当前位置:首页 >> 机械/仪表 >>

插座力矩要求Connector Torque


Connector 7 mm Type-N 50 ohm
2

Coupling Torque (Ncm/in-lb) 135/12 135/12 135/12

Width Across Coupling Nut Wrench Flats 3/4" 3/4" 3/4" 5/16" 20 mm 5/16" 5/16" 20mm 5/16" 6 mm 5/16" no spec. N/A no spec. N/A 12 mm 12 mm no spec.

Agilent Torque Wrench # 8710-1766 8710-1766 8710-1766 8710-1765 8710-1764 8710-1765 8710-1765 8710-1764 8710-1765 8710-2079 8710-1582 -

Agilent Open Ended Wrench # & Size1 8710-1770 8710-1770 8710-1770 1/2" 9/16" 9/16"

Type-N 75 ohm
2

3.5 mm standard 3 3.5 mm NMD 4 2.92 mm standard 2.4 mm standard 3 2.4 mm NMD 4 1.85 mm 1.0 mm SMA 5 TNC BNC SMC SMB Type-F Type-FD Type 7-16 1

90/8 90/8 90/8 90/8 90/8 90/8 34/3 56/5 56/5 N/A 34-45/3-4 N/A 168/15 168/15 2500-3000/ 222-267

8710-1761 7 mm 8710-0510 5/16"(8 mm) 8710-1770 9/16" 08513-20014 Spanner Wr. 8710-1761 7 mm

8710-1761 7 mm 8710-0510 5/16"(8 mm) 8710-1770 1/2" 08513-20014 Spanner Wr. 8710-0510 5/16"(8 mm)

When mating two connectors it is important to keep the connectors from rotating relative to one another. On many connectors open-ended wrenches can be used on wrench flats on the outer bodies of the connector to help restrict rotation. This column lists the common wrench flat widths formany Agilent connector components, and wrench part numbers when available. There will be exceptions to this list, and connector components made by suppliers other than Agilent are unlikely to use the same wrench flat dimensions.

2 Type-N connectors can be tightened hand tight, but for better repeatability they should be torqued to 135 N-cm. 3 The 5/16" head of the 8710-0510 wrench will need to be ground thinner for some applications. 4 NMD connectors are rugged test port or cable connectors. 5 A 56 N-cm. torque wrench should be used to connect male SMA connectors to either 3.5-mm or 2.92-mm connectors. A 90 N-cm torque wrench should be used to connect male 3.5-mm or male 2.92-mm connectors to mating female connectors.



相关文章:
扭矩限制器_图文
在调整好想要的扭矩强度之后,把有槽的 螺纹孔对准,然后插入六角螺钉后用六角 扳手固定。 BRB REGOLAZIONE DEI LIMITATORI DI COPPIA TORQUE LIMITER REGOLATION ...
【不得不看!】RAD充电系列扭矩扳手用户手册_图文
运输位置 Figure 3 图 3 3.2 Operating the torque wrench 操作此充电扭矩...将电池组插入充电轴插座; 向后推直至接合。 使用前给电池充电。 只有一次充电...
1001 Torque (TRU公司玩具的扭力测试标准)
1001 Torque (TRU公司玩具的扭力测试标准)_机械/仪表_工程科技_专业资料。1001 Torque (TRU公司玩具的扭力测试标准)PACIFIC PLAYTHINGS A Division of TRU (HK) Lt...
电动螺丝刀扭力控制操作使用标准
不可直接使用,需实际量测其扭力值是否符合规定要求...锁螺丝的力矩合适,公司一般五金类机壳为 6~7.8...(Screw torque standard) 高硬度材质用扭力标准 较...
RAD家族又添新成员—RAD智能套筒
青岛锐奥德扭力工具有限公司是加拿大RAD Torque Systems 公司在中国设立的唯一子公司,是RAD品牌气动扭矩扳手,电动扭矩扳手,电子精控定扭扭矩扳手,电池充电扭矩扳手,...
力矩
物理学上指使物体转动的 (torque) [1] 力乘以到转轴的距离 。即:M=L×F。其中 L 是从转动轴到着力点的矢量, F 是矢量力;力矩也 是矢量。 力矩的量纲是...
推力杆装配单元扭矩设定
165 扭矩范围:30Nm~150Nm 二、工艺要求 推力杆在后桥总成上的装配扭矩(Trail ...Torque Turnoff Torque ST1 Threshold Torque Torque Low Limit Turnoff Torque ...
转矩相关词汇
absorbed torque 被吸收的扭矩, 测力计测出的扭矩 accelerating torque 加速转矩, 加速扭转 alternate torque 交变扭矩 axial torque 旋 ...
静态和动态扭矩
Static vs.DynamicTorque 静态和动态扭矩 Dynamic Torque 动态扭矩: Dynamic torque is the accepted Strategy for fastening in General Motors.This method is used...
基于非晶态合金压磁效应的磁电式非接触动态扭矩测量1
基于非晶态合金压磁效应的磁电式非接触动态扭矩测量...torque sensor;magnetoelectricity induction;measurement...而图 2 或图 3 所示的测量方式恰好满足上述要求。...
更多相关标签: