当前位置:首页 >> 能源/化工 >>

18650单电芯规格书


深 圳 宝 嘉 能 源 有 限 公 司
SHENZHEN BAOJIA BATTERY CO., LTD.

DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 1 of 8

Specification Approval Sheet (cylinder Cell) 产品规格确认书(圆柱电 产品

规格确认书(圆柱电池)

Model/型号: BJ18650P 型号: 型号 Capacity/容量: 1300mAh 容量: 容量 Voltage/电压: 3.7V 电压: 电压

( 批准( 制定 Prepared By) 审核 Checked By) 批准(Approved By) ( 孙良通 20102010-06-28

深 圳 宝 嘉 能 源 有 限 公 司
SHENZHEN BAOJIA BATTERY CO., LTD.

DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 2 of 8

1.0 基本特性 Basic performance
型号 Model 外壳材质 Can Material 标称容量
NominalCapacity, (0.2C5A)

2.0 外形图 figure

BJ18650P 镀镍钢 Nickel-plated steel
1300mAh 3.70V 4.20 V 2.80V 1C5A 10C5A(最大 15C5A) 20 C5A 18.5 mm 66mm 约 36g ≤16m (充电态) Ω 0.2C5A×7.5hrs 1 C5A×2.5hrs. 0℃~45℃ 32oF~113oF -20℃~60℃ -4oF~140oF -10℃~45℃ 14oF~113oF 2.1 结构图 Structure

额定电压 Nominal Voltage 充电截止电压 Max Charge Voltage 放电终止电压 Discharge Cut-off Voltage 最大充电电流 Max. Charge Current 标准持续放电流 Standard Discharge Current 最大瞬间放电电流 Max. Discharge Curent 电池最大直径(光壳) Max. Diameter 电池最大高度(光壳) Max. Height 电池重量 (Approx.) Weight (Approx.) 内阻(Max, at 1000Hz.) Cell Impedance 充电方法 Charge Method 标准 Standard 快速 Quick

充电 Charge 操 作 温 度 Operating Temperature 放电 Discharge 贮存 Storage

3.0 主要放电曲线 Mainly capability graph
BJ18650P-1300mAh 15C Discharge Cruve BJ18650P-1300mAh 1C Charge Cruve

BJ18650P-1300mAh 13C Cycle Life

BJ18650P-1300mAh -20℃ Discharge Cruve ℃

深 圳 宝 嘉 能 源 有 限 公 司
SHENZHEN BAOJIA BATTERY CO., LTD.

DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 3 of 8

4.0 电池性能 Characteristic
若没有特别说明, 电池在做各项试验前, 均需在 86KPa~106 KPa 大气压, 环境温度 20℃±5℃, 相对湿度为 45%~ 75%的条件下,以 0.2C5A 恒流放电至终止电压 2.8V,并在收到产品两周内进行以下试验.

Without special instructions, the following tests should be done under the condition of : temperature(20℃
±5℃), atmospheric pressure (86KPa~106 Kpa), relative humidity (45%~75%), and the tests should be done within two weeks after receiving the products. 一些术语的定义:the definitions of some nomenclatures of this specification 标准充电:在环境温度 20℃±5℃的条件下,以 0.2C5A 充电, 当电池端电压达到充电截止电压时, 改为恒压充电, 直到充电电流小于或等于 0.01C5A 后停止充电. standard Charge: Charge with current 0.2C5A to limit charge voltage under the condition of 20℃±5℃ surrounding t emperature, then change to charge with constant voltage till the current less than or equal to 0.01 C5A.

4.1 电化学性能 Electrical Characteristic 序号 NO. 项目 Item 标准 Standard 测试方法 Test Method 在 1 标准大气压,环境温度 20℃±5℃,相对湿度为 45%~75%的条件下,电池标准充电后(以下若没有特别 A)1C5A ≥1h 1 常温放电性能 Discharge Characteristics B ) 10C5A 5.4min C ) 15C5A 3.2min ≥ Standard charged under the condition of normal atmospheric pressure and the environmental temperature of 25℃± 5℃ and 45%~75%RH, then rest for 30min and discharge at1C5A,10C5A,10C5A to the discharge cut-off voltage respectively. Charge/discharge cycle can be conducted for 3 times before meeting the Standards(the same below) 放电时间≥ 2 常温荷电保持能力 Normal Storage 255min Discharge Time≥ 255min 循环 300 次后放 3 循环寿命 Cycle Life 电时间≥3.23min Discharge Time≥ 3.23min 电池标准充电后, 开路放置 28 天, 再以 0.2C5A 放电至终 止电压. Store for 28 days after standard charged, then discharge at 0.2C5A to the discharge cut-off voltage. 1C5A/13C5A 放电至终止电压,搁置 30min,以此模式 循环 300 次 Conduct 1C5A /13C5A cycle for 300 times and measure final capacity. ≥ 说明, 均在此条件下放置, 皆按此充电方式) 搁置 30min, , 分别以 1C5A,10C5A,15C5A 进行放电至终止电压,循环 三次,当有一次达到标准,即达到标准要求(下同) .

深 圳 宝 嘉 能 源 有 限 公 司
SHENZHEN BAOJIA BATTERY CO., LTD. 4.2 安全性能 Safety Characteristic 序号 NO.

DOC NO.: QR-WI-733-003-002/A 4 REV. : A PAGE: 4 of 8

项目 Item

标准 Standard

测试方法 Test Method

电池标准充电后, 3C5A 电流充电至 4.8V,然后转恒压充电 以 至截至电流 0.01C5A 时终止. 1 过充性能 Overcharge 不爆炸,不起火 No fire,No explosion Standard charge. Charge at 3 C5A to 4.8V, then change to charge with constant voltage till the current less than or equal to 0.01 C5A. Observe the variation of the battery's appearance

电池标准充电后, 1C5A 进行放电至终止电压, 以 然后用 10 的电阻将电池正负极相连,搁置 14 天. 2 过放性能 Over Discharge 不起火,不爆炸 No fire,No explosion Standard charged. Discharge at 1C5A to discharge cut-off voltage and then connect the positive and negative terminals with a resistor of 10 for 14 days.

电池标准充电后,置于防爆玻璃罩中直接短路其正负极(线 不爆炸,不起火 常温短路性能 3 Short Circuit at Room Temperature 最高温度<150℃ No fire No explosion Max.temperature<150 ℃ 路总电阻不大于 50m ) ,当电池温度下降到比峰值约低 10 ℃时试验结束.观察电池的温度及外观变化.Standard charged. Keep the battery into a ventilation cabinet and short-circuit the positive and negative terminals directly (general resistance shall be less than or equal to 50m ). Stop the test when the temperature falls to value 10 ℃ lower than the peak value. Observe the variation of the battery's appearance and temperature.

4

挤压测试 Crush

不着火不爆炸 No fire and no explosion

挤压测试前电池用 0.2C 充满电,搁置 24 小时.从径向挤压 压力达到 13KN. Charge at 0.2C,and then leave for 24hrs, The crushing was continued until a force of 3000 lb (13 kN)

深 圳 宝 嘉 能 源 有 限 公 司
SHENZHEN BAOJIA BATTERY CO., LTD.

DOC NO.: QR-WI-733-003-002/A 5 REV. : A PAGE: 5 of 8

电池标准充电后,放在平面上,并与热电偶相连,将一直径 为 15.8mm 的棒放在电池高度方向中间位置, 让重量 9.1kg 的 重物从 610mm 高度自由垂落至冲击台面. 5 重物冲击性能 Impact 不爆炸,不起火 No fire No explosion Standard charge. Keep the battery connected with a thermocouple and put it on a impaction platform, place a 15.8mm diameter bar across the center of the biggest surface, then let a 9.1kg heavy hammer self fall off to the platform from a height of 610mm. Observe the variation of the battery's appearance. 电池标准充电后,放置于热箱中,并与热电偶相连,温度以 (5 ℃±2 ℃) /min 的速率升至 130 ℃±2 ℃并保温 30Min.

6

热冲击安全性能 Hot Oven

不起火,不爆炸 No fire, No explosion

Standard charge. Keep the battery connected with a thermocouple and put it into a circulating air oven. Temperature is raised at a rate of 5 ℃±2 ℃ per minute to a temperature of 130℃±2 ℃ and remained for 30min at this temperature. Observe the variation of the battery's appearance.

4.3 环境适应性能 Environment Adaptation Performance
序号 NO. 项目 Item 标准 Standard 不着火,不爆炸 No fire no explosion 测试方法 Test Method 针刺测试前电池用 0.2C 充满电,搁置 24 小时.用 Ф4mm 钢针刺穿电池 Charge at 0.2C,and then leave for 24hrs,check battery before / after cut through battery with Ф4mm needle 电池标准充电后,置于温度为 40℃±2℃,相对 湿度为 90%的恒温恒湿箱中,搁置 48h 后,取 电池不起火,不爆炸 放电时间≥180min 2 恒定湿热性能 Static Humidity Discharge Time ≥180min No remarkable deformation No smoking\ explosion 出电池 20±5℃环境下搁置 2h.观察电池外观变 化.然后以 0.2C5A 放电至终止电压. Standard charge. Put the battery into a 40℃± 2℃ and 90% RH chamber for 48h, then get it

1

针刺性能 Needle

out and store it for 2h at room temperature. Observe the variation of the battery's appearance and then discharge at 0.2C5A to discharge cut-off voltage, measuring final capacity.

深 圳 宝 嘉 能 源 有 限 公 司
SHENZHEN BAOJIA BATTERY CO., LTD.

DOC NO.: QR-WI-733-003-002/A REV. 6 : A PAGE: 6 of 8

标准充电后,将电池样品由高度(最低点高度)为 1m 的 位置自由跌落到 18~20mm 的硬木板上,要求各面各 跌落一次.然后将电池以 0.2C5A 放电至终止电压,做 不起火,不爆炸 放电时间≥255min No smoking , No fire,No explosion Discharge time≥255min 0.2C5/0.2C5 循环达到要求停止, 充放电循环次数不高于 3次 Standard charge. Then let it self fall off from a height of 1.0m (the lowest height) to a smooth wooden surface. The self fall off should be conducted from every positive and negative direction. Then discharge at0.2C5A to discharge cut-off voltage. Conduct 0.2C5A /0.2C5A cycle for 3 times. 不同温度下 的 放电性能 4 High-low A)60 ℃时≥285min Temperature Discharge B)0 ℃时≥240min; C)-20 ℃时≥180min No fire\explosion A)60 ℃时≥285min B)0 ℃时≥240min; C)-20 ℃时≥180min 电池不爆炸,不起火. 电池标准充电后, 60±2℃条件下恒温搁置 2h, 0.2C5A 在 以 放电至终止电压,然后在室温条件下标准充电, 依次按 照 0±2℃/-20±2℃的顺序在相应的恒温条件下搁置 16h, 以 0.2C5A 放电至终止电压. Standard charge. Then store for 2h at 60±2℃ and discharge at 0.2C5A to discharge cut-off voltage. then standard charge at room temperature and store for 20h according to the order of 0±2 ℃/-20±2 ℃ and discharge at 0.2C5A measuring corresponding discharge capacity. 电池标准充电后,安装在振动台面上,按下面的 振动频率和对应的振幅调整好试验设备,X,Y,Z 三个 方向每个方向上从 10Hz~55Hz 循环扫频振动 30min, 扫频速率为 1oct/min:A)振动频率:10Hz~30Hz ;位 移幅值(单振幅) :0.38mm ;B)振动频率:30Hz~ 55Hz ;位移幅值(单振幅) :0.19mm. 电池外观无明显损伤,不 振动环境 适应性能 Vibration 漏液,不冒烟,不爆炸 No remarkable damage, No smoking , No explosion Standard charge. Measure initial status. Equip it to the vibration platform, adjust and prepare the test equipment according to following vibration frequency and relevant swing, doing frequency sweeping from X, Y, Z three directions, each from 10Hz to 55Hz for 30 minutes of recycling, rating of which is 1oct/min:A)vibration frequency:10Hz~30Hz ;Displacement breadth (single swing): 0.38mm ; B) vibration frequency: 30Hz ~ 55Hz ; Displacement breadth(single swing): 0.19mm. Measure final status after sweeping and Observe the variation of the battery's appearance.

3

跌落性能 Drop

5

深 圳 宝 嘉 能 源 有 限 公 司
SHENZHEN BAOJIA BATTERY CO., LTD. 5.0 保质期及产品责任 Warranty Period & Product Liability

DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 7 of 8

保质期是从出厂日期(喷码)开始起 12 个月; 深圳宝嘉能源有限公司对因没有按本规格书规定操作而导致的意外不 负责任. Warranty period of this product is 12 months from manufacturing code. Baojia Battery Corporation Limited is not responsible for the troubles caused by mishandling of the battery which is clearly against the instructions in this specification.

6.0 电池使用时警告事项及注意事项 Warnings and Cautions in Using the Battery 为防止电池可能发生泄漏,发热,爆炸,请注意以下预防措施: To prevent a possibility of the battery from leaking, heating or explosion please observe the following precautions: 严禁将电池浸入海水或水中,保存不用时,应放置于阴凉干燥的环境中. Do not immerse the battery in water or seawater, and keep the battery in a cool dry surrounding if it stands by. 禁止将电池在热高温源旁,如火,加热器等使用和留置 Not use or leave the battery near a heat source as fire or heater. 充电时请选用锂离子电池专用充电器. Use the battery charger specifically for that purpose when recharging. 严禁颠倒正负极使用电池 Do not reverse the position and negative terminals. 严禁将电池直接插入电源插座. Do not connect the battery to an electrical outlet. 禁止将电池丢于火或加热器中 Do not discard the battery in fire or a heater. 禁止用金属直接连接电池正负极短路. Do not short-circuit the battery by directly connecting the positive and negative terminals with metal objects. 禁止将电池与金属,如发夹,项链等一起运输或贮存 Do not transport or store the battery together with metal objects such as hairpins, necklaces, etc 禁止敲击或抛掷,踩踏电池等 Do not strike, trample or throw the battery.. 禁止直接焊接电池和用钉子或其它利器刺穿电池. Do not directly solder the battery and pierce the battery with a nail or other sharp objects. 禁止在高温下(炙热的阳光下或很热的汽车中)使用或放置电池,否则可能会引起电池过热,起火或功能失效, 寿命减短. Do not use or leave the battery at high temperature (for example, at strong direct sunlight or in a vehicle in extremely hot weather). Otherwise, it can overheat or fire or its performance will be degenerate and its service life will be decreased. 禁止在强静电和强磁场的地方使用,否则易破坏电池安全保护装置,带来不安全的隐患. Do not use the battery in a location where static electricity and magnetic field is great, otherwise, the safety devices may be damaged, causing hidden trouble of safety. 如果电池发生泄露,电解液进入眼睛,请不要揉擦,应用清水冲洗眼睛,并立即送医治疗,否则会伤害眼睛

深 圳 宝 嘉 能 源 有 限 公 司
SHENZHEN BAOJIA BATTERY CO., LTD.

DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 8 of 8

If the battery has leaked, and the electrolyte get into the eyes, do not rub the eyes, instead, rinse the eyes with clean water, and immediately seek medical attention. Otherwise, it may injure eyes. 如果电池发出异味,发热,变色,变形或使用,贮存,充电过程中出现任何异常,立即将电池从装置或充电器中移 离并停用 If the battery gives off an odor, generates heat, becomes discolored or deformed, or in any way appear abnormal during use, recharging or storage, immediately remove it from the device or battery charger and stop using it 如果电极弄脏,使用前应用干布抹净,否则可能会导致接触不良功能失效 In case the battery terminals are dirty, clean the terminals with a dry cloth before use. Otherwise performance may occur due to the poor connection with the instrument. 废弃之电池应用绝缘纸包住电极,以防起火,爆炸. Be aware discarded batteries may cause fire or explode, tape the battery terminals to insulate them.

相关文章:
18650(3600mah)规格书(标准书)
编号CQ150908001 V1.0 第 1 页/共 11 页 昌祺协能电子有限公司文件名称 产品规格书 版本 页码 18650ICR2P电池规格书客户名称: 客户技术确认: 客户签章: 产品...
18650-2400规格书
18650-2400规格书_信息与通信_工程科技_专业资料。深圳市源和辉煌能源有限公司 文件编号:PD-SPE-013 版次: A/0 页码: 1/6 产品规格书 电池类型: 圆柱型锂...
18650-2000电芯规格书_图文
18650-2000电芯规格书_工作计划_计划/解决方案_实用文档。德赛能源科技有限公司 承认书文件名称: 18650 圆柱型锂离子电芯 文件编号: D.DD.S –01-138 送交...
18650-2000电芯规格书
2℃的 环境温度下以 0.2It mA 恒流放电至终止电压 2.75V;4) 计算放出的容量 放电容量: ≥60%C5mAh 37 德赛能源科技有限公司 18650 锂离子电芯规格书 D....
18650-2000规格书
18650-2000规格书_医药卫生_专业资料。深圳市源和辉煌能源有限公司 文件编号:PD-SPE-011 版次: A/0 页码: 1/6 产品规格书 电池类型: 圆柱型锂离子电池 电池...
18650-2200规格书
18650-2200规格书_电子/电路_工程科技_专业资料。深圳市源和辉煌能源有限公司 文件编号:PD-SPE-012 版次: A/0 页码: 1/6 产品规格书 电池类型: 圆柱型锂...
18650-1200规格书_图文
18650-1200规格书_金融/投资_经管营销_专业资料。深圳市源和辉煌能源有限公司 文件编号:PD-SPE-007 版次: A/0 页码: 1/7 产品规格书 电池类型: 圆柱型锂...
18650-1500规格书
18650-1500规格书_信息与通信_工程科技_专业资料。深圳市源和辉煌能源有限公司 文件编号:PD-SPE-009 版次: A/0 页码: 1/6 产品规格书 电池类型: 圆柱型锂...
18650加板规格书_图文
1.0 规格书页码 3 深圳市德强电子有限公司 18650-2600mAh 产品规格书 1 范围本产品规格书适用于深 圳市德强电子有限公司 生产的 18650 聚合物锂离子电池。 需...
18650锂电池组技术规格书
18650电池组技术规格书_信息与通信_工程科技_专业资料 暂无评价|0人阅读|0次下载|举报文档 18650电池组技术规格书_信息与通信_工程科技_专业资料。3串6并 ...
更多相关标签:
lg 18650电芯规格书 | 三星18650电芯规格书 | 18650电芯规格 | 18650电芯 | 18650电芯厂 | 18650电芯厂家 | 18650电芯容量 | 18650电芯生产厂家 |