当前位置:首页 >> 电力/水利 >>

keithley2400数字源表说明书


Series 2400

SourceMeter SMU Instruments
?

Tightly coupled precision sourcing and measurement

? Five instruments in one (IV Source, IVR Measure) ? Seven m

odels: 20–100W DC, 1000W pulsed, 1100V to 1?V, 10A to 10pA ? Source and sink (4-quadrant) operation ? 0.012% basic measure accuracy with 6?-digit resolution ? 2-, 4-, and 6-wire remote V-source and measure sensing ? 1700 readings/second at 4? digits via GPIB ? Pass/Fail comparator for fast sorting/binning ? Available high speed sense lead contact check function ? Programmable DIO port for automation/handler/prober control (except Model 2401) ? Standard SCPI GPIB, RS-232 and Keithley Trigger Link interfaces ? Keithley LabTracer 2.0 I-V curve tracing application software (download)

Advantages of a Tightly Integrated Instrument By linking source and measurement circuitry in a single unit, these instruments offer a variety of advantages over systems configured with separate source and measurement instruments. For example, they minimize the time required for test station development, setup, and maintenance, while lowering the overall cost of system ownership. They simplify the test process itself by eliminating many of the complex synchronization and connection issues associated with using multiple instruments. And, their compact half-rack size conserves precious “real estate” in the test rack or?bench. Power of Five Instruments in One (IV Source, IVR Measure) The tightly coupled nature of a SourceMeter SMU instrument provides many advantages over solutions configured from separate instruments, such as a precision power supply and a digital multimeter. For example, it provides faster test times by reducing GPIB traffic and simplifies the remote programming interface. It also protects the device under test from damage due to accidental overloads, thermal runaway, etc. Both the current and voltage source are programmable with readback to help maximize device measurement integrity. If the readback reaches a programmed compliance limit, then the source is clamped at the limit, providing fault protection. ACCESSORIES AVAILABLE
TEST LEADS 1754 5804 5805 5808 5809 8607 CA-18-1 SWITCHING 7001 7002 7019-C 7053 AND PROBES 2-Wire Universal 10-Piece Test Lead Kit Kelvin (4-Wire) Universal 10-Piece Test Lead Kit Kelvin (4-Wire) Spring-Loaded Probes Low Cost Single-pin Kelvin Probe Set Low Cost Kelvin Clip Lead Set 2-Wire, 1000V?Banana Cables, 1m (3.3 ft) Shielded Dual Banana Cable, 1.2m (4 ft) HARDWARE Two-Slot Switch System Ten-Slot Switch System 6-Wire Ohms Switch Card High-Current Switch Card Communication Interface KPCI-488LPA IEEE-488 Interface/Controller for the PCI?Bus KUSB-488B IEEE-488 USB-to-GPIB?Interface Adapter Triggering and Control 2499-DIGIO Digital I/O?Expander Assembly (not for Model 2401) 8501-1 Trigger Link Cable, DIN-to-DIN, 1m (3.3 ft) 8501-2 Trigger Link Cable, DIN-to-DIN, 2m (6.6 ft) 8502 Trigger Link to BNC?Breakout Box 8503 Trigger Link Cable, DIN-to-Dual BNC, 1m (3.3 ft) 8505 Male to 2-Female Y-DIN?Cable for Trigger Link RACK MOUNT KITS 4288-1 Single Fixed Rack Mount Kit 4288-2 Dual Fixed Rack Mount Kit 4288-4 Dual Fixed Rack Mount Kit 4288-5 Shelf Type Side by Side Rack Mounting Kit 4288-9 Dual Fixed Rack Mounting Kit Software LabTracer 2.0 Curve Tracing Software (downloadable)

SMU INSTRUMENTS

CABLES/ADAPTERS 7007-1 Shielded GPIB Cable, 1m (3.3 ft) 7007-2 Shielded GPIB Cable, 2m (6.6 ft) 7009-5 RS-232 Cable 8620 Shorting Plug

是德仪器  www.shide17.com 咨询购买请联系 188 1070 9588  QQ: 625223001   王先生

A Greater Measure of Confidence

Tightly coupled precision sourcing and measurement

Keithley’s Series 2400 Source Measure Unit (SMU) Instruments are designed specifically for test applications that demand tightly coupled sourcing and measurement. All SourceMeter models provide precision voltage and current sourcing as well as measurement capabilities. Each SourceMeter SMU instrument is both a highly stable DC power source and a true instrument-grade 6?-digit multimeter. The power source characteristics include low noise, precision, and readback. The multimeter capabilities include high repeatability and low noise. The result is a compact, single-channel, DC parametric tester. In operation, these instruments can act as a voltage source, a current source, a voltage meter, a current meter, and an ohmmeter. Manufacturers of components and modules for the communications, semiconductor, computer, automotive, and medical industries will find the SourceMeter SMU instruments invaluable for a wide range of characterization and production test applications.

Series 2400

SourceMeter SMU Instruments
?

Ordering Information
200V, 1A, 20W SourceMeter SMU Instrument 2400-C 200V, 1A, 20W SourceMeter SMU Instrument with Contact Check 2401 20V, 1A, 20W SourceMeter SMU Instrument 2410 1100V, 1A, 20W SourceMeter SMU Instrument 2410-C 1100V, 1A, 20W SourceMeter SMU Instrument with Contact Check 2420 60V, 3A, 60W SourceMeter SMU Instrument 2420-C 60V, 3A, 60W SourceMeter SMU Instrument with Contact Check 2425 100V, 3A, 100W SourceMeter SMU Instrument 2425-C 100V, 3A, 100W SourceMeter SMU Instrument with Contact Check 2430 100V, 10A, 1000W Pulse?Mode SourceMeter SMU Instrument 2430-C 100V, 10A, 1000W Pulse?Mode SourceMeter SMU Instrument with Contact?Check 2440 40V, 5A, 50W SourceMeter SMU Instrument 2440-C 40V, 5A, 50W SourceMeter SMU Instrument with Contact Check Accessories Supplied Model 8605 Test Leads LabVIEW Software Driver ?(downloadable) LabTracer Software ?(downloadable) 2400

I-V?Characteristics All SourceMeter SMU instruments provide four-quadrant operation. In the first and third quadrants they o ? perate as a source, delivering power to a load. In the second and fourth quadrants they operate as a sink, d ? issipating power internally. Voltage, current, and resistance can be measured during source or sink ? operation.
Imeter Local Remote Isource DUT Vmeter/Compliance Remote Local SENSE LO IN/OUT LO Feedback to Adjust Vsource Remote Local SENSE LO IN/OUT LO IN/OUT HI SENSE HI Vsource Vmeter DUT Imeter/Compliance Local Remote IN/OUT HI SENSE HI

Tightly coupled precision sourcing and measurement

Source I–Measure V, I, or W configuration
Series 2400 SourceMeter SMU Instruments
+1A

Source V–Measure I, V, or W configuration

Model 2400 SourceMeter SMU Instrument

+100mA

Model 2401 Low-Voltage SourceMeter SMU Instrument
+20V +200V –200V –20V

+1A

+1 00m A

–200V

–20V

+20V

+200V

2400 only –100mA

2400 only

–100m A

Duty cycle limited
–1A –1A

Duty cycle limited

Model 2410 High-Voltage SourceMeter SMU Instrument

+1A +200mA

Model 2420 3A SourceMeter SMU Instrument

+3A +1A

Model 2425 100W SourceMeter SMU Instrument

+3A +1A

+20mA –1100V –200V –20V +20V +200V +1100V –60V –20V

+100mA +20V +60V –100V –60 –20

+100mA +20 +60 +100V

–20mA

–100mA

–100mA

–100mA –1A

–1A

–1A

Duty cycle limited

–3A

Duty cycle limited

–3A

Duty cycle limited

+1A +100mA

1A 100mA –40V –10V +10V –100mA –1A –1A –3A –10A +40V

–100V –60 –20

+20 +60 +100V

–100mA

Duty cycle limited Pulse mode only
–5A

–3A

Duty cycle limited

1.888.KEITHLEY (U.S. only) www.keithley.com
A Greater Measure of Confidence

SMU INSTRUMENTS

Model 2430 1kW Pulse Mode SourceMeter SMU Instrument

+10A +3A

Model 2440 5A SourceMeter SMU Instrument

5A

3A

Tightly coupled precision sourcing and measurement

Series 2400

SourceMeter SMU Instruments
?

Tightly coupled precision sourcing and measurement

Standard and Custom Sweeps Sweep solutions greatly accelerate testing with automation hooks. Three basic sweep waveforms are provided that can be programmed for singleevent or continuous operation. They are ideal for I/V, I/R, V/I, and V/R characterization. ? Linear Staircase Sweep: Moves from the start level to the stop level in equal linear steps ? Logarithmic Staircase Sweep: Done on a log scale with a specified number of steps per decade ? Custom Sweep: Allows construction of special sweeps by specifying the number of measurement points and the source level at each point ? Up to 1700 readings/second at 4? digits to the GPIB bus ? 5000 readings can be stored in the nonvolatile buffer memory

Stop

Start Bias Bias

Linear staircase sweep
Stop

Start Bias Bias

Logarithmic staircase sweep
Start User defined steps Stop

Built-In Test Sequencer Bias Bias (Source Memory List) The Source Memory list provides faster and Custom sweep easier testing by allowing you to setup and execute up to 100 different tests that run without PC intervention. ? Stores up to 100 instrument configurations, each containing source settings, measurement settings, pass/fail criteria, etc. ? ? Pass/fail limit test as fast as 500?s per point ? Onboard comparator eliminates the delay caused when sending data to the computer for analysis ? Built-in, user definable math functions to calculate derived parameters
Example Test Sequence

Tests: ? Leakage ? Low voltage/resistances ? LIV ? IDDQ ? I-V characterization ? Isolation and trace resistance ? Temperature coefficient ? Forward voltage, reverse breakdown, leakage current ? DC parametric test ? DC power source ? HIPOT ? Photovoltaic cell efficiency (source and sink) ? Dielectric withstanding

I

Test Test 1

Pass/Fail Test Check V F1 at 100mA against pass/fail limits Check V F2 at 1A against pass/fail limits Check leakage current at –500V ? and test against pass/fail limits

If Passes Test Go to Test 2

If Fails Test

SMU INSTRUMENTS

IR Test 3

VF1

VF2

Test 2

Go to Test 3

Test 2 Test 1

V

Test 3

1. Bin part to good bin 2. Transmit readings to computer while handler is placing new part 3. Return to Test 1

1. Bin part to bad bin 2. Transmit data to computer while handler is placing new part 3. Return to Test 1

1.888.KEITHLEY (U.S. only) www.keithley.com
A Greater Measure of Confidence

Tightly coupled precision sourcing and measurement

Automation for Speed A SourceMeter SMU instrument streamlines production testing. It sources voltage or current while making measurements without needing to change connections. It is designed for reliable operation in non-stop production environments. To provide the throughput demanded by production applications, the SourceMeter SMU instrument offers many built-in features that allow it to run complex test sequences without computer control or GPIB communications slowing things down.

Typical Applications Devices: ? Discrete semiconductor devices ? Passive devices ? Transient suppression devices ? ICs, RFICs, MMICs ? Laser diodes, laser diode modules, LEDs, photodetectors ? Circuit protection devices: TVS, MOV, Fuses, etc. ? Airbags ? Connectors, switches, relays ? High brightness LEDs (DC and?pulse)

Series 2400

SourceMeter SMU Instruments
?

Tightly coupled precision sourcing and measurement

? Locks out parallel current paths when measuring resistor networks or hybrid c ? ircuits to isolate the component under test. ? Allows users to configure and plot data easily from Series 2400 SourceMeter SMU instruments, making characterization of two, three, and four terminal devices a snap.
+

The digital I/O interface is available on all Series 2400 SoourceMeter instruments except the Model 2401. Trigger Link Interface All SourceMeter SMU instruments include Keithley’s unique Trigger Link interface which provides high-speed, seamless communications with many of Keithley’s other instruments. For example, use the Trigger Link interface to connect a SourceMeter SMU instrument with a Series 7000 Switching System for a complete multi-point test solution. With Trigger Link, the Series 7000 Switching Systems can be controlled by a SourceMeter SMU instrument during a high-speed test sequence independent of a computer and GPIB. Optional Contact Check Function The Contact Check function makes it simple to verify good connections quickly and easily before an automated test sequence begins. This eliminates measurement errors and false product failures associated with contact fatigue, breakage, contamination, loose or broken connection, relay failures, etc. Some capabilities of this function are: ? 350?s verification and notification process time ? The output of the SourceMeter SMU instrument is automatically shut off after a fault and is not re-activated until good contact is verified, protecting the device under test from damage and the operator from potential safety h ? azards. ? 3 pass/fail threshold values:?2W, 15W, and 50W ? No energy passes through the device under test during the operation. ? Enabled either from the front panel or remotely over the GPIB ? 3 fault notification methods
GUARD Pass IN/OUT HI SENSE HI V or I Source Vmeter (optional) SENSE LO IN/OUT LO Pass Fail GUARD SENSE

GUARD GUARD SENSE

Imeter IN/OUT HI SENSE HI DUT R2 Isource Vmeter R1 R3 SENSE LO IN/OUT LO

6-Wire Ohms Circuit. All test current flows through R1 because the high current guard drives the voltage across R2 to 0V.

Contact check option for 4-wire or 6-wire applications

Free LabTracer 2.0 device characterization software (downloadable)

1.888.KEITHLEY (U.S. only) www.keithley.com
A Greater Measure of Confidence

SMU INSTRUMENTS

Imeter

350?s Contact Check

Tightly coupled precision sourcing and measurement

Digital I/O Interface The digital I/O interface can link a SourceMeter SMU instrument to many popular component handlers, including Aetrium, Aeco, and Robotronics. Other capabilities of the interface include: ? Tight systems integration for applications such as binning and sorting ? Built-in component handler interface ? Start of test and end of test signals ? 5V, 300mA power supply ? Optional expander accessory (Model 2499-DIGIO) adds 16 digital I/O lines

Unique 6-Wire Ohms Technique SourceMeter SMU instruments can make standard 4-wire, split Kelvin, and 6-wire, guarded ohms measurements and can be configured for either the constant current or constant voltage method. The 6-wire ohms technique: ? Uses guard and guard sense leads in addition to the 4-wire sense and source leads.

+ -

Series 2400

SourceMeter SMU Instruments
?

Voltage Accuracy (Local or Remote Sense)
Programming Resolution 5 ?V 50 ?V 500 ?V 5 mV 5 ?V 50 ?V 500 ?V 50 mV 5 ?V 50 ?V 500 ?V 1.5 mV 5 ?V 50 ?V 500 ?V 2.5 mV 5 ?V 50 ?V 500 ?V 2.5 mV 5 ?V 50 ?V 500 ?V 5 mV Source1 Accuracy (1 Year) 23°C ±5°C ±(% rdg. + volts) 0.02% + 600 ?V 0.02% + 600 ?V 0.02% + 2.4 mV 0.02% + 24 mV 0.02% + 600 ?V 0.02% + 600 ?V 0.02% + 2.4 mV 0.02% + 100 mV 0.02% + 600 ?V 0.02% + 600 ?V 0.02% + 2.4 mV 0.02% + 7.2 mV 0.02% + 600 ?V 0.02% + 600 ?V 0.02% + 2.4 mV 0.02% + 12 mV 0.02% + 600 ?V 0.02% + 600 ?V 0.02% + 2.4 mV 0.02% + 12 mV 0.02% + 600 ?V 0.02% + 600 ?V 0.02% + 1.2 mV 0.02% + 4.8 mV Default Measurement Resolution 1??V 10??V 100??V 1 mV 1??V 10??V 100??V 10 mV 1??V 10??V 100??V 1 mV 1??V 10??V 100??V 1 mV 1??V 10??V 100??V 1 mV 1??V 10??V 100??V 1 mV Measurement 2, 3, 4 Accuracy (1?Year) 23°C ±5°C ±(% rdg. + volts) 0.012% + 300 ?V 0.012% + 300 ?V 0.015% + 1.5 mV 0.015% + 10 mV 0.012% + 300 ?V 0.012% + 300 ?V 0.015% + 1 mV 0.015% + 50 mV 0.012% + 300 ?V 0.012% + 300 ?V 0.015% + 1 mV 0.015% + 3 mV 0.012% + 300 ?V 0.012% + 300 ?V 0.015% + 1 mV 0.015% + 5 mV 0.012% + 300 ?V 0.012% + 300 ?V 0.015% + 1 mV 0.015% + 5 mV 0.012% + 300 ?V 0.012% + 300 ?V 0.015% + 750 ?V 0.015% + 3 mV Output Slew Rate (±30%) Source/Sink Limit ±21 V @ ±1.05 A ±210 V @ ±105 mA*

Model 2400, 2400-C, 2401

2410, 2410-C

2420, 2420-C

2425, 2425-C

2430, 2430-C

2440, 2440-C

Range 200.000 mV 2.00000 V 20.0000 V 200.000 V* 200.000 mV 2.00000 V 20.0000 V 1000.00 V 200.000 mV 2.00000 V 20.0000 V 60.0000 V 200.000 mV 2.00000 V 20.0000 V 100.0000 V 200.000 mV 2.00000 V 20.0000 V 100.0000 V 200.000 mV 2.00000 V 10.0000 V 40.0000 V

0.08 V/?s 0.5 V/?s

Series 2400 condensed specifications

0.15 V/?s 0.5 V/?s

±21 V @ ±1.05 A ±1100 V @ ±21 mA

0.08 V/?s 0.14 V/?s

±21 V @ ±3.15 A ±63 V @ ±1.05 A

0.08 V/?s 0.25 V/?s

±21 V @ ±3.15 A ±105 V @ ±1.05 A ±105 V @ ±1.05 A

0.08 V/?s 0.25 V/?s

±105 V @ ±10.5 A (pulse mode only) ±10.5 V @ ±5.25 A ±42 V @ ±1.05 A

0.08 V/?s 0.25 V/?s

*Not available on Model 2401. Temperature Coefficient (0°–18°C and 28°–50°C): ±(0.15 × accuracy specification)/°C. Voltage Regulation: Line:? 0.01% of range. Load: 0.01% of range + 100?V. Over Voltage Protection: User selectable values, 5% tolerance. Factory default = none. Current Limit: Bipolar current limit (compliance) set with single value. Min. 0.1% of range. Overshoot: <0.1% typical (full scale step, resistive load, 10mA range).

Additional Pulse Mode Source Specifications (2430 and 2430-C only)
Maximum Duty Cycle:?8%, hardware limited, 10A range only. All other ranges 100%. Maximum Pulse Width: 5ms from 90%?rising to 90% falling edge, 2.5ms 10A?range. Minimum Pulse Width: 150?s. Minimum Pulse Resolution: 50?s typical, 70?s max., limited by system ? jitter. Source Accuracy: Determined by settling time and source range specifications. Output Settling Time 0.1%: 800?s typ., source I = 10A?into 10W, limited by voltage slew rate. 500?s typ., source I = 10A into 1W, limited by voltage slew rate. Output Slew Rate: Voltage (10W load): 0.25V/?s ±30% on 100V?range. 0.08V/?s ±30% on 20V?range, 10A range. Current (0W load): 0.25A/?s ±30% on 100V?range. 0.08A/?s ±30% on 20V?range, 10A?range. NOTES
1. 2400, 2401, 2410 Only: Specifications valid for continuous output currents below 105mA. For operation above 105mA continuous for >1 minute, derate accuracy 10%/35mA above 105mA. 2. Speed = Normal (1 PLC). For 0.1 PLC, add 0.005% of range to offset specifications, except 200mV, 1A, 10A ranges, add 0.05%. For 0.01 PLC, add 0.05% of range to offset specifications, except 200mV, 1A, 10A ranges, add 0.5%. 3. Accuracies apply to 2- or 4-wire mode when properly zeroed. 4. In pulse mode, limited to 0.1 PLC measurement.

ADDITIONAL SOURCE?SPECIFICATIONS (All Models)
TRANSIENT RESPONSE TIME: 30?s minimum for the output to recover to its spec. following a step change in load. COMMAND PROCESSING TIME: Maximum time required for the output to begin to change following the receipt of :SOURce:VOLTage|CURRent <nrf> command. Autorange On: 10ms. Autorange Off: 7ms. OUTPUT SETTLING TIME: Time required to reach 0.1% of final value after command is processed. 100?s typical. Resistive load. 10?A to 100mA range. DC FLOATING VOLTAGE: Output can be floated up to ±250VDC (Model 2440 ±40VDC) from chassis ground. REMOTE SENSE: Up to 1V drop per load lead. COMPLIANCE ACCURACY: Add 0.3% of range and ±0.02%?of reading to base specification. OVER TEMPERATURE PROTECTION: Internally sensed temperature overload puts unit in standby mode. RANGE CHANGE OVERSHOOT: Overshoot into a fully resistive 100k W load, 10Hz to 1MHz BW, adjacent ranges: 100mV typical, except 20V/200V (20V/60V on Model 2420), 20V/100V on Model 2425 and 2430, range boundary, and Model 2440. MINIMUM COMPLIANCE VALUE: 0.1% of range.

SMU INSTRUMENTS

1.888.KEITHLEY (U.S. only) www.keithley.com
A Greater Measure of Confidence

Series 2400 condensed specifications

Series 2400

SourceMeter SMU Instruments
?

Current Accuracy (Local or Remote Sense)
Source 1, 3 Accuracy (1 Year) 23°C ±5°C ±(% rdg. + amps) 0.035% + 600 pA 0.033% + ?? 2 nA 0.031% + ? 20 nA 0.034% + 200 nA 0.045% + ?? 2 ?A 0.066% + ? 20 ?A 0.27? % + 900 ?A 0.035% + 600 pA 0.033% + ?? 2 nA 0.031% + ? 20 nA 0.034% + 200 nA 0.045% + ?? 4 ?A 0.066% + ? 20 ?A 0.27? % + 900 ?A 0.033% + ?? 2 nA 0.031% + ? 20 nA 0.034% + 200 nA 0.045% + ?? 2 ?A 0.066% + ? 20 ?A 0.067% + 900 ?A 0.059% + 2.7 mA 0.033% + ?? 2 nA 0.031% + ? 20 nA 0.034% + 200 nA 0.045% + ?? 2 ?A 0.066% + ? 20 ?A 0.067% + 900 ?A 0.059% + 2.8 mA 0.033% + ?? 2 nA 0.031% + ? 20 nA 0.034% + 200 nA 0.045% + ?? 2 ?A 0.066% + ? 20 ?A 0.067% + 900 ?A 0.059% + 2.8 mA 0.089% + 5.9 mA 0.033% + ?? 2 nA 0.031% + ? 20 nA 0.034% + 200 nA 0.045% + ?? 2 ?A 0.066% + ? 20 ?A 0.067% + 900 ?A 0.10? % + 5.4 mA Measurement 5, 6, 7 Accuracy (1?Year) 23°C ±5°C ±(% rdg. + amps) 0.029% + 300 pA 0.027% + 700 pA 0.025% + ?? 6 nA 0.027% + ? 60 nA 0.035% + 600 nA 0.055% + ?? 6 ?A 0.22? % + 570 ?A 0.029% + 300 pA 0.027% + 700 pA 0.025% + ?? 6 nA 0.027% + ? 60 nA 0.035% + 1.2 ?A 0.055% + ?? 6 ?A 0.22? % + 570 ?A 0.027% + 700 pA 0.025% + ?? 6 nA 0.027% + ? 60 nA 0.035% + 600 nA 0.055% + ?? 6 ?A 0.066% + 570 ?A 0.052% + 1.71 mA 0.027% + 700 pA 0.025% + ?? 6 nA 0.027% + ? 60 nA 0.035% + 600 nA 0.055% + ?? 6 ?A 0.060% + 570 ?A 0.052% + 1.71 mA 0.027% + 700 pA 0.025% + ?? 6 nA 0.027% + ? 60 nA 0.035% + 600 nA 0.055% + ?? 6 ?A 0.060% + 570 ?A 0.052% + 1.71 mA 0.082% + 1.71 mA 0.027% + 700 pA 0.025% + ?? 6 nA 0.027% + ? 60 nA 0.035% + 600 nA 0.055% + ?? 6 ?A 0.060% + 570 ?A 0.10? % + 3.42 mA

Model

Series 2400 condensed specifications

2410, 2410-C

±1.05A @ ±21 V ±21 mA @ ±1100 V

2420, 2420-C

±3.15A @ ±21 V ±1.05 A @ ±63 V

2425, 2425-C

±3.15A @ ±21 V ±1.05 A @ ±105 V

±1.05A @ ±105 V ±10.5 A @ ±105 V (pulse mode only)

2430, 2430-C

2440, 2440-C

±5.25A @ ±10.5 V ±1.05 A @ ±42 V

Contact Check Specifications (requires -C?version)
(Not available for Model 2401) Speed: 350?s for verification and notification. Contact Check: 2 W 15 W 50 W No contact check failure <1.00 W <13.5 W <47.5 W Always contact check failure >3.00 W >16.5 W >52.5 W

1.888.KEITHLEY (U.S. only) www.keithley.com
A Greater Measure of Confidence

SMU INSTRUMENTS

Temperature Coefficient (0°–18°C and 28°–50°C): ±(0.15 × accuracy specification)/°C. CURRENT Regulation: Line:? 0.01% of range. Load: 0.01% of range (except Model 2440 5A?range 0.05%) + 100pA. Voltage LIMIT: Bipolar voltage limit (compliance) set with single value. Min. 0.1% of range. OVERSHOOT: <0.1% typical (1mA step, RL = 10k W, 20V range for Model 2400, 2401, 2410, 2420, 2425, 2430), (10V range for Model 2440).

NOTES
1. 2400, 2401, 2410 Only: Specifications valid for continuous output currents below 105mA. For operation above 105mA continuous for >1 minute, derate accuracy 10%/35mA above 105mA. 2. Full operation (1A) regardless of load to 30°C (50°C for Model 2420 and 2440). Above 30°C (50°C for Model 2420 and 2440) ambient, derate 35mA/°C and prorate 35mA/W load. 4-wire mode. For current sink operation on 1A, 3A, or 5A ranges, maximum continuous power is limited to approximately 1/2 rated power or less, depending on current, up to 30°C?ambient. See power equations in the User’s Manual to calculate allowable duty cycle for specific conditions. 3. For sink mode, 1?A to 100mA?range, accuracy is: Model 2400, 2401: ±(0.15% +?offset*4). Models 2410, 2420, 2425, 2430, 2440: ±(0.5% + offset*3). For 1A?range, accuracy is: Model 2400, 2401: ±(1.5% +?offset*8). Models 2410, 2420, 2425, 2430, 2440: ±(1.5% + offset*3). 4. 10A?range only in pulse mode. Limited to 2.5ms pulse width maximum. 10% duty cycle maximum. 5. Speed = Normal (1 PLC). For 0.1 PLC, add 0.005% of range to offset specifications, except 200mV, 1A, 10A ranges, add 0.05%. For 0.01 PLC, add 0.05% of range to offset specifications, except 200mV, 1A, 10A ranges, add?0.5%. 6. Accuracies apply to 2- or 4-wire mode when properly zeroed. 7. In pulse mode, limited to 0.1 PLC measurement. 8. Model 2400 and 2400-C only.

Series 2400 condensed specifications

2400, 2400-C, 2401

Range 1.00000 ?A 10.0000 ?A 100.000 ?A 1.00000 mA 10.0000 mA 100.000 mA 1.00000 A 2 1.00000 ?A 10.0000 ?A 100.000 ?A 1.00000 mA 20.0000 mA 100.000 mA 1.00000 A 2 10.0000 ?A 100.000 ?A 1.00000 mA 10.0000 mA 100.000 mA 1.00000 A 2 3.00000 A 2 10.0000 ?A 100.000 ?A 1.00000 mA 10.0000 mA 100.000 mA 1.00000 A 2 3.00000 A 2 10.0000 ?A 100.000 ?A 1.00000 mA 10.0000 mA 100.000 mA 1.00000 A 3.00000 A 2 10.00000 A4 10.0000 ?A 100.000 ?A 1.00000 mA 10.0000 mA 100.000 mA 1.00000 ? A 5.00000 ? A

Programming Resolution ? 50 pA 500 pA ??5 nA ? 50 nA 500 nA ??5 ?A ? 50 ?A ? 50 pA 500 pA ??5 nA ? 50 nA 500 nA ??5 ?A ? 50 ?A 500 pA ??5 nA ? 50 nA 500 nA ??5 ?A ? 50 ?A ? 50 ?A 500 pA ??5 nA ? 50 nA 500 nA ??5 ?A ? 50 ?A ? 50 ?A 500 pA ??5 nA ? 50 nA 500 nA ??5 ?A ? 50 ?A 500 ?A 500 ?A 500 pA ??5 nA ? 50 nA 500 nA ??5 ?A ? 50 ?A ? 50 ?A

Default Measurement Resolution ? 10 pA 100 pA ??1 nA ? 10 nA 100 nA ??1 ?A ? 10 ?A ? 10 pA 100 pA ??1 nA ? 10 nA 100 nA ??1 ?A ? 10 ?A 100 pA ??1 nA ? 10 nA 100 nA ??1 ?A ? 10 ?A ? 10 ?A 100 pA ??1 nA ? 10 nA 100 nA ??1 ?A ? 10 ?A ? 10 ?A 100 pA ??1 nA ? 10 nA 100 nA ??1 ?A ? 10 ?A ? 10 ?A ? 10 ?A 100 pA ??1 nA ? 10 nA 100 nA ??1 ?A ? 10 ?A ? 10 ?A

Source/Sink Limit

±1.05A @ ±21 V ±105 mA @ ±210 V 8

Series 2400

SourceMeter SMU Instruments
?

Resistance Measurement Accuracy (Local or Remote Sense)1, 2, 5
Default Test Current 2400, 2401, 2410 – – 100 mA 10 mA 1 mA 100 ?A 10 ?A 1 ?A 1 ?A 100 nA – Default Test Current 2420, 2425, 2430, 2440 – 1 A 100 mA 10 mA 1 mA 100 ?A 10 ?A 1 ?A 1 ?A – – Normal Accuracy (23°C ±5°C) 1 Year, ±(% rdg. + ohms) 2400, 2401 Source I ACC + Meas. VACC Source I ACC + Meas VACC 0.10% + 0.003 W 0.08% + 0.03 W 0.07% + 0.3 W 0.06% + 3 0.07% + 30 0.11% + 300 0.11% + 1 W W W kW 2410 Source I ACC + Meas. VACC Source I ACC + Meas. VACC 0.11% + 0.006 W 0.09% + 0.1 W 0.08% + 0.6 W 0.07% + 6 0.07% + 60 0.12% + 600 W W W 2420, 2425, 2430, 2440 Source I ACC + Meas. VACC 0.17% + 0.0003 W 0.10% + 0.003 W 0.08% + 0.03 W 0.07% + 0.3 0.06% + 3 0.07% + 30 0.11% + 300 0.11% + 1 W W W W kW Enhanced Accuracy (23°C ±5°C) 4 1 Year, ±(% rdg. + ohms) 2400, 2401 Source I ACC + Meas. VACC Source I ACC + Meas. VACC 0.05% + 0.01 0.05% + 0.1 0.04% + 1 0.05% + 10 0.05% + 100 0.05% + 500 W W W W W W 0.07% + 0.001 W

Range <0.20000 W3 2.00000 W3 20.0000 W 200.000 W 2.00000 k W 20.0000 k W

Default Resolution – 10 ?W 100 ?W 1 mW 10 mW 100 mW

Series 2400 condensed specifications

200.000 k W 1 W W 2.00000 MW6 10 20.0000 MW7 100 W 200.000 MW3 >200.000 MW3 1 k W –

0.12% + 2.4 k W 0.66% + 24 k W Source I ACC + Meas. VACC

0.66% + 10 k W Source I ACC + Meas. VACC NOTES

Source I ACC + Meas. VACC Source I ACC + Meas. VACC

0.35% + 5 kW Source I ACC + Meas. VACC

TEMPERATURE COEFFICIENT (0°–18°C and 28°–50°C): ±(0.15 × accuracy specification)/°C. Source I Mode, Manual Ohms: Total uncertainty = I source accuracy + V measure accuracy (4-wire remote sense). Source V Mode, Manual Ohms: Total uncertainty = V source a ? ccuracy + I measure accuracy (4-wire remote sense). 6-wire ohms mode: Available using active ohms guard and guard sense. Max. Guard Output Current: 50mA (except 1A range). Accuracy is load dependent. Refer to White Paper no. 2033 for calculation f ?ormula. Guard Output Impedance: <0.1W in ohms mode.

1. Speed = Normal (1 PLC). For 0.1 PLC, add 0.005% of range to offset specifications, except 200mV, 1A, 10A?ranges, add 0.05%. For 0.01 PLC, add 0.05% of range to offset specifications, except 200mV, 1A, 10A ranges, add 0.5%. 2. Accuracies apply to 2- or 4-wire mode when properly zeroed. 3. Manual ohms only – except 2420, 2425, 2430, 2440 for 2W range and 2400, 2401, or 2410 for 200MW range. 4. Source readback enabled, offset compensation ON. Also available on 2410, 2420, 2425, 2430, and 2440 with similar a ? ccuracy enhancement. 5. In pulse mode, limited to 0.1 PLC measurement. 6. Except 2440; default test current is 5?A. 7. Except 2440; default test current is 0.5?A.

Services Available
2400-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2400-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2401-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2410-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2410-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2420-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2420-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2425-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2425-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2430-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2430-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2440-3Y-EW 1-year factory warranty extended to 3 years from date of shipment 2440-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment C/2400-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2400, 2400-C, 2400-LV* C/2401-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Model 2401* C/2410-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2410, 2410-C* C/2420-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2420, 2420-C* C/2425-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2425, 2425-C* C/2430-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2430, 2430-C* C/2440-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2440, 2440-C* TRN-2400-1-C Course: Unleashing the Power of Your SourceMeter SMU Instrument *Not available in all countries

SMU INSTRUMENTS

1.888.KEITHLEY (U.S. only) www.keithley.com
A Greater Measure of Confidence

Series 2400 condensed specifications

Series 2400
System Speeds
Measurement1
MAXIMUM RANGE CHANGE RATE: 75/second. MAXIMUM MEASURE AUTORANGE TIME: 40ms (fixed source).2

SourceMeter SMU Instruments
?

Sweep Operation3 Reading Rates (rdg./second) for 60Hz (50Hz):
Speed NPLC/Trigger Origin 0.01 / internal 0.01 / external 0.01 / internal 0.01 / external 0.10 / internal 0.10 / external 1.00 / internal 1.00 / external Measure To Mem. To GPIB 2081 (2030) 1754 1239 (1200) 1254 2081 (2030) 1198 (1210) 1239 (1200) 1079 (1050) 510 (433) 509 (433) 438 (380) 438 (380) 59 (49) 59 (49) 57 (48) 57 (48) Source-Measure To Mem. To GPIB 1551 (1515) 1369 1018 (990) 1035 1551 (1515) 1000 (900) 1018 (990) 916 (835) 470 (405) 470 (410) 409 (360) 409 (365) 58 (48) 58 (48) 57 (48) 57 (47) Source-Measure5 Pass/Fail Test4, 5 To Mem. To GPIB 902 (900) 981 830 (830) 886 902 (900) 809 (840) 830 (830) 756 (780) 389 (343) 388 (343) 374 (333) 374 (333) 56 (47) 56 (47) 56 (47) 56 (47) Source-Memory4 To Mem. To GPIB 165 (162) 165 163 (160) 163 165 (162) 164 (162) 163 (160) 162 (160) 133 (126) 132 (126) 131 (125) 131 (125) 44 (38) 44 (38) 44 (38) 44 (38)

Series 2400 condensed specifications

Fast IEEE-488.1 Mode Fast IEEE-488.2 Mode Medium IEEE-488.2 Mode Normal IEEE-488.2 Mode

Single Reading Operation Reading Rates (rdg./second) for 60Hz (50Hz):
Speed Fast (488.1) Fast (488.2) Medium (488.2) Normal (488.2) NPLC/Trigger Origin 0.01 / internal 0.01 / internal 0.10 / internal 1.00 / internal Measure To GPIB 537 256 (256) 167 (166) 49 (42) Source-Measure5 To GPIB 140 79 (83) 72 (70) 34 (31) Source-Measure Pass/Fail Test4,5 To GPIB 135 79 (83) 69 (70) 35 (30)

Component for 60Hz (50Hz): 4, 6
Speed Fast Medium Normal NOTES
Reading rates applicable for voltage or current measurements. Auto zero off, autorange off, filter off, display off, trigger delay = 0, and binary reading format. Purely resistive lead. 1?A and 10?A ranges <65ms. 3 1000 point sweep was characterized with the source on a fixed range.
1 2

NPLC/Trigger Origin 0.01 / external 0.10 / external 1.00 / external

Measure To GPIB 1.04 ms (1.08 ms) 2.55 ms (2.9 ms) 17.53 ms (20.9 ms)

Source Pass/Fail Test 0.5 ms (0.5 ms) 0.5 ms (0.5 ms) 0.5 ms (0.5 ms)

Source-Measure Pass/Fail Test5, 7 To GPIB 4.82 ms (5.3 ms) 6.27 ms (7.1 ms) 21.31 ms (25.0 ms)

Pass/Fail test performed using one high limit and one low math limit. Includes time to re-program source to a new level before making m ? easurement. 6 Time from falling edge of START OF TEST signal to falling edge of end of test signal. 7 Command processing time of :SOURce:VOLTage|CURRent:TRIGgered <nrf> command not included.
4 5

general Noise Rejection:
Fast Medium Slow
1

NPLC 0.01 0.1 1

NMRR — — 60 dB

CMRR 80 dB 80 dB 100 dB1

Except lowest 2 current ranges = 90dB.

1.888.KEITHLEY (U.S. only) www.keithley.com
A Greater Measure of Confidence

SMU INSTRUMENTS

Load Impedance: Stable into 20,000pF typical. Common mode voltage: 250V DC (40V?DC?for Model 2440). Common Mode Isolation: >109W, <1000pF. OVERRANGE: 105% of range, source and measure. Max. Voltage Drop Between Input/Output and sense terminals: 5V. Max. Sense Lead Resistance: 1MW for rated accuracy. SENSE INPUT IMPEDANCE: >1010W. GUARD?OFFSET?VOLTAGE: <150?V, typical (300?V for Models 2430, 2440). Source Output modes: Pulse (Model 2430 only) Fixed DC level Memory List (mixed function) Stair (linear and log) Memory Buffer: 5,000 readings @ 5 digits (two 2,500 point buffers). Includes selected measured backup (3 yr+ battery life). value(s) and time stamp. Lithium battery ? SOURCE?MEMORY?LIST: 100 points max.

Programmability: IEEE-488 (SCPI-1995.0), RS-232, 5 user-definable power-up states plus factory default and *RST. Digital Interface: Interlock: Active low input. Handler Interface: Start of test, end of test, 3 category bits. +5V@ 300mA supply. Not?available on Model 2401. Digital I/O: 1 trigger input, 4 TTL/Relay Drive outputs (33V @ 500mA, diode clamped). Not?available on Model 2401. Power Supply: 100V to 240V rms, 50–60Hz (automatically detected at power up). Model 2400, 2401: 190VA. Model 2410: 210VA. Model 2420: 220VA. Model 2425, 2430: 250VA. Model 2440: 240VA. COOLING: Model 2401: Convection. Model 2410, 2420, 2425, 2430, 2440:?Forced air, variable?speed. EMC: Conforms to European Union Directive 89/336/EEC, EN 61326-1. Safety: UL listed to UL 61010B-1:2003: Conforms to European Union Low Voltage Directive. Vibration: MIL-PRF-28800F?Class 3 Random. WARM-UP: 1 hour to rated accuracies. DIMENSIONS: 89mm high × 213mm wide × 370mm deep (3? in × 83?8 in × 149?16 in). Bench Configuration (with handle and feet):104mm high × 238mm wide × 370mm deep (41?8 in × 93?8 in × 149?16 in). WEIGHT: 3.21kg (7.08 lbs) (Model 2425, 2430, 2440:?4.1kg, 9.0 lbs). ENVIRONMENT: Operating: 0°–50°C, 70% R.H. up to 35°C. Derate 3% R.H./°C, 35°–50°C. Storage: –25°C to 65°C.

Series 2400 condensed specifications


相关文章:
数字源表
2400数字源表在压敏电阻... 3页 1下载券数​字​源​表 暂无评价|0人阅读|0次下载|举报文档 数​字​源​表数字源表 1. 输出模式:恒压源模式、...
Keithley吉时利2001型七位半数字多用表
Keithley吉时利2001型七位半数字多用表_信息与通信_工程科技_专业资料。Keithley ...恒流源 开路检测 直流电流 灵敏度 量程 基本准确度 在线电流 交流电流(TRMS) ...
Keithley 2410快速索引
Keithley 2410 快速索引 简介: 本手册帮助使用者熟悉 Keithley2400 系列数字源表...Keithley manual(中文) 13页 4下载券 KEITHLEY的使用方法 暂无评价 1页 免费喜欢...
高精度相位伏安表SMG2000E和数字源表2400型价格
高精度相位伏安表SMG2000E和数字源表2400型价格_...质说明:丁腈橡胶 (字母代表 NBR)耐热 100 度 耐...美国吉时利 KEITHLEY 主要特点及优点 2400 系列提供宽...
2600系列数字源表,用于半导体测试
Keithley2700中文使用手... 137页 免费 吉时利基础测量 9页 免费 基于2600A系列数字源表的... 8页 免费 2400数字万用表中文说明... 14页 1下载券©...
电参数测试仪和精密型数字源表价格_图文
电参数测试仪和精密型数字源表价格_电力/水利_工程...橡胶材质说明:丁腈橡胶 (字母代表 NBR)耐热 100 度...美国吉时利 KEITHLEY 主要特点及优点 2400 系列提供宽...
I-V测试注意
2.将 Keithley,2612B 数字源表开关打开。 3. 打开 KEITHLEY2612B Dual Source Meter 软件,输入 Start(v),End(v),Points(single loop)等参数值。 4.进行所...
译文CH3NH3PbI3TiO2 Heterojunction Solar Cells_图文
入射光子到当前转化效率说明了提取电子对是在一个给定的入射光子波长的比例。 ...通过施加在 电池外篇部的光电流和Keithley2400数字源表来测量I-V曲线。 该...
LED数码显示屏数字功率表和电流测量仪表TSGC2-9KW价格_...
说明:丁腈橡胶 (字母代表 NBR)耐热 100 度 耐...和数字源表 2400 型 参数 主要技术参数: 【商品...美国吉时利 KEITHLEY 主要特点及优点 2400 系列提供宽...
接地电阻的测量与要求
测量方法 图 4-42 说明用来测试一个接点的接触电阻的基本配置。使用具有四端...Keithley 2182A 型纳伏表和 2400 系列数字源表仪器进行 接触电阻测量的测试配置...
更多相关标签:
keithley2400说明书 | keithley 2400 | keithley 2400 价格 | keithley2400 labview | keithley2400测量软件 | keithley2400软件 | keithley 2400 二手 | keithley 2400测电流 |