400-2-4ST 600-2-6ST 810-2-8ST 1210-2-12ST 1610-2-16ST 2410-2-24ST

1/4 3/8 1/2 3/4 1 1-1/2

7/16-20 9/16-18 3/4-16 1-1/16-12 1-5/16-12 1-7/8-12

1.12 1.26 1.48 1.63 1.87

1.13 1.27 1.48 1.92 2.11 2.33

.83 .97 1.08 1.23 1.38 2.00

.83 .84 .97 1.28 1.28 1.16

1/2 9/16 3/4 1-1/16 1-5/16 1-7/8

3-904 3-906 3-908 3-912 3-916 3-924

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

MSEL (R)
BSPP Male Elbow (Positionable)
For fractional tube
L4N

C L W HEX

“O” RING STRAIGHT THREAD INCHES TUBE O.D. BSPP THREAD C H L R W HEX

PARKER PART NO.

INTERCHANGES WITH

4MSEL2R 4MSEL4R 6MSEL4R 6MSEL6R 8MSEL4R 8MSEL6R 8MSEL8R 10MSEL8R 12MSEL8R 12MSEL12R 16MSEL12R 16MSEL16R

400-2-2PR 400-2-4PR 600-2-4PR 600-2-6PR 810-2-4PR 810-2-6PR 810-2-8PR 1010-2-8PR 1210-2-8PR 1210-2-12PR 1610-2-12PR 1610-2-16PR

1/4 1/4 3/8 3/8 1/2 1/2 1/2 5/8 3/4 3/4 1 1

1/8-28 1/4-19 1/4-19 3/8-19 1/4-19 3/8-19 1/2-14 1/2-14 1/2-14 3/4-14 3/4-14 1-11

1.14 1.31 1.31 1.50 1.50 1.48 1.50 1.50 1.57 1.57 1.94 1.94

1.25 1.27 1.27 1.46 1.38 1.46 1.70 1.81 1.81 1.92 2.11 2.11

.85 .85 1.02 1.02 1.10 1.10 1.10 1.10 1.17 1.17 1.45 1.45

.81 .83 .83 .83 .83 .85 1.09 1.09 1.09 1.20 1.20 1.20

NOTE: C dimension is typical finger-tight. Connects fractional tube to female ISO parallel thread.

Dimensions for reference only, subject to change.

50
Parker Hannifin Corporation

BSPP
BSPP

H R

9/16 9/16 9/16 3/4 7/8 7/8 7/8 1-1/16 1-1/16 1-1/16 1-5/16 1-5/16

Tube to “O” Ring Seal M5RT
Male Run Tee SAE Straight Thread
For fractional tube
W HEX WLN “O” RING A C L H R STRAIGHT THREAD

BACKUP WASHER

INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. STRAIGHT THREAD SIZE W HEX

A

C

H

L

R

O-RING ARP UNIFORM DASH NO.

4M5RT4 6M5RT6 8M5RT8 12M5RT12 16M5RT16

400-3TST 600-3TST 810-3TST 1210-3TST 1610-3TST

1/4 3/8 1/2 3/4 1

7/16-20 9/16-18 3/4-16 1-1/16-12 1-5/16-12

2.25 2.53 3.59 3.55 3.98

1.12 1.26 1.48 1.63 1.87

1.13 1.27 1.48 1.92 2.11

.83 .97 1.08 1.23 1.38

.83 .84 .97 1.28 1.28

7/16 9/16 3/4 1-1/16 1-5/16

3-904 3-906 3-908 3-912 3-916

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

MRT (R)
BSPP Male Run Tee (Positionable)
For fractional tube
BSPP

C L

H R

BSPP

W

L4N

“O” RING

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. BSPP THREAD C H L R W HEX

4MRT2R 4MRT4R 6MRT6R 8MRT8R 8MRT8R 10MRT8R 12MRT8R 12MRT12R 16MRT16R

400-3TRT 400-3-4TRT 600-3TRT 810-3TRT 810-3-8TRT 1010-3TRT 1210-3-8TRT 1210-3TRT 1610-3TRT

1/4 1/4 3/8 1/2 1/2 5/8 3/4 3/4 1

1/8-28 1/4-19 1/4-19 3/8-19 1/2-14 1/2-14 1/2-14 3/4-14 1-11

1.14 1.14 1.31 1.50 1.50 1.50 1.567 1.57 1.94

1.25 1.28 1.27 1.36 1.71 1.81 1.81 1.92 2.11

.85 .85 1.02 1.10 1.10 1.10 1.17 1.17 1.45

.81 .83 .83 .85 1.09 1.09 1.09 1.20 1.20

9/16 9/16 9/16 7/8 7/8 1-1/16 1-1/16 1-1/16 1-5/16

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

51
Parker Hannifin Corporation

Tube to “O” Ring Seal
A

M5BT
Male Branch Tee SAE Straight Thread
For fractional tube

C L

W HEX WLN “O” RING STRAIGHT THREAD INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. STRAIGHT THREAD SIZE W HEX R BACKUP WASHER H

A

C

H

L

R

O-RING ARP UNIFORM DASH NO.

4M5BT4 6M5BT6 8M5BT8 12M5BT12 16M5BT16

400-3TTS 600-3TTS 810-3TTS 1210-3TTS 1610-3TTS

1/4 3/8 1/2 3/4 1

7/16-20 9/16-18 3/4-16 1-1/16-12 1-5/16-12

2.24 2.52 2.96 3.26 3.74

1.12 1.26 1.48 1.63 1.87

1.13 1.27 1.48 1.92 2.11

.83 .97 1.08 1.23 1.38

.83 .84 .97 1.28 1.28

7/16 9/16 3/4 1-1/16 1-5/16

3-904 3-906 3-908 3-912 3-916

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

C

MBT (R)
BSPP Male Branch Tee (Positionable)
BSPP

L

W HEX H L4N “O” RING R

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. BSPP THREAD C H L R W HEX

4MBT2R 4MBT4R 6MBT4R 8MBT6R 8MBT8R 10MBT8R 12MBT8R 12MBT12R 16MBT16R

400-3TTR 400-3-4TTR 600-3TTR 810-3TTR 810-3-8TTR 1010-3TTR 1210-3-8TTR 1210-3-TTR 1610-3TTR

1/4 1/4 3/8 1/2 1/2 5/8 3/4 3/4 1

1/8-28 1/4-19 1/4-19 3/8-19 1/2-14 1/2-14 1/2-14 3/4-14 1-11

1.14 1.14 1.31 1.50 1.50 1.50 1.57 1.57 1.94

1.25 1.27 1.27 1.36 1.71 1.81 1.81 1.92 2.11

.85 .85 1.02 1.10 1.10 1.10 1.17 1.17 1.45

NOTE: C dimension is typical finger-tight. Connects fractional tube to female ISO parallel thread.

Dimensions for reference only, subject to change.

52
Parker Hannifin Corporation

BSPP

For fractional tube

.81 .83 .83 .85 1.09 1.09 1.09 1.20 1.20

9/16 9/16 9/16 7/8 7/8 1-1/16 1-1/16 1-1/16 1-5/16

Tube to “O” Ring Seal ZH3LA
Long Male Connector SAE/MS Straight Thread
For fractional tube
W HEX INCHES PARKER PART NO. INTERCHANGES WITH T TUBE O.D. S-SAE/MS THREAD SIZE E MIN. OPENING W HEX “O” RING ST O-RING UNIFORM SIZE NO. A D C R

A

R

C

D

4-4 ZH3LA 400-1L-4ST 6-6 ZH3LA 600-1L-6ST 8-8 ZH3LA 810-1L-8ST 12-12 ZH3LA 1210-1L-12ST 16-16 ZH3LA 1610-1L-16ST

1/4 3/8 1/2 3/4 1

7/16-20 9/16-18 3/4-16 1-1/16-12 1-5/16-12

2.26 2.48 3.01 3.88 4.34

.36 .39 .44 .59 .59

.70 .76 .86 .86 1.04

1.97 2.19 2.58 3.48 3.86

.19 .28 .41 .62 .88

9/16 11/16 7/8 1-1/4 1-1/2

-904 -906 -908 -912 -916

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

C

M5VEL
45° Positionable Male Elbow SAE/MS Straight Thread
For fractional tube

L W HEX

H

R

INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. STRAIGHT THREAD SIZE W HEX

C

H

L

R

O-RING UNIFORM SIZE NUMBER

4M5VEL4 6M5VEL6 8M5VEL8 12M5VEL12 16M5VEL16

400-5-4ST 600-5-6ST 810-5-8ST 1210-5-12ST 1610-5-16ST

1/4 3/8 1/2 3/4 1

7/16-20 9/16-18 3/4-16 1-1/16-12 1-5/16-12

.93 1.01 1.15 1.63 1.87

1.02 1.27 1.48 1.92 2.11

.65 .72 .75 1.23 1.39

.75 .77 .88 1.16 1.16

7/16 9/16 3/4 1-1/16 1-5/16

3-904 3-906 3-908 3-912 3-916

NOTE: C dimension is typical finger-tight. Adapts to SAE J1926 straight thread boss and MS16142 boss.

Dimensions for reference only, subject to change.

53
Parker Hannifin Corporation

Tube to “O” Ring Seal M2SC
Male Connector to “O” Ring Straight Thread
For fractional tube
W HEX INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. STRAIGHT THREAD SIZE W HEX A D C R

X

STRAIGHT THREAD

A

C

D

R

X DIA.

O-RING ARP UNIFORM DASH NO.

1M2SC2 2M2SC2 3M2SC3 4M2SC4 5M2SC5 6M2SC6 8M2SC8 10M2SC10 12M2SC12 14M2SC12 16M2SC16

100-1-OR 200-1-OR 300-1-OR 400-1-OR 500-1-OR 600-1-OR 810-1-OR 1010-1-OR 1210-1-OR 1410-1-OR 1610-1-OR

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1

5/16-24 5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1-1/16-12 1-1/16-12 1-5/16-12

1.06 1.29 1.35 1.51 1.61 1.67 1.81 1.90 2.06 2.06 2.30

.43 .60 .64 .70 .73 .76 .87 .87 .87 .87 1.05

.91 1.03 1.09 1.22 1.31 1.38 1.41 1.50 1.66 1.66 1.81

.34 .34 .38 .41 .44 .44 .47 .47 .56 .56 .56

.55 .55 .62 .74 .86 .93 1.12 1.30 1.49 1.49 1.74

9/16 9/16 5/8 3/4 7/8 15/16 1-1/8 1-3/8 1-1/2 1-1/2 1-3/4

2-011 2-011 2-012 2-111 2-112 2-113 2-116 2-212 2-215 2-215 2-219

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

M3SC
Male Connector to “O” Ring Pipe Thread
For fractional tube

A D C R

X

W HEX INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. STRAIGHT THREAD SIZE W HEX

PIPE THREAD O-RING ARP UNIFORM DASH NO.

A

C

D

R

X DIA.

1M3SC2 2M3SC2 2M3SC4 3M3SC2 3M3SC4 4M3SC2 4M3SC4 4M3SC6 5M3SC2 5M3SC4 6M3SC2 6M3SC4 6M3SC6 6M3SC8 8M3SC4 8M3SC6 8M3SC8 10M3SC8 10M3SC12 12M3SC8 12M3SC12 16M3SC12 16M3SC16

100-1-2-OR 200-1-2-OR 200-1-4-OR 300-1-2-OR 300-1-4-OR 400-1-2-OR 400-1-4-OR 400-1-6-OR 500-1-2-OR 500-1-4-OR 600-1-2-OR 600-1-4-OR 600-1-6-OR 600-1-8-OR 810-1-4-OR 810-1-6-OR 810-1-8-OR 1010-1-8-OR 1010-1-8-OR 1210-1-8-OR 1210-1-12-OR 1610-1-12-OR 1610-1-16-OR

1/16 1/8 1/8 3/16 3/16 1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 5/8 3/4 3/4 1 1

1/8 1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/8 1/4 1/8 1/4 3/8 1/2 1/4 3/8 1/2 1/2 3/4 1/2 3/4 3/4 1

1.12 1.29 1.43 1.32 1.46 1.38 1.51 1.57 1.43 1.46 1.45 1.57 1.63 1.85 1.68 1.76 1.98 1.96 2.06 1.98 2.06 2.24 2.40

.43 .60 .60 .64 .64 .70 .70 .70 .73 .73 .76 .76 .76 .76 .87 .87 .87 .87 .87 .87 .87 1.05 1.05

.97 1.03 1.17 1.06 1.20 1.09 1.22 1.28 1.13 1.25 1.16 1.28 1.34 1.56 1.28 1.36 1.58 1.56 1.66 1.58 1.66 1.75 1.91

.28 .28 .38 .28 .38 .28 .38 .41 .28 .38 .28 .38 .41 .53 .38 .41 .53 .53 .56 .53 .56 .56 .66

.74 .74 .93 .74 .93 .74 .93 1.12 .74 .93 .74 .93 1.12 1.30 .93 1.12 1.30 1.30 1.49 1.30 1.49 1.49 1.74

3/4 3/4 15/16 3/4 15/16 3/4 15/16 1-1/8 3/4 15/16 3/4 15/16 1-1/8 1-3/8 15/16 1-1/8 1-3/8 1-3/8 1-1/2 1-3/8 1-1/2 1-1/2 1-3/4

2-011 2-011 2-113 2-011 2-113 2-011 2-113 2-116 2-011 2-113 2-011 2-113 2-116 2-212 2-113 2-116 2-212 2-212 2-215 2-212 2-215 2-215 2-219

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

54
Parker Hannifin Corporation

Tube to “O” Ring Seal
A

M2TU
Tube End to “O” Ring Straight Thread
For fractional tube
T

K

R

X

W HEX

STRAIGHT THREAD O-RING ARP UNIFORM DASH NO.

INCHES PARKER PART NO. INTERCHANGES WITH T TUBE O.D. STRAIGHT THREAD SIZE X DIA. W HEX

A

K

R

2M2TU2 3M2TU3 4M2TU4 5M2TU5 6M2TU6 8M2TU8 10M2TU10 12M2TU12 16M2TU16

2-TA-OR-ST 3-TA-OR-ST 4-TA-OR-ST 5-TA-OR-ST 6-TA-OR-ST 8-TA-OR-ST 10-TA-OR-ST 12-TA-OR-ST 16-TA-OR-ST

1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1-1/16-12 1-5/16-12

1.22 1.38 1.55 1.64 1.70 1.95 2.12 2.16 2.47

.53 .56 .63 .66 .69 .91 .97 .97 1.22

.34 .38 .41 .44 .47 .47 .47 .56 .56

.55 .62 .74 .86 .93 1.12 1.30 1.49 1.74

9/16 5/8 3/4 7/8 15/16 1-1/8 1-3/8 1-1/2 1-3/4

2-011 2-012 2-111 2-112 2-113 2-116 2-212 2-215 2-219

NOTE: Add -Z6 for assembly of nuts and ferrules on the tube stub end.

Dimensions for reference only, subject to change.

M3TU
Tube End to “O” Ring Pipe Thread
For fractional tube
T K

A R

X

W HEX INCHES PARKER PART NO. INTERCHANGES WITH T TUBE O.D. NPT PIPE THREAD X DIA. W HEX

PIPE THREAD O-RING ARP UNIFORM DASH NO.

A

K

R

1M3TU2 4M3TU2 4M3TU4 4M3TU6 5M3TU2 5M3TU4 6M3TU2 6M3TU4 6M3TU6 8M3TU6 10M3TU8 12M3TU12 16M3TU16

1-TA-1-20R 4-TA-1-2OR 4-TA-1-4OR 4-TA-1-6OR 5-TA-1-2OR 5-TA-1-4OR 6-TA-1-2OR 6-TA-1-4OR 6-TA-1-6OR 8-TA-1-6OR 10-TA-1-8OR 12-TA-1-12OR 16-TA-1-16OR

1/16 1/4 1/4 1/4 5/16 5/16 3/8 3/8 3/8 1/2 5/8 3/4 1

1/8 1/8 1/4 3/8 1/8 1/4 1/8 1/4 3/8 3/8 1/2 3/4 1

1.03 1.31 1.44 1.50 1.34 1.47 1.38 1.50 1.59 1.78 2.14 2.16 2.56

.34 .63 .63 .63 .66 .66 .69 .69 .69 .91 .97 .97 1.22

.28 .28 .38 .41 .28 .38 .28 .38 .41 .41 .53 .56 .66

.74 .74 .93 1.12 .74 .93 .74 .93 1.12 1.12 1.30 1.49 1.65

3/4 3/4 15/16 1-1/8 3/4 15/16 3/4 15/16 1-1/8 1-1/8 1-3/8 1-1/2 1-3/4

2-111 2-111 2-113 2-116 2-111 2-113 2-111 2-113 2-116 2-116 2-212 2-215 2-219

NOTE: Add -Z6 for assembly of nuts and ferrules on the tube stub end.

Dimensions for reference only, subject to change.

55
Parker Hannifin Corporation

Tube to “O” Ring Seal FHOA
Pipe Thread to SAE Straight Thread Adapter
For fractional tube
PARKER PART NO. INTERCHANGES WITH T2 STRAIGHT THREAD NPT T1 PIPE THREAD A INCHES W HEX O-RING AS UNIFORM DASH NO.

R1

R2

4-4 FHOA 4SAE-1-4 1/4-18 7/16-20 6-6 FHOA 6-SAE-1-6 3/8-18 9/16-18 8-8 FHOA 8-SAE-1-8 1/2-14 3/4- 16 12-12 FHOA 12-SAE-1-12 3/4-14 1-1/16-12 16-16 FHOA 16-SAE-1-16 1-11-1/2 1-5/16-12
NOTE: A and C dimensions are typical finger-tight. For use with SAE J.1926/1 port can also be used with MS-16142 port.

1.20 1.26 1.53 1.75 2.00

.56 .56 .75 .75 .94

.36 .39 .44 .59 .59

9/16 11/16 7/8 1-1/4 1-1/2

3-904 3-906 3-908 3-912 3-916

Dimensions for reference only, subject to change.

A R1 T1 PIPE THREAD R2 “O” RING T2 STRAIGHT THREAD W HEX

AH2LZ
Bulkhead to Conversion Adapter
For fractional tube

A C L R

“O” RING D

INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. STRAIGHT THREAD SIZE W HEX BULKHEAD HOLD DRILL SIZE MAX. BULKHEAD THICKNESS

A

C

D

R

L

4-6 AH2LZ 6-6 AH2LZ

400-61-6ST 600-61-6ST

1/4 3/8

9/16-18 9/16-18

1.74 1.81

1.17 1.24

1.45 1.52

.39 .39

.88 .94

3/4 3/4

37/64 37/64

9/16 9/16

NOTE: A and C dimensions are typical finger-tight. For use with SAE J.1926/1 port can also be used with MS-16142 port.

Dimensions for reference only, subject to change.

56
Parker Hannifin Corporation

Tube to Welded Systems
General
The weld used in joining a tube to a socket weld tube fitting is like any other type of “tee” weld. The root (i.e., the point of intersection of the outside of the tube and annular end area of the fitting) must be included in the weld zone. Careful welding procedures are normally followed to assure that this root area is included in the weld. If penetration is not achieved, the joint will have two built-in stress risers which may greatly reduce the strength of the weld. Upon application of an extreme load, these stress risers could result in cracks which could propagate out through the weld or tube depending upon the direction of the greatest load. Often to achieve full root penetration in TIG welding of stainless steels, a fusion pass will be made first, followed by a final pass utilizing a filler rod to achieve the desired fillet size.

Welding Methods 300 Series Stainless Steels
May be welded by the TIG, MIG, or stick arc-weld process. TIG welding is recommended as being best for welding Weld-lok systems because it allows better operator control of heat penetration and filler material deposition. Stick arc welding is not recommended in many cases because of the likelihood of excessive burn-through and improper root penetration. In all cases where stick welding is used, it is recommended that backing gas be used. MIG welding gives the same characteristics as stick electrode welding with faster deposition of the filler material. As this process runs “hotter” than the stick process, the use of a backing gas is mandatory. It should be noted that in welding the relatively small fitting sizes found in the Weld-lok line, filler deposition rate economies are not a factor and therefore the MIG method is not commonly applied.

Assembly
The codes applicable to the welding of socket weld fittings require that the tube be inserted into the socket until bottomed against the stop. The tube is then to be backed out approximately 1/16 of an inch and then welded. If the tube is not backed out, but welded when against a flat bottom stop, the contraction of the weld fillet and fitting socket can combine to produce a static stress on the weld. During thermal transients, the fitting and the portion of the tube within the fitting may experience a differential rate of heating or cooling, again adding to the stress level in the weld.

C1018 Steel Fittings
May be welded by the TIG, MIG, stick and oxyacetylene methods. As scale formation remains a problem, the use of a backing gas is still recommended.

Carbide Precipitation
When unstabilized stainless steels are heated to 800°–1500°F during welding, the chromium in the steel combines with the carbon to form chrome carbides which tend to form along the grain boundaries of the metal (carbide precipitation). This lowers the dissolved chromium content in these areas and thus lowers their corrosion resistance, making them vulnerable to intergranular corrosion. Carbide precipitation is reduced by holding the carbon content of the material to a very low value. This limits the amount of carbon available to combine with the chromium. The “L” series (extra low carbon) stainless steels are often used for this purpose, but their use reduces system design stress by approximately 15%. Parker Weld-lok fittings are made from a select 316 series with carbon content in the low range of 0.04 to 0.07 percent. This results in a welded fitting with good corrosion resistance and a high strength factor. All Parker Weld-lok fittings in stainless steel are supplied in the solution treated condition, capable of passing ASTM-A-262 Tests for Detecting Susceptibility to Intergranular Corrosion.

Tacking
If the weld joint is to be “tacked” before welding, it is recommended that the “Tack” weld build-up be held to a minimum. Excessive build-up on the “tack” may cause an interrupted final bead and a stress riser or lack of complete fusion.

Backing Gas
Backing gas is an inert gas used to flood the interior of the fittings and tube system during welding. It serves the same purpose internally as the shielding gas used in TIG or MIG welding. By reducing the interior oxygen level to as low as practicable, it also serves to control the combustion of contaminates that could affect weld quality. When a backing gas is not used and nearly 100% weld penetration is achieved, blisters will tend to form on the internal tube wall. This will result in scale which may later break loose. Therefore, in 0.050 wall or thinner tube or where the wall thickness is such that the selected weld process may burn through, the use of a backing gas is mandatory. In most cases the backing gas will be argon or helium connected to the system through a control regulator. Flow rates, while small, should be high enough to purge the system. Welds should be made in downstream sequence from the gas connection. Note that the entire system should be purged to insure that there are no openings that will allow air to be drawn into the system. The use of backing gas, while often not mandatory, will give a better weld joint. This is because the effects of contaminate combustion by-products are eliminated and because the welds are made and cooled under a shielded atmosphere, thus eliminating internal scaling or blistering.

Arc Polarity
When welding Weld-lok fittings, best results will be obtained by the following arc polarities: TIG – Direct Current, straight polarity MIG – Direct Current, reverse polarity STICK – Polarity dependent on rod used For further information on Parker’s Welded Fittings refer to Parker’s Welded Fittings Catalog 4280 or contact Parker’s Instrumentation Connectors Division – Product Engineering at 256-881-2040.

57
Parker Hannifin Corporation

Tube to Welded Systems ZELW
Socket Weld Elbow
For fractional tube
for A-LOK to tubing socket weld connection
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. C L H P

*

X

W HEX

2-2 ZELW 3-3 ZELW 4-4 ZELW 6-6 ZELW 8-8 ZELW 10-10 ZELW 12-12 ZELW 16-16 ZELW

200-9-2 W 300-9-3 W 400-9-4 W 600-9-6 W 810-9-8 W 1010-9-10 W 1210-9-12 W 1610-9-16 W

1/8 3/16 1/4 3/8 1/2 5/8 3/4 1

.92 .98 1.07 1.26 1.37 1.56 1.56 1.94

.66 .72 .78 .97 .97 1.16 1.16 1.45

.63 .69 .78 .91 1.03 1.16 1.31 1.47

.16 .20 .25 .34 .41 .49 .50 .56

.38 .44 .50 .63 .76 .94 1.09 1.38

5/16 7/16 9/16 3/4 3/4 1-1/16 1-1/16 1-5/16

NOTE: C dimension is typical finger-tight.

Dimensions for reference only, subject to change.

*Socket Depth

C L W HEX

H

*P
X

ZELW2
Buttweld Elbow
For fractional pipe
for A-LOK to pipe buttweld connection

C L W HEX

H R X INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. BUTTWELD PIPE SIZE X BUTTWELD O.D. W HEX

C

H

L

R

2-1/8 ZELW2 3-1/8 ZELW2 4-1/8 ZELW2 4-1/4 ZELW2 6-1/4 ZELW2 8-3/8 ZELW2 8-1/2 ZELW2 10-1/2 ZELW2 12-3/4 ZELW2 16-3/4 ZELW2 16-1 ZELW2

200-2-2 W 300-2-2 W 400-2-2 W 400-2-4 W 600-2-4 W 810-2-6 W 810-2-8 W 1010-2-8 W 1210-2-12 W 1610-2-12 W 1610-2-16 W

1/8 3/16 1/4 1/4 3/8 1/2 1/2 5/8 3/4 1 1

1/8 1/8 1/8 1/4 1/4 3/8 1/2 1/2 3/4 3/4 1

.92 1.01 1.06 1.07 1.20 1.37 1.43 1.43 1.56 1.94 1.94

.72 .74 .74 .94 1.01 1.13 1.31 1.31 1.50 1.65 1.84

.66 .74 .77 .78 .91 .97 1.03 1.03 1.16 1.45 1.45

.34 .38 .38 .56 .56 .56 .75 .75 .75 .75 .94

.405 .405 .405 .540 .540 .675 .840 .840 1.050 1.050 1.315

7/16 1/2 1/2 9/16 5/8 3/4 7/8 7/8 1-1/16 1-3/8 1-3/8

NOTE: C dimension is typical finger-tight. Pipe buttweld end will conform to Schedule 80 unless otherwise noted.

Dimensions for reference only, subject to change.

58
Parker Hannifin Corporation

Tube to Welded Systems ZHLW
Socket Weld Connector
For fractional tube
for A-LOK to tubing socket weld connection
C INCHES TUBE O.D. A C D P W HEX A D P

*
E X

PARKER PART NO.

INTERCHANGES WITH

*

X

E BORE

W HEX

2-2 ZHLW 3-3 ZHLW 4-4 ZHLW 6-6 ZHLW 8-8 ZHLW 10-10 ZHLW 12-12 ZHLW 16-16 ZHLW

200-6-2 W 300-6-3 W 400-6-4 W 600-6-6 W 810-6-8 W 1010-6-10 W 1210-6-12 W 1610-6-16 W

1/8 3/16 1/4 3/8 1/2 5/8 3/4 1

1.14 1.17 1.32 1.48 1.62 1.65 1.71 2.08

.60 .64 .70 .76 .87 .87 .87 1.05

.88 .91 1.03 1.19 1.22 1.25 1.31 1.59

.16 .20 .25 .34 .41 .47 .50 .56

.38 .42 .48 .61 .79 .92 1.11 1.36

.093 .125 .187 .281 .406 .500 .625 .875

7/16 7/16 1/2 5/8 13/16 15/16 1-1/8 1-3/8

NOTE: A and C dimensions are typical finger-tight. Socket Depth

Dimensions for reference only, subject to change.

*

ZHLW2
Buttweld Connector
For fractional pipe
for A-LOK to pipe buttweld connection
C INCHES PARKER PART NO. INTERCHANGES WITH TUBE O.D. BUTTWELD PIPE SIZE X BUTTWELD O.D.

A D R

X

W HEX

A

C

D

R

W HEX

2-1/8 ZHLW2 3-1/8 ZHLW2 4-1/8 ZHLW2 4-1/4 ZHLW2 5-1/8 ZHLW2 5-1/4-ZHLW2 6-1/4 ZHLW2 6-3/8 ZHLW2 6-1/2 ZHLW2 6-3/4 ZHLW2 8-3/8 ZHLW2 8-1/2 ZHLW2 8-3/4 ZHLW2 10-1/2 ZHLW2 12-3/4 ZHLW2 16-1 ZHLW2

200-1-2 W 300-1-2 W 400-1-2 W 400-1-4 W 500-1-2 W 500-1-4-W 600-1-4 W 600-1-6 W 600-1-8 W 600-1-12 W 810-1-6 W 810-1-8 W 810-1-12 W 1010-1-8 W 1210-1-12 W 1610-1-16 W

1/8 3/16 1/4 1/4 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 3/4 1

1/8 1/8 1/8 1/4 1/8 1/4 1/4 3/8 1/2 3/4 3/8 1/2 3/4 1/2 3/4 1

1.20 1.24 1.29 1.49 1.48 1.49 1.57 1.60 1.82 1.88 1.71 1.93 1.99 1.93 1.99 2.46

.60 .64 .70 .70 .73 .73 .76 .76 .76 .76 .87 .87 .87 .87 .87 1.05

.94 .97 1.00 1.20 1.22 1.23 1.28 1.31 1.53 1.59 1.31 1.53 1.59 1.53 1.59 1.97

.38 .38 .38 .56 .38 .56 .56 .56 .75 .75 .56 .75 .75 .75 .75 .94

.405 .405 .405 .540 .405 .540 .540 .675 .840 1.050 .675 .840 1.050 .840 1.050 1.310

7/16 7/16 1/2 9/16 1/2 9/16 5/8 3/4 7/8 1-1/8 13/16 7/8 1-1/8 15/16 1-1/8 1-3/8

NOTE: A and C dimensions are typical finger-tight. Pipe Buttweld end will conform to Schedule 80 unless otherwise noted.

Dimensions for reference only, subject to change.

59
Parker Hannifin Corporation

Tube to Welded Systems ZHLW2
Buttweld Connector
For metric pipe
for A-LOK to pipe buttweld connection
PARKER PART NO. INTERCHANGES WITH TUBE O.D. BUTTWELD PIPE N.B. A C MILLIMETERS E BORE W HEX

D

R

X

ZHLW2 3-1/8 ZHLW2 4-1/8 ZHLW2 6-1/8 ZHLW2 6-1/4 ZHLW2 8-1/8 ZHLW2 8-1/4 ZHLW2 8-1/2 ZHLW2 10-1/4 ZHLW2 10-3/8 ZHLW2 10-1/2

3MO-1-2W 4MO-1-2 6MO-1-2 6MO-1-4W 8MO-1-2 8MO-1-1/4 8MO-1-8 – 10MO-1-6 – – – 12MO-1-8W – –

3 4 6 6 8 8 8 10 10 10 12 12 12 16 18

1/8 1/8 1/8 1/4 1/8 1/4 1/2 1/4 3/8 1/2 1/4 3/8 1/2 1/2 1/2 1/2

29,7 30,7 32,9 37,7 34,2 38,7 44,8 40,9 40,1 45,7 43,4 43,4 48,2 48,2 49,0 50,5

15,3 16,1 17,7 17,7 18,6 18,6 18,6 19,5 19,5 19,5 22,0 22,0 22,0 22,0 22,0 22,0

23,1 24,1 25,4 30,2 26,7 31,2 37,3 33,3 32,5 38,1 33,3 33,3 38,1 38,9 38,9 40,4

9,7 9,7 9,7 14,2 9,7 14,2 19,1 14,2 14,2 19,1 14,2 14,2 19,1 19,1 19,1 19,1

10,3 10,3 10,3 13,7 10,3 13,7 21,3 13,7 17,2 21,3 13,7 17,2 21,3 21,3 21,3 21,3

2,4* 2,4* 4,8 4,8* 5,1 6,4 6,4* 7,1 7,9* 7,9* 7,1 9,5 9,5* 9.5* 12,7* 13,5

12,0 12,0 14,0 14,0 15,0 15,0 22,0 18,0 18,0 22,0 22,0 22,0 22,0 24,0 24,0 27,0

A D R

E X

ZHLW2 12-1/4 ZHLW2 12-3/8 ZHLW2 12-1/2 ZHLW2 15-1/2 ZHLW2 16-1/2 ZHLW2 18-1/2

C

W HEX

NOTE: *E dimension is minimum opening. Dimensions for reference only, subject to change. Fittings of this group may be back-drilled to larger I.D. at pipe end. A and C dimensions are typical finger-tight. Pipe Buttweld end will conform to Schedule 80 unless otherwise noted.

60
Parker Hannifin Corporation

Analytical Fittings
Conical angle allows dispersement of flow over more frit surface .03 Controlled internal volume 6.1 X 10–4 cc

FLOW
.020 I.D.

.060

90

Drop In Frit Design

Precision tolerance tube bore for frit alignment.

Frit contained in tube bore by tubing with proper fitting make up.

Drop in frit allows accessibility for micron changes and cleaning

15 Flow stream contacts entire frit surface eliminating unswept volume .05 Controlled internal volume 1.2 X 10–3 cc

FLOW
.0135 I.D. Lead in angle for frit positioning

.122

6

Press In Frit Design

Precision tolerance counter bore for frit assembly

Avoidance of entrapment areas by flush mounting frit in counterbore

Pressed in frit eliminates movement of frit under pressure or disassembly.

Parker Hannifin’s Instrumentation Connectors Division offers a full line of analytical tube fittings. These fittings range from elbows, tees, and male connectors to low dead volume unions and column end fittings. Parker incorporates various features in the column end fittings to effectively address various industry concerns. Peak symmetry for critical analysis Internal volume reduction As the observed media/substance migrates through the HPLC column, a “peak” or “band” is created that denotes the level of concentration. It is critical to maintain peak symmetry in order to get an accurate reading when processing the observed media/substance. Parker Hannifin, in the development of a line of column end fittings, has incorporated some key features that help to maintain this “peak symmetry” in HPLC columns. “Under most circumstances in liquid chromatography (LC), the flow through the tube is laminar, the so-called Poiseulle flow, and in this situation the velocity at all points is parallel to the tube axis.” Due to the importance of maintaining smooth laminar flow after injection of the sample into the HPLC column, Parker

incorporated a small conical angle on the fitting body internals. This conical angle helps to equally disperse the sample into the column tube. One of the key requirements of an effective column end fitting is not to delay or disturb the flow of the sample through the instrument (HPLC column). A second area to address is the minimizing of tube fitting internal “cavities”. A cavity is a short section of the flow path where the flow-channel diameter increases. It can occur where tubes are connected to each other (low dead volume connector) or to injectors, columns (column end fittings), and detectors. Large cavities can seriously degrade the resolution of any chromatogram, but they can be easily avoided through awareness of the geometric design details of the fittings and connecting parts manufactured by various companies. Parker Hannifin has incorporated those critical features in both a low dead volume union connector and the column end fitting bodies. First, the utilization of inverted 1/16" connections to greatly reduce internal volume or cavities.To eliminate any confusion or occurrence of incorrect effective tube make-up, the port depths (body bore dimensions) are identical by size throughout the entire Parker Hannifin instrumentation line. Second, Parker closely monitors the dimensions of the small through-hole utilized in these low dead volume connectors.

61
Parker Hannifin Corporation

Analytical Fittings Z2HLZ7
Column End Fitting – Low Internal Volume with Frit
For fractional tube
PARKER PART NO. T1 TUBE O.D. T2 TUBE O.D. A INCHES W HEX INTERNAL OPENING INTERNAL VOLUME

C

D

2-1 Z2HLZ7 4-1 Z2HLZ7 6-1 Z2HLZ7

1/8 1/4 3/8

1/16 1/16 1/16

1.25 1.35 1.43

.60 .70 .76

.78 .84 .92

7/16 1/2 5/8

.013 .013 .013

5.4 x 10-4cc 1.2 x 10-3cc 3.8 x 10-3cc

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

FRIT DESIGNATOR A C2 C1 * MICRON DASH NO. MICRON SIZE

HOW TO ORDER

T2 MACHINED END TUBE O.D.

T1 TURNED END TUBE O.D.

–1 –2 –3 –4

0.5 2 5 10

EXAMPLE: 4-1Z2HLZ7-2*-SS To order with 2 frit for 1/4" O.D. column

W HEX D

Features: Inverted 1/16" end substantially reduces internal volume Flow stream contacts entire frit surface reducing plugging and eliminating unswept volume Can be used as a low volume final filter

Z3HLZ7
Column End Fitting – Low Internal Volume
For fractional tube
PARKER PART NO. T1 TUBE O.D. T2 TUBE O.D. A

INCHES W HEX INTERNAL OPENING INTERNAL VOLUME

C

D

4-1 Z3HLZ7 6-1 Z3HLZ7 8-1 Z3HLZ7 16-1 Z3HLZ7

1/4 3/8 1/2 1

1/16 1/16 1/16 1/16

1.28 1.37 1.62 2.00

.70 .76 .87 1.05

.77 .86 1.00 1.31

1/2 5/8 13/16 1-3/8

.020 .020 .030 .030

6.1 x 10-4cc 8.1 x 10-4cc 2.8 x 10-3cc 2 x 10-2cc

NOTE: A and C dimensions are typical finger-tight. A C

Dimensions for reference only, subject to change.

T2 MACHINED END TUBE O.D.

T1 TURNED END TUBE O.D.

Features: Inverted 1/16" end substantially reduces internal volume Drop in frit for use with L.C.* columns or G.C.* columns Conical angle below frit directs flow over more frit surface Available for up to 1" columns *G.C. = Gas Chromatagraph L.C. = Liquid Chromatagraph

W HEX D

Di-Frit (drop in)

PARKER PART NO.

MICRON SIZE

COLUMN O.D.

PARKER PART NO.

MICRON SIZE

COLUMN O.D.

4DI FRIT-2MIC-SS 4DI FRIT-5MIC-SS Replaceable frit for preparatory column end fitting Z3HLZ7. Frits are available in 2, 5 and 10 micron sizes. 4DI FRIT-10MIC-SS 6DI FRIT-2MIC-SS 6DI FRIT-5MIC-SS 6DI FRIT-10MIC-SS

2 5 10 2 5 10

1/4" 1/4" 1/4" 3/8" 3/8" 3/8"

8DI FRIT-2MIC-SS 8DI FRIT-5MIC-SS 8DI FRIT-10MIC-SS 16DI FRIT-2MIC-SS 16DI FRIT-5MIC-SS 16DI FRIT-10MIC-SS

2 5 10 2 5 10

1/2" 1/2" 1/2" 1" 1" 1"

62
Parker Hannifin Corporation

Analytical Fittings ZHLZ7
Column End Fitting – Low Internal Volume (without Frit)
For fractional tube
PARKER PART NO. INTERCHANGES WITH T1 TUBE O.D. T2 TUBE O.D. A INCHES W HEX INTERNAL OPENING INTERNAL VOLUME

C

D

2-1 ZHLZ7 4-1 ZHLZ7 6-1 ZHLZ7

-200-6-1-FGC -400-6-1-FGC -600-6-1-FGC

1/8 1/4 3/8

1/16 1/16 1/16

1.16 1.24 1.35

.60 .70 .76

.70 .77 .86

7/16 1/2 5/8

.013 .013 .013

1.0 x 10-4cc 1.1 x 10-4cc 1.3 x 10-4cc

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

A C

Features: Inverted 1/16" end substantially No frit for use with G.C.* columns or L.C.* columns with screens Can be used as a low volume reducing union
T1 TURNED END TUBE O.D.

T2 MACHINED END TUBE O.D.

*G.C. = Gas Chromatagraph L.C. = Liquid Chromatagraph

W HEX D

Z2HLZ
Column End Fitting – with Frit
For fractional tube
T2 MACHINED END TUBE O.D.

A C2 C1 T1 TURNED END TUBE O.D. W HEX D INCHES

PARKER PART NO.

T1 TUBE O.D.

T2 TUBE O.D.

A

C1

C2

D

W HEX

INTERNAL OPENING

INTERNAL VOLUME

2-1 Z2HLZ 4-1 Z2HLZ 6-1 Z2HLZ

1/8 1/4 3/8

1/16 1/16 1/16

1.21 1.35 1.44

.60 .70 .76

.43 .43 .43

.81 .91 1.00

7/16 1/2 5/8

.020 .020 .020

2.1 x 10-3cc 1.8 x 10-3cc 5.4 x 10-3cc

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

FRIT DESIGNATOR * MICRON DASH NO. MICRON SIZE

HOW TO ORDER

–1 –2 –3 –4
NOTE: Size 1 not silver-plated.

0.5 2 5 10

EXAMPLE: 4-1Z2HLZ-2*-SS To order with 2 frit for 1/4" O.D. column

Features: Flow stream contacts entire frit surface reducing plugging and eliminating unswept volume Can be used as a low volume final filter with drop-in frit

63
Parker Hannifin Corporation

Analytical Fittings ZHLZ
Column End Fitting – (without Frit)
For fractional tube
T2 MACHINED END TUBE O.D. W HEX D INCHES PARKER PART NO. INTERCHANGES WITH T1 TUBE O.D. T2 TUBE O.D. W HEX INTERNAL OPENING INTERNAL VOLUME A C2 C1 T1 MACHIMED END TUBE O.D.

A

C1

C2

D

2-1 ZHLZ 4-1 ZHLZ 6-1 ZHLZ

200-6-1LV 400-6-1LV 600-6-1LV

1/8 1/4 3/8

1/16 1/16 1/16

1.21 1.35 1.44

.60 .70 .76

.43 .43 .43

.81 .91 1.00

7/16 1/2 5/8

.020 .020 .020

2.1 x 10-3cc 2.1 x 10-3cc 2.3 x 10-3cc

NOTE: A and C dimensions are typical finger-tight. Size 1 Nut is not silver plated

Dimensions for reference only, subject to change.

Z7HLZ7
Union Connector – Low Dead Volume
For fractional tube
T1 MACHINED END TUBE O.D.

A B D1 H D2 T2 MACHINED END TUBE O.D. G1 E W HEX G2 C

INCHES PARKER PART NO. INTERCHANGES WITH T1 TUBE O.D. T2 TUBE O.D. E INTERNAL OPENING W HEX INTERNAL VOLUME

A

B

C

D1

D2

G1

G2

H

1-1 Z7HLZ7 2-1 Z7HLZ7 2-2 Z7HLZ7
Average Value

IFO-6GC – –

1/16 1/8 1/8

1/16 1/16 1/8

1.26 1.53 1.81

.21 .31 .31

.21 .21 .31

.41 .56 .56

.41 .41 .56

.013 .013 .052

.25 .38 .38

.25 .25 .38

.84 1.02 1.19

1/4 7/16 7/16

8.7 x 10-5cc 8.7 x 10-5cc 9.7 x 10-2cc

Dimensions for reference only, subject to change.

64
Parker Hannifin Corporation

Analytical Fittings FLZ7
Male Connector – Low Dead Volume
For fractional tube
W HEX B INCHES PARKER PART NO. TUBE O.D. NPT PIPE THREAD W HEX INTERNAL OPENING INTERNAL VOLUME A R

A

B

R

1-1 FLZ7 1-2 FLZ7 1-4 FLZ7
Average Value

1/16 1/16 1/16

1/16 1/8 1/4

.75 .79 1.01

.55 .59 .81

.38 .38 .56

5/16 7/16 5/8

.013 .013 .013

3.1 x 10-4cc 4.4 x 10-4cc 8.8 x 10-4cc

Dimensions for reference only, subject to change.

ZHLS
Sanitary Flange Fitting
For fractional tube
T

H F G E D C A B I T D C G F

H

E

B I

A

INCHES PARKER PART NO. INTERCHANGES WITH TUBE OD SANITARY FLANGE E MIN. OPENING G HEX FLAT

A

B

C

D

F

H

I

4-8 ZHLS-SS 4-12 ZHLS-SS 4-16 ZHLS-SS 4-24 ZHLS-SS 6-8 ZHLS-SS 6-12 ZHLS-SS 6-16 ZHLS-SS 6-24 ZHLS-SS 8-8 ZHLS-SS 8-12 ZHLS-SS 8-16 ZHLS-SS 8-24 ZHLS-SS

SS-400-SC-8 SS-400-SC-12 SS-400-SC-16 SS-400-SC-24 SS-600-SC-8 SS-600-SC-12 SS-600-SC-16 SS-600-SC-24 SS-810-SC-8 SS-810-SC12 SS-810-SC-16 SS-810-SC-24

1/4 1/4 1/4 1/4 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2

1/2 3/4 1 1 1/2 1/2 3/4 1 1 1/2 1/2 3/4 1 1 1/2

1.57 1.57 1.57 1.57 1.63 1.63 1.63 1.63 1.74 1.74 1.74 1.74

.37 .62 .87 1.37 .37 .62 .87 1.37 .37 .62 .87 1.37

.70 .70 .70 .70 .76 .76 .76 .76 .90 .90 .90 .90

.60 .60 .60 .60 .66 .66 .66 .66 .86 .86 .86 .86

.19 .19 .19 .19 .28 .28 .28 .28 .37 .41 .41 .41

1.00 1.00 1.38 1.38 1.00 1.00 1.38 1.38 1.00 1.00 1.38 1.38

9/16 9/16 9/16 9/16 11/16 11/16 11/16 11/16 7/8 7/8 7/8 7/8

1.34 1.34 1.34 1.28 1.34 1.34 1.34 1.34 1.40 1.34 1.34 1.34

.98 .98 1.98 1.98 .98 .98 1.98 1.98 .98 .98 1.98 1.98

NOTE: A, C, and D dimensions are typical finger tight.

Dimensions for reference only, subject to change.

Sanitary flange fittings combine the reliability and versatility of Parker tube fittings with conventional sanitary flanges. The fittings permit direct downstream connections for hookups and sampling. Flange sizes are 1/2, 3/4, 1, and 1-1/2 in. Parker tube fitting ends are available in 1/4, 3/8, and 1/2 in. Parker tube fittings allow use of a variety of tubing materials including metal, hard plastic, and soft plastic. For a Thermocouple/“Bored-Thru” version of the above Sanitary Adapter fittings, add a “4” to the part number. Example: A 4-12 ZHLS-SS becomes a 4-12 ZH4LS-SS for a 3/4" Sanitary Flange with a 1/4" diameter bored through on the A-LOK fitting end.

65
Parker Hannifin Corporation

Barbed Fittings B2HF
Barbed Connector to Male Pipe
For fractional tube
PARKER PART NO. INTERCHANGES WITH T1 HOSE I.D. T2 MALE PIPE SIZE A INCHES E BORE W HEX

K

2-2 B2HF 2-4 B2HF 4-2 B2HF 4-4 B2HF 5-2 B2HF 5-4 B2HF 6-4 B2HF 6-6 B2HF

2-HC-1-2 2-HC-1-4 4-HC-1-2 4-HC-1-4 5-HC-1-2 5-HC-1-4 6-HC-1-4 6-HC-1-6 8-HC-1-6 8-HC-1-8 12-HC-1-12

1/8 1/8 1/4 1/4 5/16 5/16 3/8 3/8 1/2 1/2 3/4

1/8 1/4 1/8 1/4 1/8 1/4 1/4 3/8 3/8 1/2 3/4

1.00 1.22 1.41 1.59 1.50 1.69 1.72 1.72 1.81 2.00 2.13

.078 .078 .188 .188 .188 .250 .281 .297 .375 .375 .625

.41 .41 .75 .78 .88 .88 .88 .88 .94 .94 1.03

7/16 9/16 7/16 9/16 7/16 9/16 9/16 11/16 3/4 7/8 1-1/16

A K

8-6 B2HF 8-8 B2HF 12-12 B2HF

Dimensions for reference only, subject to change. E T1 TURNED HOSE END W HEX T2 MACHINED PIPE END

B2TU
Barbed Connector to Tube Adapter
For fractional tube
PARKER PART NO. INTERCHANGES WITH T1 HOSE I.D. T2 TUBE O.D. A

INCHES E BORE W HEX

H

K

2 B2TU2 4 B2TU4 4 B2TU4 6 B2TU6

2-HC-A-201 2-HC-A-401 4-HC-A-401 4-HC-A-601

1/8 1/8 1/4 1/4

1/8 1/4 1/4 3/8

1.16 1.26 1.64 1.75

.078 .078 .156 .156

.53 .64 .64 .72

.41 .41 .78 .78

5/16 3/8 3/8 7/16

Dimensions for reference only, subject to change. NOTE: Tube adapter end is designed for use with Parker fittings or valves. Simply insert the tube adapter end until it bottoms and tighten the Parker nut 3/4 turns for sizes 3 and below, for sizes 4 and above 1-1/4 turns from finger tight. Add -Z6 for assembly of nuts and ferrules on the tube stub end. A K H

E T1 TURNED HOSE END

T2 MACHINED END TUBE O.D.

W HEX

HCS
Hose Connector Sleeve
For fractional tube
PARKER PART NO. HOSE I.D. HOSE O.D.

INCHES L W HEX

HCS 2-4 HCS 4-6 HCS 4-7 HCS 4-8 HCS 4-9 HCS 5-7 HCS 6-8 HCS 6-9 HCS 8-11 HCS 12-16

1/8 1/4 1/4 1/4 1/4 5/16 3/8 3/8 1/2 3/4

1/4 3/8 7/16 1/2 9/16 7/16 1/2 9/16 11/16 1

.41 .78 .78 .78 .78 .88 .88 .88 .94 1.06

3/8 9/16 5/8 11/16 3/4 5/8 11/16 3/4 7/8 1-1/4

L

Dimensions for reference only, subject to change.

W HEX

66
Parker Hannifin Corporation

Components TIZ
Insert
For fractional tube
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. TUBE I.D. TUBE WALL

3 TIZ (.125) 4 TIZ (.125) 4 TIZ (.170) 4 TIZ (.188) 5 TIZ (.125) 5 TIZ (.188) 5 TIZ (.250) 6 TIZ (.188) 6 TIZ (.250) 8 TIZ (.250) 8 TIZ (.375) 10 TIZ (.375) 10 TIZ (.500) 12 TIZ (.500) 12 TIZ (.625) 16 TIZ (.750) 16 TIZ (.875)

305-2 405-2 405-170 405-3 505-2 505-3 505-4 605-3 605-4 815-4 815-6 1015-6 1015-8 1215-8 1215-10 1615-12 1615-14

3/16 1/4 1/4 1/4 5/16 5/16 5/16 3/8 3/8 1/2 1/2 5/8 5/8 3/4 3/4 1 1

.125 .125 .170 .188 .125 .188 .250 .188 .250 .250 .375 .375 .500 .500 .625 .750 .875

.031 .062 .040 .031 .094 .062 .031 .094 .062 .125 .062 .125 .062 .125 .062 .125 .062

Dimensions for reference only, subject to change. NOTE: The TIZ insert is designed to be used with soft plastic tubing. Tubing wall thickness and corresponding minimum I.D. flow paths are listed so the system designer can properly match the insert to the tubing. Example: 4 TIZ (.125) is used with tubing having a wall thickness of .062 and I.D. of .125.

TIZ
Insert
For metric tube
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. TUBE I.D. TUBE WALL

TIZ6(4) TIZ8(6) TIZ10(6) TIZ10(8) TIZ12(8) TIZ12(10) TIZ15(10)

6M5-4M 8M5-6M 10M5-6M 10M5-8M 12M5-8M 12M5-10M 15M5-10M

6 8 10 10 12 12 15

4 6 6 8 8 10 10

1,0 1,0 2,0 1,0 2,0 1,0 2,5

Dimensions for reference only, subject to change. NOTE: The TIZ insert is designed to be used with soft plastic tubing. Tubing wall thickness and corresponding minimum I.D. flow paths are listed so the system designer can properly match the insert to the tubing. Example: TIZ6(4) is used with tubing having a wall thickness of 1mm and I.D. of 4mm.

NU
Tube Nut
For fractional tube
PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. A W HEX

1NU1 2NU2 3NU3 4NU4 5NU5 6NU6 8NU8 10NU10 12NU12 14NU14 16NU16 20NU20 24NU24 32NU32

102-1 202-1 302-1 402-1 502-1 602-1 812-1 1012-1 1212-1 1412-1 1612-1 2012-1 2412-1 3212-1

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2

.31 .47 .47 .50 .53 .56 .69 .69 .69 .69 .81 1.25 1.50 2.062

5/16 7/16 1/2 9/16 5/8 11/16 7/8 1 1-1/8 1-1/4 1-1/2 1-7/8 2-1/4 3

A

W HEX

Dimensions for reference only, subject to change. NOTE: All size 20, 24 and 32 silver plated nuts should have a system compatible lube (Permatex Anti-seize – Parker Catalog 4290-INST) or equivalent applied to the fitting body threads and the inside back of nuts. This will minimize the effort required to assemble the fitting properly.

67
Parker Hannifin Corporation

Components NUM
Tube Nut
For metric tube
A PARKER PART NO. INTERCHANGES WITH MILLIMETERS UN THREAD TUBE O.D. A W HEX

NUM2 NUM3 NUM4 NUM6 NUM8 NUM10 NUM12 NUM14 NUM15 NUM16 NUM18 NUM20 NUM22 NUM25

2M2-1 3M2-1 4M2-1 6M2-1 8M2-1 10M2-1 12M2-1 14M2-1 15M2-1 16M2-1 18M2-1 20M2-1 22M2-1 25M2-1

2 3 4 6 8 10 12 14 15 16 18 20 22 25

5/16-20 5/16-20 3/8-20 7/16-20 1/2-20 5/8-20 3/4-20 7/8-20 7/8-20 7/8-20 1-20 1.1/8-20 1.1/8-20 1.5/16-20

11,9 11,9 11,9 12,7 13,5 15,1 17,5 17,5 17,5 17,5 17,5 17,5 17,5 20,6

12,0 12,0 12,0 14,0 16,0 19,0 22,0 25,0 25,0 25,0 30,0 32,0 32,0 38,0

W HEX

Dimensions for reference only, subject to change.

BZI
Inverted Tube Nut
For fractional tube
A PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. A W HEX

1 BZI 2 BZI

1F2-1GC 2F2-1GC

1/16 1/8

.39 .44

1/4 7/16

Dimensions for reference only, subject to change.

W HEX

BZP
Knurled Nut
For fractional tube
A

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. A

1 BZP 2 BZP 3 BZP 4 BZP 5 BZP 6 BZP 8 BZP 10 BZP

102-1K 202-1K 302-1K 402-1K 502-1K 812-1K 602-1K 1012-1K

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8

.32 .47 .47 .51 .54 .57 .69 .69

HOW TO ASSEMBLE BZP 1. Replace NU nut with BZP nut on Parker A-LOK fitting body. 2. Insert plastic tubing until it bottoms in fitting body. 3. Tighten finger tight. The knurled nut is designed for use with soft plastic tubing on low pressure applications where a finger tight assembly procedure is satisfactory. Example: Laboratory test hook-ups. Nylon or Teflon ferrules are frequently used instead of metal ferrules in this type of application.

Dimensions for reference only, subject to change.

68
Parker Hannifin Corporation

Components INCH FF
Front Ferrule
For fractional tube

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D.

BF
Back Ferrule
For fractional tube

PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D.

1FF1 2FF2 3FF3 4FF4 5FF5 6FF6 8FF8 10FF10 12FF12 14FF14 16FF16 20FF20 24FF24 32FF32

103-1 203-1 303-1 403-1 503-1 603-1 813-1 1013-1 1213-1 1413-1 1613-1 2013-1 2413-1 3213-1

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2

1BF1 2BF2 3BF3 4BF4 5BF5 6BF6 8BF8 10BF10 12BF12 14BF14 16BF16 20BF20 24BF24 32BF32

104-1 204-1 304-1 404-1 504-1 604-1 814-1 1014-1 1214-1 1414-1 1614-1 2014-1 2414-1 3214-1

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2

For stainless steel, sizes 4-32 are Suparcase ferrules.

METRIC FFM
Front Ferrule
For metric tube
PARKER PART NO. INTERCHANGES WITH MM TUBE O.D.

BFM
Back Ferrule
For metric tube

PARKER PART NO.

INTERCHANGES WITH

MM TUBE O.D.

FFM2 FFM3 FFM4 FFM6 FFM8 FFM10 FFM12 FFM14 FFM15 FFM16 FFM18 FFM20 FFM22 FFM25

2M3-1 3M3-1 4M3-1 6M3-1 8M3-1 10M3-1 12M3-1 14M3-1 15M3-1 16M3-1 18M3-1 20M3-1 22M3-1 25M3-1

2 3 4 6 8 10 12 14 15 16 18 20 22 25

BFM2 BFM3 BFM4 BFM6 BFM8 BFM10 BFM12 BFM14 BFM15 BFM16 BFM18 BFM20 BFM22 BFM25

2M4-1 3M4-1 4M4-1 6M4-1 8M4-1 10M4-1 12M4-1 14M4-1 15M4-1 16M4-1 18M4-1 20M4-1 22M4-1 25M4-1

2 3 4 6 8 10 12 14 15 16 18 20 22 25

For stainless steel, sizes 6mm–25mm are Suparcase ferrules.

Ferrule Holder
Package simplifies ordering, stocking, and assembling

PARKER PART NO. 1 HOLDER

T TUBE O.D. (INCHES)

PARKER PART NO. 1 HOLDER

T TUBE O.D. (MM)

2ALOK-*-SET 4ALOK-*-SET 6ALOK-*-SET 8ALOK-*-SET 12ALOK-*-SET 16ALOK-*-SET

1/8 1/4 3/8 1/2 3/4 1

6M ALOK-*-SET 8M ALOK-*-SET 12M ALOK-*-SET

6 8 12

The Parker ferrule holder offers a new convenience. The holder contains individual ferrule sets. Ferrule sets may be dispensed one at a time.

*Material designator – 316-SS, B-Brass, S-Steel

*Material designator – 316-SS, B-Brass, S-Steel

69
Parker Hannifin Corporation

Components BLP
Plug
For fractional tube
For plugging open ended A-LOK fitting ends
PARKER PART NO. INTERCHANGES WITH INCHES TUBE O.D. THREAD A W HEX HOW TO ASSEMBLE Wrench tighten only 1/4 turn from finger tight position. Assembly includes machined ferrule with lock ring.

1BLP1 2BLP2 3BLP3 4BLP4 5BLP5 6BLP6 8BLP8 10BLP10 12BLP12 14BLP14

100-P 200-P 300-P 400-P 500-P 600-P 810-P 1010-P 1210-P 1410-P 1610-P 2010-P 2410-P 3210-P

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2

10-32 5/16-20 3/8-20 7/16-20 1/2-20 9/16-20 3/4-20 7/8-20 1-20 1-1/8-20 1-5/16-20 1-5/8-20 1-15/16-20 2-5/8-20

.31 .47 .47 .50 .53 .56 .69 .69 .69 .69 .81 1.35 1.72 2.27

5/16 7/16 1/2 9/16 5/8 11/16 7/8 1 1-1/8 1-1/4 1-1/2 1-7/8 2-1/4 3

A

16BLP16 20BLP20 24BLP24 32BPL32

Dimensions for reference only, subject to change. W HEX

BLPM
Plug
For metric tube
For plugging open ended A-LOK fitting ends
PARKER PART NO.

INTERCHANGES WITH

MILLIMETERS TUBE O.D. THREAD A W HEX

BLPM2 BLPM3 BLPM4 BLPM6 BLPM8 BLPM10 BLPM12 BLPM14 BLPM15 BLPM16

2MO-P 3MO-P 4MO-P 6MO-P 8MO-P 10MO-P 12MO-P 14MO-P 15MO-P 16MO-P 18MO-P 20MO-P 22MO-P 25MO-P

2 3 4 6 8 10 12 14 15 16 18 20 22 25

5/16-20 5/16-20 3/8-20 7/16-20 1/2-20 5/8-20 3/4-20 7/8-20 7/8-20 7/8-20 1-20 1-1/8-20 1-1/8-20 1-5/16-20

11,9 11,9 11,9 12,7 13,5 15,1 17,5 17,5 17,5 17,5 17,5 17,5 17,5 20,6

12,0 12,0 12,0 14,0 16,0 19,0 22,0 25,0 25,0 25,0 30,0 32,0 32,0 38,0

HOW TO ASSEMBLE Wrench tighten only 1/4 turn from finger tight position. Assembly includes machined ferrule with lock ring.

A

BLPM18 BLPM20 BLPM22 BLPM25

Dimensions for reference only, subject to change. W HEX

BLEN
Cap
For fractional tube
For capping open ended tubing
PARKER PART NO.

INTERCHANGES WITH

INCHES TUBE O.D. A C W HEX

1BLEN1 2BLEN2 3BLEN3 4BLEN4 5BLEN5 6BLEN6 8BLEN8 10BLEN10 12BLEN12 14BLEN14

100-C 200-C 300-C 400-C 500-C 600-C 810-C 1010-C 1210-C 1410-C 1610-C 2010-C 2410-C 3210-C

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2

.56 .79 .84 .92 .96 1.01 1.15 1.18 1.25 1.31 1.52 2.09 2.53 3.41

.43 .60 .64 .70 .73 .76 .87 .87 .87 .87 1.05 1.52 1.77 2.47

5/16 7/16 7/16 1/2 9/16 5/8 13/16 15/16 1-1/16 1-3/16 1-3/8 1-3/4 2-1/8 2-3/4

A C

16BLEN16 20BLEN20 24BLEN24 32BLEN32

W HEX

Dimensions for reference only, subject to change. NOTE: For body only specify PNZ A and C dimensions are typical finger-tight.

70
Parker Hannifin Corporation

Components BLENM
Cap
For metric tube
For capping open ended tubing
PARKER PART NO. INTERCHANGES WITH MILLIMETERS TUBE O.D. A C W HEX

BLENM2 BLENM3 BLENM4 BLENM6 BLENM8 BLENM10 BLENM12 BLENM14 BLENM15 BLENM16

2MO-C 3MO-C 4MO-C 6MO-C 8MO-C 10MO-C 12MO-C 14MO-C 15MO-C 16MO-C 18MO-C 20MO-C 22MO-C 25MO-C

2 3 4 6 8 10 12 14 15 16 18 20 22 25

13,5 13,5 14,3 15,9 17,1 19,1 19,1 19,8 19,8 19,8 21,3 23,9 23,9 26,2

15,3 15,3 16,1 17,7 18,6 19,5 22,0 22,0 22,0 22,0 22,0 22,0 22,0 26,5

12,0 12,0 12,0 14,0 15,0 18,0 22,0 24,0 24,0 24,0 27,0 30,0 30,0 35,0

A C

BLENM18 BLENM20 BLENM22 BLENM25

NOTE: For body only specify PNZ. Dimensions for reference only, subject to change. A and C dimensions are typical finger-tight. W HEX

MDF
Vent Protector NPT Male Pipe Thread
For fractional tube
PARKER PART NO. INTERCHANGES WITH THREAD SIZE A

INCHES E MINIMUM OPENING W HEX FLAT

R

4 MDF-SS 6 MDF-SS 8 MDF-SS 12 MDF-SS 16 MDF-SS

MS-MD-4M MS-MD-6M MS-MD-8M MS-MD-12M MS-MD-16M

1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2

.81 .81 1.06 1.13 1.31

.56 .56 .75 .75 .95

.28 .41 .50 .63 .94

9/16 11/16 7/8 1-1/16 1-3/8

Dimensions for reference only, subject to change.

A R E

Parker Instrumentation vent protectors (mud dauber fittings) protect open ends of instruments, tubing, outlet vents, etc. The mesh wire screen prevents foreign bodies such as insects or debris from entering and clogging various systems and causing damage. pipe plug, bored-thru design 40 x 40 mesh, .010 diameter wire screen designed to vent female pipe, straights, elbows or tees.

W HEX

71
Parker Hannifin Corporation

Components SEALING WASHERS
Bonded Seals
Consists of an outer stainless steel ring with a Viton inner ring used to seal a male ISO parallel thread.
PART NO. “T” BSPP THREAD PRESSURE RATINGS FOR SEALING WASHERS D H THREAD SIZE PSI BAR

M30201-SS M30202-SS M30203-SS M30204-SS M30206-SS M30208-SS

1/8 1/4 3/8 1/2 3/4 1

.63 .81 .94 1.12 1.38 1.69

.08 .08 .08 .10 .10 .10

1/8 1/4 3/8 1/2 3/4 1

5300 5500 4400 4000 3700 2800

370 380 300 280 260 190

These seals are also available in steel with a Nitrile inner ring. Dimensions for reference only, subject to change. Simply replace Suffix SS with S
H T D

Copper Washers

For BSPP male thread sealing
PART NO. THREAD D d H

For BSPP female thread sealing
PART NO. THREAD D d H

M28329 M28330 M28331 M28332 M28334 M28336
H d D

1/8 1/4 3/8 1/2 3/4 1

.71 .87 .94 1.18 1.38 1.65

.39 .55 .67 .87 1.06 1.34

.09 .09 .09 .10 .09 .09

M25179 M25180 M25181 M25182 M25184 M25186

1/8 1/4 3/8 1/2 3/4 1

.322 .436 .574 .719 .935 1.178

.218 .312 .437 .562 .812 1

.062 .062 .062 .062 .062 .093

Used to provide a seal with male or female parallel ISO threads.
Dimensions for reference only, subject to change.

Please note the pressure ratings are based on taper threaded ends. The pressure rating for the BSPP ends are dependent on the type of sealing washer used.

72
Parker Hannifin Corporation

Components WLZ
Bulkhead Locknut
For fractional tube
A
PARKER PART NO. INTERCHANGES WITH INCHES A-LOK THREAD TUBE O.D. A W HEX

1 WLZ 2 WLZ 3 WLZ 4 WLZ 5 WLZ 6 WLZ 8 WLZ 10 WLZ 12 WLZ 14 WLZ

102-61 202-61 302-61 402-61 502-61 602-61 812-61 1012-61 1212-61 1412-61 1612-61

10-32 5/16-20 3/8-20 7/16-20 1/2-20 9/16-20 3/4-20 7/8-20 1"-20 1-1/8-20 1-5/16-20

1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1

.13 .19 .22 .22 .23 .25 .28 .31 .34 .38 .38

5/16 1/2 9/16 5/8 11/16 3/4 15/16 1-1/16 1-3/16 1-3/8 1-5/8

W HEX

16 WLZ

Dimensions for reference only, subject to change.

WLN
Bulkhead Locknut
For fractional tube
A
PARKER PART NO. SAE ADJ. STR. THREAD TUBE O.D.

INCHES A W HEX

4 WLN 6 WLN 8 WLN 12 WLN 16 WLN

7/16-20 9/16-18 3/4-16 1-1/16-12 1-5/16-12

1/4 3/8 1/2 3/4 1

.28 .27 .31 .41 .41

11/16 13/16 1 1-3/8 1-5/8

Dimensions for reference only, subject to change.

W HEX

BN
Bulkhead Locknut
For metric tube
A
PARKER PART NO. SAE ADJ. STR. THREAD TUBE O.D.

MILLIMETERS A W HEX

2BN2 3BN3 4BN4 5BN5 BNM10 8BN8 10BN10 12BN12 14BN14 16BN16

5/16-20 3/8-20 7/16-20 1/2-20 5/8-20 3/4-20 7/8-20 1-20 1-1/8-20 1-5/16-20

2&3 4 6 8 10 12 14, 15 & 16 18 20 & 22 25

4,8 5,6 5,6 5,6 6,4 7,1 7,9 8,6 9,7 9,7

13,0 14,0 16,0 17,0 21,0 24,0 27,0 30,0 33,0 41,0

W HEX

Dimensions for reference only, subject to change.

L5N
Accessory Locknut
For fractional tube
A
PARKER PART NO. STRAIGHT THREAD

INCHES A W HEX

2 L5N 3 L5N 4 L5N 5 L5N 6 L5N 8 L5N 10 L5N 12 L5N 14 L5N 16 L5N

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1-1/16-12 1-3/16-12 1-5/16-12

.22 .22 .28 .28 .28 .31 .36 .41 .41 .41

7/16 1/2 9/16 5/8 11/16 7/8 1 1-1/4 1-3/8 1-1/2

W HEX

Dimensions for reference only, subject to change. NOTE: For use with M2SC and M2TU fittings on pages 54 and 55.

73
Parker Hannifin Corporation

Engineering Report
Assembly and Remake Instructions
INCH SIZE 1 thru 3 (1/16" - 3/16") METRIC SIZE 2 thru 4 (2-4mm)

Only 3/4 turn from finger tight is necessary to seal and will result in additional remakes of the fitting INCH SIZE 4 thru 16 (1/4" - 1") METRIC SIZE 6 thru 25 (6-25mm)

1. Parker instrument tube fittings are sold completely assembled and ready for immediate use. Simply insert the tube as illustrated until it bottoms in the fitting body. (If the fitting is disassembled, note that the small tapered end of the ferrule(s) go into the fitting body.) 2. Tighten nut finger tight. Then tighten nut with wrench an additional 1-1/4 turns indicated below. Hold fitting body with a second wrench to prevent body from turning. It is helpful to mark the nut to facilitate counting the number of turns. For maximum number of remakes, mark the fitting and nut before disassembly. Before retightening, make sure the assembly has been inserted into the fitting until the ferrule seats in the fitting. Retighten the nut by hand. Rotate the nut with a wrench to the original position as indicated by the previous marks lining up. (A noticeable increase in mechanical resistance will be felt indicating the ferrule is being re-sprung into sealing position.) Only after several remakes will it become necessary to advance the nut slightly past the original position. This advance (indicated by B) need only be 10°-20° (less than 1/3 of a hex flat).

A 1-1/4 Turns from Finger Tight B

A

For Sizes above 16 (1"), the Parker ICD Hydraulic Presetting Tool or Rotary Wrench Tool should be used. Cat. 4290-INST. For additional information please contact your local authorized Parker Instrumentation distributor or call Parker Instrumentation Connectors Division and ask for Bulletin 4230-B10.

Gaugeability Instructions

1. From “finger tight” position, wrench 1-1/4 turns for 1/4" to 1" size fittings (6mm to 25mm) (1/16", 1/8", 3/16", 2mm 3mm and 4mm size tube fittings only wrench 3/4 turn from finger tight position). Hold fitting body hex with second wrench to prevent body from turning as you tighten. It is a good idea to mark the nut (scribe or ink) to help you count the turns.

2. Now select the proper size inspection gauge and try to place it, as shown, between the nut and the body hex. If gauge DOES NOT FIT AT ANY POINT between them, you have correctly tightened the nut. If you can slip the gauge into the space, the fitting is not properly made up, and you must repeat the assembly procedure.

For additional information please contact your local authorized Parker Instrumentation distributor or call Parker Instrumentation Connectors Division and ask for Bulletin 4230-B15.2.

74
Parker Hannifin Corporation

Thread and Tube End Size Chart (U.S.A.)
NPT Thread NPT Thread
1/16" 1/8" (1/8-27)

Straight Thread Straight Thread
5/16-24 7/16-20

Tubing O.D. Size

1/16" 1/8"

1/4" (1/4-18)

1/2-20

3/16" 1/4"

3/8" (3/8-18)

9/16-18

5/16"

3/8"
1/2" (1/2-14)

3/4-16

1/2"

3/4" (3/4-14)

5/8"
7/8-14

3/4"

1" (1"-11 1/2)

1-1/16-12

7/8"

American Standard American Standard Pipe Thread (NPT) Pipe Thread (NPT)

American Standard American Standard Unified Unified Thread (Straight) (Straight) 1"

60° thread angle Pitch measured in inches Truncation of root and crest are flat Taper angle 1°47'

60° thread angle Pitch measured in inches Truncation of root and crest are flat Diameter measured in inches

75
Parker Hannifin Corporation

Pipe and Tube End Size Chart (U.S.A.)
NPT Thread NPT Thread Tubing O.D. Size

1-1/4"

1-1/4"

1-1/2"

1-1/2"

2"

2"

76
Parker Hannifin Corporation

Thread and Tube End Size Chart (International)
BSPT Tapered Thread
1/8" (1/8-28)

BSPP Parallel Thread
1/8" (1/8-28)

Tubing O.D. Size

2mm 3mm 4mm 6mm 8mm 10mm

1/4" (1/4-19)

1/4" (1/4-19)

3/8" (3/8-19)

3/8" (3/8-19)

12mm 14mm

1/2" (1/2-14)

1/2" (1/2-14)

15mm

16mm
3/4" (3/4-14) 3/4" (3/4-14)

18mm

20mm
1" (1"-11) 1" (1"-11)

22mm
International Organization for Standards International Organization for Standards (ISO 7/1) (ISO 228/1) (ISO 7/1) (ISO 228/1)

25mm
55° thread angle Pitch measured in inches Truncation of root and crest are round Taper angle 1°47' 55° thread angle Pitch measured in inches Truncation of root and crest are round Diameter measured in inches

77
Parker Hannifin Corporation

Offer of Sale
The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized distributors are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiaries and its authorized distributors. This offer and its acceptance by any customer ("Buyer") shall be governed by all of the following Terms and Conditions. Buyer’s order for any such items, when communicated to Parker Hannifin Corporation, its subsidiary or an authorized distributor ("Seller") verbally or in writing, shall constitute acceptance of this offer. 1. Terms and Conditions of Sale: All descriptions, quotations, proposals, offers, acknowledgments, acceptances and sales of Seller’s products are subject to and shall be governed exclusively by the terms and conditions stated herein. Buyer’s acceptance of any offer to sell is limited to these terms and conditions. Any terms or conditions in addition to, or inconsistent with those stated herein, proposed by Buyer in any acceptance of an offer by Seller, are hereby objected to. No such additional, different or inconsistent terms and conditions shall become part of the contract between Buyer and Seller unless expressly accepted in writing by Seller. Seller’s acceptance of any offer to purchase by Buyer is expressly conditional upon Buyer’s assent to all the terms and conditions stated herein, including any terms in addition to, or inconsistent with those contained in Buyer’s offer, Acceptance of Seller’s products shall in all events constitute such assent. 2. Payment: Payment shall be made by Buyer net 30 days from the date of delivery of the items purchased hereunder. Amounts not timely paid shall bear interest at the maximum rate permitted by law for each month or portion thereof that the Buyer is late in making payment. Any claims by Buyer for omissions or shortages in a shipment shall be waived unless Seller receives notice thereof within 30 days after Buyer’s receipt of the shipment. 3. Delivery: Unless otherwise provided on the face hereof, delivery shall be made F.O.B. Seller’s plant. Regardless of the method of delivery, however, risk of loss shall pass to Buyer upon Seller’s delivery to a carrier. Any delivery dates shown are approximate only and Seller shall have no liability for any delays in delivery. 4. Warranty: Seller warrants that items sold hereunder shall be free from defects in material or workmanship. THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO ITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHER WARRANTY, GUARANTEE, OR REPRESENTATION OF ANY KIND WHATSOEVER. ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR PURPOSE, WHETHER EXPRESS, IMPLIED, OR ARISING BY OPERATION OF LAW, TRADE USAGE, OR COURSE OF DEALING ARE HEREBY DISCLAIMED. NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR PARTIALLY, TO BUYER’S DESIGNS OR SPECIFICATIONS. 5. Limitation Of Remedy: SELLER’S LIABILITY ARISING FROM OR IN ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACT SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE ITEMS SOLD, AT SELLER’S SOLE OPTION. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING FROM OR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR ITEMS SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACH OF CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TO WARN OR STRICT LIABILITY. 6. Changes, Reschedules and Cancellations: Buyer may request to modify the designs or specifications for the items sold hereunder as well as the quantities and delivery dates thereof, or may request to cancel all or part of this order, however, no such requested modification or cancellation shall become part of the contract between Buyer and Seller unless accepted by Seller in a written amendment to this Agreement. Acceptance of any such requested modification or cancellation shall be at Seller’s discretion, and shall be upon such terms and conditions as Seller may require. 7. Special Tooling: A tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired to manufacture items sold pursuant to this contract. Such special tooling shall be and remain Seller’s property notwithstanding payment of any charges by Buyer. In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in the manufacture of the items sold hereunder, even if such apparatus has been specially converted or adapted for such manufacture and not withstanding any charges paid by Buyer. Unless otherwise agreed, Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time. 8. Buyer’s Property: Any designs, tools, patterns, materials, drawings, confidential information or equipment furnished by Buyer or any other items which become Buyer’s property, may be considered obsolete and may be destroyed by Seller after two (2) consecutive years have elapsed without Buyer placing an order for the items which are manufactured using such property, Seller shall not be responsible for any loss or damage to such property while it is in Seller’s possession or control. 9. Taxes: Unless otherwise indicated on the face hereof, all prices and charges are exclusive of excise, sales, use, property, occupational or like taxes which may be imposed by any taxing authority upon the manufacture, sale or delivery of the items sold hereunder. If any such taxes must be paid by Seller or if Seller is liable for the collection of such tax, the amount thereof shall be in addition to the amounts for the items sold. Buyer agrees to pay all such taxes or to reimburse Seller therefore upon receipt of its invoice. If Buyer claims exemption from any sales, use or other tax imposed by any taxing authority, Buyer shall save Seller harmless from and against any such tax, together with any interest or penalties thereon which may be assessed if the items are held to be taxable. 10. Indemnity For Infringement of Intellectual Property Rights: Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this Part 10. Seller will defend and indemnify Buyer against allegations of infringement of U.S. Patents, U.S. Trademarks, copyrights, trade dress and trade secrets (hereinafter ‘Intellectual Property Rights’). Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an action brought against Buyer based on an allegation that an item sold pursuant to this contract infringes the Intellectual Property Rights of a third party. Seller’s obligation to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten (10) days after Buyer becomes aware of such allegations of infringement, and Seller having sole control over the defense of any allegations or actions including all negotiations for settlement or compromise. If an item sold hereunder is subject to a claim that it infringes the Intellectual Property Rights of a third party, Seller may, at its sole expense and option, procure for Buyer the right to continue using said item, replace or modify said item so as to make it noninfringing, or offer to accept return of said item and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information provided by Buyer, or directed to items delivered hereunder for which the designs are specified in whole or part by Buyer, or infringements resulting from the modification, combination or use in a system of any item sold hereunder. The foregoing provisions of this Part 10 shall constitute Seller’s sole and exclusive liability and Buyer’s sole and exclusive remedy for infringement of Intellectual Property Rights. If a claim is based on information provided by Buyer or if the design for an item delivered hereunder is specified in whole or in part by Buyer, Buyer shall defend and indemnify Seller for all costs, expenses or judgments resulting from any claim that such item infringes any patent, trademark, copyright, trade dress, trade secret or any similar right. 11. Force Majeure: Seller does not assume the risk of and shall not be liable for delay or failure to perform any of Seller’s obligations by reason of circumstances beyond the reasonable control of Seller (hereinafter ‘Events of Force Majeure’). Events of Force Majeure shall include without limitation, accidents, acts of God, strikes or labor disputes, acts, laws, rules or regulations of any government or government agency, fires, floods, delays or failures in delivery of carriers or suppliers, shortages of materials and any other cause beyond Seller’s control. 12. Entire Agreement/Governing Law: The terms and conditions set forth herein, together with any amendments, modifications and any different terms or conditions expressly accepted by Seller in writing, shall constitute the entire Agreement concerning the items sold, and there are no oral or other representations or agreements which pertain thereto. This Agreement shall be governed in all respects by the law of the State of Ohio. No actions arising out of the sale of the items sold hereunder or this Agreement may be brought by either party more than two (2) years after the cause of action accrues. 11/98-P

78
Parker Hannifin Corporation

Parker Hannifin Corporation 6035 Parkland Blvd. Cleveland, Ohio 44124-4141 Telephone: (216) 896-3000 Fax: (216) 896-4000 www.parker.com

Parker Hannifin Corporation

About Parker Hannifin Corporation Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 500 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that control motion in some 1,000 industrial and aerospace markets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic, and electromechanical motion-control solutions. Our Company has the largest distribution network in its field, with over 7,500 distributors serving nearly 400,000 customers worldwide.

Parker’s Charter To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve profitable growth through premier customer service. Product Information North American customers seeking product information, the location of a nearby distributor, or repair services will receive prompt attention by calling the Parker Product Information Center at our toll-free number: 1-800-C-PARKER (1-800-272-7537). In Europe, call 00800-C-PARKER-H (00800-2727-5374).

The Aerospace Group is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high-technology markets, while achieving growth through premier customer service.

The Climate & Industrial Controls Group designs, manufactures and markets system-control and fluid-handling components and systems to refrigeration, air-conditioning and industrial customers worldwide.

The Fluid Connectors Group designs, manufactures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems.

The Seal Group designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction.

The Hydraulics Group designs, produces and markets a full spectrum of hydraulic components and systems to builders and users of industrial and mobile machinery and equipment.

The Filtration Group designs, manufactures and markets quality filtration and clarification products, providing customers with the best value, quality, technical support, and global availability.

The Automation Group is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide.

The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical flow components for worldwide process instrumentation, ultra-high-purity, medical and analytical applications.

Parker Hannifin Corporation Instrumentation Connectors Division P.O. Box 400004-1504 Huntsville, AL 35815-1504 USA Phone: (256) 881-2040 Fax: (256) 881-5730 www.parker.com/ICD Parker Hannifin plc Instrumentation Products Division Riverside Road Pottington Business Park Barnstaple, Devon EX31 1NP England Phone: +44 (0)1271 313131 Fax: +44 (0)1271 373636 Email: ipd@parker.com www.parker.com/instrumentation
Catalog 4233, 10M, 10/99


相关文章:
一般卡套式接头的介绍和双卡套式接头的安装指导书
一般卡套式接头的介绍和双卡套式接头的安装指导书_机械/仪表_工程科技_专业资料。卡套接头卡套式管接头的介绍一.单卡套式卡套接头 单卡套式卡套管接头由三部分...
双卡套接头的结构设计、安装和工作原理
双卡套接头的结构设计、安装和工作原理双卡套管接头是由美国人佛瑞德 A.雷能在 1947 年发明的。对比于螺纹、扩孔、 单卡套等接头形式, 双卡套管接头是一种兼顾...
卡套式管接头介绍
(2)双卡套接头 卡套接头的概述 卡套式管接头有四部分组成:接头体、前卡套、后卡套、螺母。当卡套和螺母在钢管上 插入接头体后,旋紧螺母时,卡套前端外侧与...
详解卡套接头
没有统一的制造标准,如 CPI 接头,ONE-LOK 接头等...双卡套接头发布日期:[2010-3-28 7:14:30] 点击...(two ferrule tube fitting)是由美国人佛瑞德 A....
卡套式接头特点及安装指导
技术资料 ? 卡套接头特点: 卡套接头通过拧紧螺母将卡套收紧在接头的 24°锥面内,在卡套咬住钢 管的 同时形成有效的硬接触密封。卡套接头最大特点是安装...
双 卡 套 阀 门 及 管 件
通管接头 DW3P DW4P DW6P DW2P 双卡套三 通管接头 DW3P DW4P DW6P 双卡套四 通管接头 双卡套四 通管接头 DW2P DW3P DW4P DW6P DW2P 双卡套角 ...
系列卡套接头和TUBE管
系列卡套接头和 TUBE 管: 规格: 工作温度: 15 系列 TUBE 管连接: -325°F (-198℃) ~ 800°F (427℃) SAE/MS 螺纹连接: 0°F (-17.8℃) ~ 400...
卡套
(two ferrule tube fitting)是由美国人佛瑞德 A....卡套接头 双卡套接头安装的注意事项 双卡套接头与...没有统一的制造标准,如 CPI 接头,ONE-LOK 接头等...
管接头
铰接接头、堵头、过 渡接头等 双卡套接头的组成:前卡环、后卡环、螺母 材质常用的是不锈钢和铜 公制、美制和英制螺纹标准 NPT,PT,G 都是管螺纹. NPT 是 ...
最全安全交底
4页 免费 A-Lok双卡套接头 80页 1财富值如要投诉违规内容,请到百度文库投诉中心;如要提出功能问题或意见建议,请点击此处进行反馈。 ...
更多相关标签:
双法兰松套传力接头 | 双卡套接头 | 双卡套式管接头 | 双层套管接头 | 双卡套接头标准 | 双法兰松套伸缩接头 | 双卡套式接头 | 双卡套异径直通接头 |