当前位置:首页 >> 机械/仪表 >>

华硕UL80系列拆机流程图


Disassembly procedure

2
Disassembly Procedure
Please follow the information provided in this section to perform the complete disassembly procedure of the notebook. Be sur

e to use proper tools described before.

Chapter

A
? ? ? ? ? ? ? ? ?

SUS UL80 Series Notebook consists of various modules. This chapter describes the procedures for the complete notebook disassembly. In addition, in between procedures, the detailed disassembly procedure of individual modules will be provided for your service needs.

The disassembly procedure consists of the following steps: Battery Module Memory Module Hard Disk Module Optical Driver Module Keyboard Module Top Case Module LCD Module Mother Board Module Bottom Case Module

2-1

V1.0

Disassembly procedure

B A T T E R Y

Battery Module
The illustration below shows how to remove the battery module.
Remove Battery module

B A T T E R Y M O D U L E R E M O V A L

1. Unlock the lath 1, and unlock the lath 2 and then take the battery module away. 2

1

2-2

V1.0

Disassembly procedure

M E M O R Y M O D U L E

Memory Module
The UL80 Series Notebook does not have RAM onboard. There are two SO-DIMM sockets for installing SO-DIMM RAM.
Remove Memory module

M E M O R Y R E M O V A L

1. Remove 2 screws on the DDR door, and take away the DDR door.

2. Open the 2 latches aside which will pop the memory module up to an angle of 30?, then pull out the memory module in that angle.

3. Open the 2 latches aside which will pop the memory module up to an angle of 30?, then pull out the memory module in that angle.

BACK

2-3

V1.0

Disassembly procedure

H A R D

D I S K

Hard Disk Module
The illustrations below show how to remove the hard disk board module from the notebook.
Removing Hard Disk Module

M O D U L E

H A R D

D I S K

M O D U L E R E M O V A L

1. Remove 2 screws on the HDD door, and take it away.

2. Release the HDD module, and take it away.

3. Remove 2 screws on the left side of the HDD bracket, and then remove 2 on the right side.

2-4

V1.0

Disassembly procedure

4. Separate the HDD bracket from the HDD module.

BACK

O P T I C A L

D R I V E R

Optical driver module
The illustration of below shows how to remove the optical driver module.
Removing opitcal driver module

M O D U L E

O P T I C A L

D R I V E R

R E M O V A L

1. Remove 2 screws here.

2-5

V1.0

Disassembly procedure

2. Take away the optical diver module.

3. Remove 2 screws here to separate the ODD bracket from the ODD module.

4. Remove 2 screws here to separate the bracket-L from the ODD module.

BACK

2-6

V1.0

Disassembly procedure

K E Y B O A R D

Keyboard module
The illustration of below shows how to remove the keyboard.
Removing Keyboard

K / B

R E M O V A L

1. Push the 4 latches with a pair of tweezers or a single-slotted screwdriver and lift the keyboard plate up.

2. Lay the keyboard down over the Top case. *Do not remove the keyboard yet.

2-7

V1.0

Disassembly procedure

3. Tear 1 piece of tape, and then disconnect the FPC connector.

C A B L E R E M O V A L

Removing Keyboard Cable

1. Use a flexible connector tool to unlock the cable connector on both ends (no. 1). 2. Carefully pull out the keyboard cable (no. 2) with a pair of tweezers. Lock the connector (no. 3) again to avoid possible breakage.
2. Cable out 1. Unlock 1. Unlock

3. Lock

3. Lock

2-8

V1.0

Disassembly procedure

4. Remove keyboard plate from top case

BACK

T O P

C A S E

Top Case Module
The illustrations below show how to disassemble and remove the top case module of the notebook. The module contains the top case itself.
1. Tear 1 piece of tape, and remove the warranty void label.

M O D U L E

2-9

V1.0

Disassembly procedure

2. Remove 10 screws here, and disconnect the FFC EXP, TP FFC.

3. Remove 11 screws here.

4. Separate the top case module from the bottom case module.

2 - 10

V1.0

Disassembly procedure

5. Disconnect the TP FFC here, and take it away.

6. Tear 2 pieces of tape here, then disconnect the touchpad FFC, and take it away.

7. Remove 2 screws here, and take away the touchpad board.

2 - 11

V1.0

Disassembly procedure

8. Remove 4 screws and tear 1 piece of tape here, and then take away the top case bracket R.

9. Tear 1 piece of tape here.

10. Disconnect the FFC EXP, and take it away.

2 - 12

V1.0

Disassembly procedure

11. Remove 2 screws here, and take away the switch board.

12. Remove 3 screws here, and take away the top case bracket L

BACK

2 - 13

V1.0

Disassembly procedure

L C D

M O D U L E

LCD Module
The illustrations below show how to remove and disassemble the LCD module. The module contains LCD panel, Inverter board, LCD bezel, LCD back cover.

L C D

M O D U L E

Disassembling LCD Module

D I S A S S E M B L Y

1. Disconnect the LVDs cable.

2. Tear 2 pieces of tape here.

3. Disconnect the wireless antennas and the camera cable.

2 - 14

V1.0

Disassembly procedure

4. Remove 2 screws from the left hinge, and then remove 2 from the right one.

5. Separate the LCD module from the bottom case module.

6. Remove 6 rubber pads and 6 screws from LCD module.

2 - 15

V1.0

Disassembly procedure

7. Pry four edges of the front bezel and take the front bezel away.

8. Remove 2 screws on the left hinge, and then remove 2 on the right one.

2 - 16

V1.0

Disassembly procedure

9. Take away the left hinge, and then take away the right one.

10.Remove 4 screws here, and take away the LCD panel.

11.Tear 1 piece of tape here, and disconnect the LVDs cable.

2 - 17

V1.0

Disassembly procedure

12.Release 3 pieces of tape here.

13.Disconnect the CMOS cable, and release the MIC here.

14.Take away the COMS cable, and then take away the camera cable.

BACK

2 - 18

V1.0

Disassembly procedure

M O T H E R B O A R D M O D U L E

Mother Board Module
The illustrations below show how to remove and disassemble the motherboard module. 1. Remove 4 screws here, and disconnect the speaker, Bluetooth, FAN, and DC-IN cable.

2. Separate the motherboard module from the bottom case module.

2 - 19

V1.0

Disassembly procedure

3. Remove 6 screws here, and take away the thermal module.

4. Remove 2 screws here, and take away the wireless LAN module.

2 - 20

V1.0

Disassembly procedure

5. Remove 2 screws here, and then take away the IO R board.

6. Tear 1 piece of tape here.

7. Remove 2 screws here, and take away the IO L board.

BACK

2 - 21

V1.0

Disassembly procedure

B O T T O M

C A S E

Bottom Case Module
The illustrations below show how to remove and disassemble the Bottom case module. The module contains Bluetooth board, speaker cable.
Disassembling Bottom case Module

M O D U L E

B O T T O M C A S E D I S A S S E M B L Y

1. Remove 2 screws here, and then take away the FAN.

2. Remove 1 screw here, and take away the DC cable.

3. Tear 3 pieces of tape here, and take away the speaker module.

2 - 22

V1.0

Disassembly procedure

4. Take away the Bluetooth module, and disconnect the Bluetooth cable.

BACK

2 - 23

V1.0


相关文章:
更多相关标签: