当前位置:首页 >> 数学 >>

SN225-2


November 2011
No guarantee can be given in respect of this translation

Double anchor plates
In all cases the latest German-language version of this standard shall be take

n as authoritative

for threaded bolts of property class 5.6 according to SN 172
ICS 21.060 Dimensions in mm

SN 225-2
Supersedes SN 225-2 : 2009-04

Table of contents
1 2 3 4 5 6 7

Page

Scope .......................................................................................................................................................................... 1 Dimensions ................................................................................................................................................................ 1 Designation ................................................................................................................................................................ 3 Materials ..................................................................................................................................................................... 3 Execution.................................................................................................................................................................... 3 Identification .............................................................................................................................................................. 3 Installation example .................................................................................................................................................. 4

1

Scope

This standard applies preferably to concrete construction for steelworks and rolling-mill equipment of the SMS Siemag BA of SMS group. It specifies dimensions of double anchor plates. These anchor plates are designed for threaded bolts of property class 5.6 as in SN 172.

2

Dimensions

The illustration in figure 1 shows the schematic view of an anchor plate. The specified dimensions shall be adhered to. Table 1 shows the dimensions of the double anchor plates in the size range from 24 to 160.

Degree of accuracy: DIN EN ISO 9013 – 342

centering pipe DIN EN 10296-1

face-machine

plate DIN EN 10029 coating acc. to SN 200-7 - 3.3.1 after fixing of U-shaped retainer acc. to SN 173 on the site

lifting hole space for marking, see section 6

Fig. 1 - Double anchor plate

Number of pages: 5
Edited by:

SMS Siemag Standards Office

? SMS Siemag for SMS GmbH 2011 The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization are prohibited. Any violations will result in an obligation to pay damages. All rights reserved".

Page 2 SN 225-2: 2011-11
Table 1 - Dimensions of double anchor plates Centering pipe Weight of For threaded Shuttering Weight of anchor plate bolt acc. to sleeve acc. to shuttering acc. to a) b) Size K a b ? d1 d2 h w DIN EN 10296-1 + centering SN 172 DIN EN 10296-1 sleeve pipe Outside dia. Outside dia. Thread x wall thickness d1 x wall thickness kg/unit kg/m 100 7,94 24 125 20 180 28 500 8,65 M 24 160 9,64 60,3 x 2,6 88,9 x 2,6 6,15 130 13,85 30 160 25 210 35 600 15,09 M 30 200 16,74 150 21,73 36 170 240 40 700 23,45 M 36 30 20 220 25,69 30 160 27,62 42 210 270 48 800 29,80 M 42 76,1 x 2,6 114,3 x 2,6 7,16 240 31,86 170 37,76 210 41,06 48 35 300 54 1000 M 48 250 44,35 290 47,65 180 52,15 220 56,30 56 40 330 62 1100 M 56 260 60,44 300 64,59 200 81,73 250 88,99 64 50 370 70 1300 M 64 300 96,25 350 103,51 36 25 114,3 x 2,6 139,7 x 2,6 8,79 220 119,62 270 129,27 72 410 80 1400 M 72 320 138,93 400 154,38 60 M12x24/34 250 145,92 300 156,51 80 450 90 1600 M 80 360 169,23 450 188,31 290 215,30 340 229,04 90 70 500 100 1800 M 90 410 248,27 480 267,51 M16x33/44 40 30 139,7 x 2,6 168,3 x 2,9 11,8 320 331,57 390 358,77 100 90 550 110 2000 M 100 460 385,97 540 417,06 360 444,35 430 477,32 110 100 600 120 2200 M 110 520 519,71 600 557,39 M20x36/49 46 35 168,3 x 2,9 193,7 x 2,9 13,6 400 603,15 470 632,05 125 660 135 2500 M 125 570 689,04 660 740,33 110 460 778,43 560 843,19 140 750 150 M24x43/58 57 40 2800 M 140 670 914,43 780 985,66 193,7 x 2,9 219,1 x 3,2 17,0 500 1152,39 600 1239,14 160 130 850 170 M30x53/70 75 45 3200 M 160 720 1343,23 840 1447,32 a) The specified values are guidance values and shall be used with preference. b) See figure 2 Lifting hole M12 drilled through M10 drilled through

Page 3 SN 225-2: 2011-11

3

Designation
Double anchor plate SN 225-2 – 48 x 290 – 5.6

Example: designation of a double anchor plate, size 48 and threaded bolt distance k = 290 mm for threaded bolts of property class 5.6.

4

Material

Anchor plate, plate made of S355JR+N according to DIN EN 10025-2. Centering pipe made of E235+N according to DIN EN 10296-1.

5

Execution

Cut out by flame, deburred and welded, with continuous fillet weld according to ISO 2553. Rolling skin, annealing scale and rust shall be removed by blasting. Surfaces without marking shall be left without coating or preservation. Indoor storage is required to avoid new formation of rust.

6

Identification

In case of e.g. thread size M48 and threaded bolt distance k = 290, double anchor plates shall be provided with permanent marking 48 x 290 in the form of welding beads for bolts of property class 5.6. Example of identification:

SN 225 – 2 – 48 x 290 – 5.6

Page 4 SN 225-2: 2011-11

7

Installation example

The following illustration Fig. 2 shows an installation example of a double anchor plate.

washer SN 220 or SN 808 machine component

b)

shims and levelling packs
a)

grouting SN 201 shuttering sleeve seal SN 207-2 d)

foundation SN 201
f)

threaded bolt SN 172 shuttering sleeve DIN EN 10296-1
c)

centering pipe DIN EN 10296-1

g)

double anchor plates SN 225-2

U-shaped retainer according to SN 173

Fig. 2 - Installation of a double anchor plate

a)

b)
c)

d)

e) f) g)

Height of machine base plate. The dimensions of v are based on washer thicknesses as in SN 808 + 1 x nut height as in DIN EN ISO 4032 (DIN 934) + ? 1 x d1 for the application of hydraulic pretensioning units as in NH (SMS Standards Book), Part 5. The length of the shuttering sleeve shall be chosen such that the sleeve projects by 100 mm over the raw concrete and can be subsequently adapted. The dimensions of w are based on rounded values of 20 x d1 without taking into account the quality of the concrete, reinforcement etc. Dimension ü is a variable overmeasure. Dimension L results from v+n+g+w+a+s+m+ü. After alignment/levelling of the anchor plate in the reinforcement, the customer shall arrange for water-tight welding of the shuttering sleeve.

e)

Page 5 SN 225-2: 2011-11 Referenced technical standards, codes and regulations
DIN 934 DIN EN 10025-2 DIN EN 10029 DIN EN 10296-1 Hexagon nuts; Metric coarse and fine pitch thread (from M72) Hot rolled products of structural steels; Technical delivery conditions for non-alloy structural steels Hot rolled steel plate 3 mm thick or above; tolerances on dimension, shape and mass Welded circular steel tubes for mechanical and general engineering purposes; Technical delivery conditions; Non-alloy and alloy steel tubes Hexagon nuts, style 1; Product grades A and B (up to M64) Thermal cutting; Classification of thermal cuts Welded, brazed and soldered joints; Symbolic representation on drawings Threaded bolts U-shaped retainers for threaded bolts Manufacturing Instructions Execution of structures and foundations Shuttering sleeve seals for threaded bolts Round washers for prestressed, high-strength screw connections Permissible bolt loads

DIN EN ISO 4032 DIN EN ISO 9013 ISO 2553 SN 172 SN 173 SN 200 SN 201 SN 207-2 SN 808 NH*, Part 5

*NH is the SMS book of standards (Standards Book / Design)

Revision of November 2011
Validity for SMS group (new logo). Figure 2 completed. Footnote of figure 2 revised. Table of contents added.


相关文章:
国内外常用钢号对照表
225M36 SCMnH11 220M07 SUM12 SUM22 SUM32 SUM42 45MF2 Z120M12 20F2 10...SNC81 5(H) 6 - 640A35 16NiCr 11 38CrNi Mo4(KB ) 20NiCr Mo2 40...
常用金属牌号及硬度_图文
.2~0.4 Sn7.0~9.0 Mn4.5~5.5 / / Al 0.5~1.5 Sn1.0~1.5 Sn...HRC 20--67,相当于 HB225--650 若硬度高于此范围则用洛式硬度 A 标尺 HRA...
接插件技术规范
225 汽车发动机冷却液安全使用技术条件 QC/T 417.1...2 电压降 扁形插塞式连接 Cu Zn,Cu Sn 初始 ...
北京人事任免
公司党委书记、董事长职务 东嘉生 不再担任北京王府井百货(集团)股份有限公司总经理职务 康典 不再担任新华人寿保险股份有限公司党委书记职务 责任编辑:陈琰 SN225 ...
2-焊锡准则
Sn 63 60 50 化 JIS 等级 63/37 60/40 55/45 50/50 Sn 62~64 59~...(34)焊锡处理时间(3~4 秒),温度 225℃±5℃确实实施。 8 (33)助焊剂涂布...
二组分金属相图
二组分金属相图一、实验目的 1、用热分析法(步冷曲线法)侧相变点,绘制 Sn-...225.7 226.5 227.6 227.6 226.7 225.0 222.5 219.8 246.7 249.2 ...
Sn-Bi二组分固液相图的绘制
Sn-Bi 二组分固液相图的绘制【实验目的】 1. 掌握热分析法绘制二组分固液...239.2 231.6 225.2 219 213 207 201.5 195.2 193.1 192.3 190.9 ...
2--数列和等差
一、选择题(每小题 5 分,共 30 分) 1.若数列{an}的前 n 项和 Sn=n2...1=139, ∴数列{|an|}的前 20 项的和 T20=S20-2S7=139-2×(-43)=225...
SN2.20、室内排水管道通球试验记录 SN3
SN2.20、室内排水管道通球试验记录 SN3_农学_农林牧渔_专业资料。室外雨污水管道...225 21 系统编号 6#、12#楼南侧雨水管 6#、12#楼南侧污水管 1#、6#楼...
信息论第二章答案
log52!? 225.581 bit (2) 52 张牌共有 4 种花色、13 种点数,抽取 13 张点数不同的牌的概率如下: (a)p(xi)=52/52 * 48/51 * 44/50 * 40/49...
更多相关标签:
陈琰 sn225 | 111.207.225.149 mh2 | kis 2 225 | mu2252 | kis 2 225.exe | 2r11b225ase | ids 2vs225 f837 | 183.2.225.218 |