当前位置:首页 >> 能源/化工 >>

KPIC


I. PRODUCT AND COMPANY IDENTIFICATION
Product Name or Number : YUHWA POLYPRO HJ4012 Manufacturer's Name : Korea Petrochemical Ind.Co.,Ltd. Emergency Telephone No. : 052-278-8246 / Fa

csimile No. : 052-269-9295 Address : 178, Bukok-Dong, Nam-Ku, Ulsan, Korea Hazardous Materials Description(49 CFR 172.101) : None Proper Shipping Name : YUHWA POLYPRO Chemical Family : Propylene Homopolymer : [- CH(CH?)CH?-]n Formula

II. INGREDIENTS
COMPOSITION CAS No. Cont'(%) Polypropylene 9003-07-0 Approx' 100 TOXICITY DATA Acute Oral LD50 Not Available Acute Dermal LD50 Acute Inhalation LD50 Based on data available to KPIC, the components in this product are not hazardous under OSHA Hazard Communication (29 CFR 1910, 1200) OSHA REGULATED No

CARCINOGENICITY NTP Not Listed

IARC Not Listed

III. HEALTH INFORMATION
PRIMARY ROUTE OF ENTRY INHALATION The health effects below are based upon component health effects consistent with requirements under OSHA Hazard Communication (29 CFR 1910, 1200) Eye Contact : product fines can cause mechanical irritation. Skin Contact : product is unlikely to cause irritation. Inhalation : product fines may cause mechanical irritation. Ingestion : product is practically non-toxic. Signs and Symptoms : irritation as noted above. Aggravated Medical Conditions : preexisting eye and respiratory disorders may be aggravated by exposure to product fines.

Yoonam Bldg., 1-1, Ogin-dong, Chongno-ku, Seoul, Korea Homepage www.kpic.co.kr TEL 82-2-2122-1515 FAX 82-2-2122-1519 e-mail master@kpic.co.kr

IV. OCCUPATIONAL EXPOSURE LIMITS
No OSHA/PEL or ACGIH/TLV has been established.

V. EMERGENCY AND FIRST AID PROCEDURES
Eye Contact : flush eyes with water if irritation occurs. Skin Contact : if contact with molten product occurs. treat as for thermal burn. Inhalation : not ordinarily required. Ingestion : not ordinarily required. NFPA RATINGS(SCALE 0-4) : Health = 1 Fire = 1 Reactivity = 0

VI. SUPPLEMENTAL INFORMATION
None identified

VII. PHYSICAL DATA
Boiling point (oC) Specific gravity Solubility in water N.A 0.90?0.92 insoluble Melting point (oC) % Volatile by volume Evaluation rate (Butylacetate1) >165 N.A N.A Vapor pressure (mmHg) Vapor dencity N.A N.A

N.A = Not Applicable

APPEARANCE AND ODOR Solid essentially colorless and odorless pellet.

VIII. FIRE AND EXPLOSION HAZARDS
FLASH POINT AND METHOD USED N.A EXTINGUISHING MEDIA Use water fog, foam, dry chemical or CO2 SPECIAL FIRE FIGHTING PROCEDURES AND PRECAUTIONS Material will not burn unless preheated. Do not enter confined fire space without full bunker gear (helmet with face shield, bunker coats, gloves and rubber boots), including positive pressure NIOSH approved self-contained breathing apparatus. Cool fire exposed containers with water. UNUSUAL FIRE AND EXPLOSION HAZARDS Treat as a solid that can burn. Molded parts generally burn slowly with a low smoke density and flaming drips. Under certain conditions can burn with a high smoke density. FLAMMABLE LIMITS % VOLUME IN AIR LOWER UPPER N.A

Yoonam Bldg., 1-1, Ogin-dong, Chongno-ku, Seoul, Korea Homepage www.kpic.co.kr TEL 82-2-2122-1515 FAX 82-2-2122-1519 e-mail master@kpic.co.kr

IX. REACTIVITY
STABILITY □UNSTABLE ■STABLE CONDITIONS AND MATERIAL TO AVOID Strong oxidizing agents HAZARDOUS DECOMPOSITION PRODUCTS At processing temperature, some degree of thermal degradation will occur ; although highly dependent on temperature and environmental conditions, a variety of decomposition products may be present ranging from simple hydrocarbons(such as methane and propane) to toxic/irritating gases (carbon monoxide and dioxide, acrolein, acids, ketones, aldehydes) ; see SPECIAL PRECAUTIONS HAZARDOUS POLYMERIZATION □MAY OCCUR ■WILL NOT OCCUR

X. EMPLOYEE PROTECTION
RESPIRATORY PROTECTION Not ordinarily required. PROTECTIVE CLOTHING Not ordinarily required. ADDITIONAL PROTECTIVE MEASURES Adequate ventilation and/or engineering controls are required when product is heated in processing.

XI. ENVIRONMENTAL PROTECTION
SPILL OR LEAK PROCEDURES Shovel and sweep up or use industrial vacuum cleaner : avoid generating dust clouds : put into containers for reclaiming or disposal. WASTE DISPOSAL Place in an appropriate disposal facility in compliance with local regulations. ENVIRONMENTAL HAZARDS N.A

XII. SPECIAL PRECAUTIONS
Treat as a solid that can burn. Store away from oxidizing materials, in a cool. Dry place with adequate ventilation : bond and ground transpire equipment. Avoid vapors from heated products. Adequate ventilation and/or engineering controls must be employed in high temperature processing to prevent exposure to potentially toxic/irritating fumes.

Yoonam Bldg., 1-1, Ogin-dong, Chongno-ku, Seoul, Korea Homepage www.kpic.co.kr TEL 82-2-2122-1515 FAX 82-2-2122-1519 e-mail master@kpic.co.kr

XIII. TRANSPORTATION REQUIREMENTS
DEPARTMENT □ FLAMMABLE LIQUID □ FLAMMABLE SOLID OF TRANSPORTATION □ FLAMMABLE GAS CLASSIFICATION □ COMBUSTIBLE LIQUID D.O.T. PROPER SHIPPING NAME N.A OTHER REQUIREMENTS N.A □ POISON, CLASS A □ IRRITATING MATERIAL □ POISON, CLASS B □ NON FLAMMABLE GAS □ OXIDIZING MATERIAL ■ NOT HAZARDOUS BY □ CORROSIVE MATERIAL D.O.T REGULATIONS □ OTHER SPECIFY BELOW

XIV. OTHER REGULATORY CONTROLS
EPA, FDA, OSHA, USDA, CPSC, etc. N.A

(Remark) The information contained herein is based on data considered accurate.However, no warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the use thereof. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by abnormal use of the material even if reasonable safety procedures are followed. Furthermore, vendee assumes the risk in his use of the material.

Yoonam Bldg., 1-1, Ogin-dong, Chongno-ku, Seoul, Korea Homepage www.kpic.co.kr TEL 82-2-2122-1515 FAX 82-2-2122-1519 e-mail master@kpic.co.kr


相关文章:
高分子企业一览表
KPIC 大韩油化 KKPC 锦湖石化 KEP 韩国工塑 Samyang 三养集团 Honam 湖南石油化学 Kopla 科普拉 SH 新湖石化 韩国大林 韩国现代 Hyosung 韩国晓星 韩国裕元 ...
PP及PS产能、牌号汇总
巴塞尔 大韩 60 21 36 345.5 12.7 30 利安德巴塞尔 大韩油化 KPIC 湖南 HONAM Sabic 住友化学 三井化学 RP348N、RP344N、RP346R、HP500N 1088A、1088B、...
PE(聚乙烯)80级管道原料
KPIC KPIC SAMSUNG Hyundai 马来西亚 ETILINAS 给水、燃气 齐鲁/福联 8.75(21.6Kg) 0.944 P502(BL)(基料属于中密度)0.17 适合做管件 马来西亚 ETILINAS ...
高分子企业一览表
KPIC 大韩油化 KKPC 锦湖石化 - KEP 韩国工塑 Samyang 三养集团 Honam 湖南石油化学 Kopla 科普拉 SH 新湖石化 韩国大林 韩国现代 Hyosung 韩国晓星 韩国裕元 ...
工具的使用
并以‘-Kpic’取代‘-fpic’ ,在连接时使用‘cc -belf -G’ 。 Solaris 使用 SparcWorks 编译器 以‘-pic’取代‘-fpic’ ,并以‘ld -G’取代‘gcc -...
新版苯乙烯一周分析发展评述
印度 Haldia 石化因技术方面的问题关闭了其位于西孟加拉的联合装置,检修约两周; 韩国的 KPIC 将于四月关闭昂山芳烃装置进行 4 天的检修. 2.亚洲苯乙烯 CFR 中国...
高分子专业就业企业一览表
KPIC 大韩油化 KKPC 锦湖石化 KEP 韩国工塑 Samyang 三养集团 Honam 湖南石油化学 Kopla 科普拉 SH 新湖石化 韩国大林 韩国现代 Hyosung 韩国晓星 韩国裕元 ...
高分子专业期待的企业
KPIC 大韩油化 KKPC 锦湖 石化 KEP 韩国工塑 Samyang 三养集团 Honam 湖南石油化学 Kopla 科普拉 SH 新湖石化 韩国大林 韩国现代 Hyosung 韩国晓星 韩国裕元 ...
Solaris新手100问
A: CC=cc C++=CC +w .SUFFIXES:.cpp .cpp.o: $(C++) -g -c -Kpic $< liberrlog.so:ErrLog.o ld -o liberrlog.so -G ErrLog.o 14. Q: 在 ...
高分子就业企业表
KPIC 大韩油化 KKPC 锦湖石化 KEP 韩国工塑 Samyang 三养集团 Honam 湖南石油化学 Kopla 科普拉 SH 新湖石化 韩国大林 韩国现代 Hyosung 韩国晓星 韩国裕元 ...
更多相关标签:
韩国kpic | kpic corporation | hkpic | kpic10.dll | kpic10.dll 64位 | 金山游侠kpic10.dll | kpic10.dll 64位下载 | kpic10.dll放在哪 |