当前位置:首页 >> 信息与通信 >>

升压型LED恒流驱动器芯片XL6003


Datasheet

400KHz 42V 2A Switching Current Boost LED Constant Current Driver
Features
n n n n n n n n n n n n n
n

XL6003

General Description

/>The XL6003 regulator is fixed frequency PWM Boost (step-up) LED constant current driver, capable of driving Series 1W LED units with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could directly drive 6 Series 1W LED units at VIN>12V .

Wide 5V to 18V Input Voltage Range 0.22V FB adjustable LED drive current Directly drive 6 Series 1W LED at VIN>=12V Fixed 400KHz Switching Frequency Max. 2A Switching Current Capability Up to 92% efficiency Excellent line and load regulation EN PIN TTL shutdown capability & With PWM Dimming Function Internal Optimize Power MOSFET Built in Soft-Start Function Built in Frequency Compensation Built in Thermal Shutdown Function Built in Current Limit Function Available in SOP8 package

The PWM control circuit is able to adjust the duty ratio linearly from 0 to 95%. An enable function, an over current protection function is built inside. An internal compensation block is built in to minimize external component count.

Applications
n n n n LED Lighting Boost constant current driver Monitor LED Backlighting 7’ to 15’ LCD Panels

Figure1. Package Type of XL6003

Rev 1.4 1

www.junyi-ic.com

Datasheet

400KHz 42V 2A Switching Current Boost LED Constant Current Driver
Pin Configurations

XL6003

EN VIN FB NC

1 2 XL6003 3 4

8 7 6 5

GND GND SW SW

Figure2. Pin Configuration of XL6003 (Top View) Table 1 Pin Description Pin Number 1 2 3 4 5,6 7,8 Pin Name EN VIN FB NC SW GND Description Enable Pin. Drive EN pin low to turn off the device, drive it high to turn it on. Floating is default high. Supply Voltage Input Pin. XL6003 operates from a 5V to 18V DC voltage. Bypass Vin to GND with a suitably large capacitor to eliminate noise on the input. Feedback Pin (FB). The feedback threshold voltage is 0.22V. No Connected. Power Switch Output Pin (SW). Output is the switch node that supplies power to the output. Ground Pin.

Rev 1.4 2

www.junyi-ic.com

Datasheet

400KHz 42V 2A Switching Current Boost LED Constant Current Driver
Function Block

XL6003

Figure3. Function Block Diagram of XL6003

Typical Application Circuit

Figure4. XL6003 Typical Application Circuit

Rev 1.4 3

www.junyi-ic.com

Datasheet

400KHz 42V 2A Switching Current Boost LED Constant Current Driver
Ordering Information
Part Number Lead Free XL6003E1 XL6003TRE1 Marking ID Lead Free XL6003E1 XL6003E1

XL6003

Package

Temperature Range

Packing Type Tube Tape & Reel

XLSEMI Pb-free products, as designated with “E1” suffix in the par number, are RoHS compliant.

Absolute Maximum Ratings(Note1)
Parameter Input Voltage Feedback Pin Voltage EN Pin Voltage Output Switch Pin Voltage Power Dissipation Thermal Resistance (SOP8) (Junction to Ambient, No Heatsink, Free Air) Operating Junction Temperature Storage Temperature Lead Temperature (Soldering, 10 sec) ESD (HBM) Symbol Vin VFB VEN VOutput PD RJA TJ TSTG TLEAD Value -0.3 to 20 -0.3 to Vin -0.3 to Vin -0.3 to 42 Internally limited 100 -40 to 125 -65 to 150 260 >2000 Unit V V V V mW ?C/W ?C ?C ?C V

Note1: Stresses greater than those listed under Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

Rev 1.4 4

www.junyi-ic.com

Datasheet

400KHz 42V 2A Switching Current Boost LED Constant Current Driver
XL6003 Electrical Characteristics
Ta = 25℃;unless otherwise specified. Symbol Parameter Test Condition Min. Typ.

XL6003

Max.

Unit

System parameters test circuit figure4 VFB Efficiency Feedback Voltage Vin = 5V to 12V, Vout=24V Iload=100mA Vin=12V ,Vout=24V Iout=0.3A 209 220 92 231 mV %

?

Electrical Characteristics (DC Parameters)
Vin = 12V, GND=0V, Vin & GND parallel connect a 100uf/50V capacitor; Iout=100mA, Ta = 25℃; the others floating unless otherwise specified. Parameters Input operation voltage Shutdown Supply Current Quiescent Supply Current Oscillator Frequency Switch Current Limit Output Power NMOS Symbol Vin ISTBY Iq Fosc IL Rdson VFB =0 Vin=12V, ISW=2A High (Regulator ON) Low (Regulator OFF) VEN =2V (ON) VEN =0V (OFF) VFB=0V VEN=0V VEN =2V, VFB =Vin 320 Test Condition Min. 5 70 2.5 400 2 110 120 Typ. Max. 18 100 5 480 Unit V uA mA Khz A mohm

EN Pin Threshold EN Pin Input Leakage Current Max. Duty Cycle

VEN IH IL DMAX

1.4 0.8 3 3 90 10 10

V uA uA %

Rev 1.4 5

www.junyi-ic.com

Datasheet

400KHz 42V 2A Switching Current Boost LED Constant Current Driver
Schottky Diode Selection Table
Current Surface Through VR (The same as system maximum input voltage) Mount Hole 20V 30V 40V 50V 1N5817 1N5818 1N5819 √ √ √ 3A √ √ √ √ SR302 1N5820 MBR320 SK32 1N5821 MBR330 SK33 30WQ03 31DQ03 SR303 1N5822 MBR340 MBR350 SK34 31DQ04 SR304 SK35 31DQ05 SR305 30WQ04 30WQ05

XL6003

60V

1A

MBR360 SK36

SR306

Typical System Application for VIN=5V to driver 3 x 1W series LED units

L 22uh/2A

D1 SK34 COUT 47uf/35V SW 5,6 Series 3 1W LED FB

VIN

2 XL6003 3 7,8 1 GND EN

+5V CIN 47uf /16V

ON OFF

RS 350mA ILED=0.22/RS

Figure5. XL6003 System Parameters Test Circuit (5V ~ 3 x 1W LED)

Rev 1.4 6

www.junyi-ic.com

Datasheet

400KHz 42V 2A Switching Current Boost LED Constant Current Driver

XL6003

Typical System Application for VIN>=12V to driver 6 x 1W series LED units

Figure6. XL6003 System Parameters Test Circuit (12V ~ 6 x 1W LED)

Typical System Application for VIN>=12V to driver 6 series x 28 parallel White LED Array

Figure7. XL6003 System Parameters Test Circuit (12V ~ 6 x 28 White LED)

Rev 1.4 7

www.junyi-ic.com

Datasheet

400KHz 42V 2A Switching Current Boost LED Constant Current Driver
Typical System Application for SEPIC Buck-Boost LED Driver

XL6003

Figure8. XL6003 System Parameters Test Circuit (Buck-Boost LED Driver)

Typical System Application for VIN>=12V to driver 6 x 1W series LED units With Dimming Function

Figure9. XL6003 System Parameters Test Circuit (12V ~ 6 x 1W LED with Dimming Function)

Rev 1.4 8

www.junyi-ic.com

Datasheet

400KHz 42V 2A Switching Current Boost LED Constant Current Driver
Package Information
SOP8 Package Mechanical Dimensions

XL6003

Rev 1.4 9

www.junyi-ic.com


相关文章:
QX5305-led升压恒流驱动电路
QX5305 升压型大功率 LED 恒流驱动器 概述 QX5305是一款高效率、高精度的升压型大功率 LED 灯恒流驱动控制芯片。 QX5305内置高精度误差放大器, 固定关断时间控制...
用常见的DC-DC芯片做LED恒流驱动电路
用常见的DC-DC芯片LED恒流驱动电路_电子/电路_工程科技_专业资料。用常见的 ...2、升压 IC,以 CE9908 为例,接法如下: 原理大家想一想,接法也可以先串联...
升压型LED驱动芯片MXT7523
升压型 LED 驱动芯片 MXT7523 MXT7523 是一个电流模式,固定频率升压转换器与集成的 N-FET 来驱动多达 8?10 个 白光 LED 串联。该系列连接允许 LED 电流是...
各大LED驱动芯片大全
各大LED驱动芯片大全_信息与通信_工程科技_专业资料。不知道发过没?各大 LED ...大功率升压型LED恒流驱动... 9页 免费 LED驱动芯片 5页 免费 三通道大...
常见DCDC芯片的LED恒流驱动电路
基于常见 DCDC 芯片LED 恒流驱动电路设计时间:2011-01-25 13:54:00 来源:电源网 作者: 其实每款 DC/DC 的 IC(无论升压或降压)都能接成恒流的 LED 的...
LED降压恒流驱动IC
LED 降压恒流驱动 IC 大功率 LED 驱动 IC-TAC7135...规格书下载:TAC9918 LED 升压恒流驱动 IC TAC2301 ...光衰底) >HPL-H99XL3C0(9mm 长*9mm 宽*1.5mm...
降压/升压式LED恒流驱动
降压/升压LED 恒流驱动信息科技学院电子信息工程 林利强摘要:某些电子设备和家用电器并不需要使用输入与输出完全隔离的开关电源。例如, 直流电机的驱动电源,空调、...
LED升压、升降压的驱动恒流IC推荐一
LED升压、升降压的驱动恒流IC推荐一_电子/电路_工程科技_专业资料 暂无评价|0人阅读|0次下载|举报文档 LED升压、升降压的驱动恒流IC推荐一_电子/电路_工程科技_...
XL60XX,XL40XX,XLxxxx系列恒流恒压驱动IC归类参数
XL60XX,XL40XX,XLxxxx系列恒流恒压驱动IC归类参数_电子/电路_工程科技_专业...升压型 LED 恒流驱动器芯片产品型号 XL6001 XL6003 XL6004 XL6005 XL6006 ...
LED恒流驱动及恒流IC大盘点
恒流驱动电路驱动 LED 是较为理想的,但相对而言价格...LED 恒流 IC 芯片大盘点 韩国 LDT LD1016 16 位...可编程升压型 2 段恒流驱动 IC MAX1553/MAX1554 ...
更多相关标签:
升压恒流驱动芯片 | 升压恒流芯片 | led升压恒流芯片 | 升压恒流led驱动ic | 升压恒流ic | led升压恒流ic | 3r33 升压 恒流 | 升压恒流源 |