当前位置:首页 >> 机械/仪表 >>

ASTM钢管标准1


ASTM 钢管标准 1 A1000-99 弹簧专用碳钢和合金钢钢丝规范 A1001-99 大型材高强度钢铸件规范 A1002-99 镍铝类合金铸件规范 A100-93(2000) 硅铁 A101-93(2000) 铬铁 A102-93(2000) 钒铁合金 A105/A105M-01 管系部件用碳素钢锻件 A106-999e1 高温用无缝碳素钢管 A108-99 优质冷加工碳素钢

棒材技术规范 A109/A109M-00e1 冷轧碳素钢带技术规范 A111-99a 电话和电报线路用镀锌"铁"丝规格 A116-00 镀锌钢丝编织栏栅网 A121-99 镀锌刺钢丝 A123/A123M-00 钢铁产品的锌镀层(热浸镀锌)技术规范 A125-96 热处理螺旋形钢弹簧 A126-95(2001) 阀门、法兰和管配件用灰铁铸件 A128/A128M-93(1998) 钢铸件,奥氏体锰 A131/A131M-94 海船用结构钢 A132-89(2000) 钼铁合金 A134-96 电熔(电弧)焊钢管(NPS 为 16 英寸和 16 英寸以上) A135-01 电阻焊钢管 A139-00 电熔(电弧)焊钢管(4 英寸以上的) A143-74(1999) 热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序 A146-64(2000) 氧化钼制品 A148/A148M-01 结构用高强度钢铸件 A153/A153M-00 钢铁制金属构件上镀锌层(热浸) A159-83(2001) 汽车用灰铁铸件 A167-99 不锈钢和耐热铬镍钢板、薄板及带材 A176-99 不锈钢和耐热铬钢板、薄板及带材 A178/A178M-95(2000) 电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范 A179/A179M-90a(1996)e1 热交换器和冷凝器用无缝冷拉低碳钢管 A181/A181M-01 普通锻制碳素钢管的规格 A182/A182M-01 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件 A183-98 钢轨用碳素钢螺栓和螺母 A184/A184M-01 混凝土加筋用变形钢筋编织网 A185-97 钢筋混凝土用焊接钢丝结构 A1-00 碳素钢丁字轨 A192/A192M-91(1996)e1 高压用无缝碳素钢锅炉管 A193/A193M-01 高温设备用合金钢和不锈钢螺栓材料 A194/A194M-01 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格 A197/A197M-00 化铁炉用可锻铸铁 A20/A20M-01 压力容器用钢板材通用要求 A202/A202M-93(1999) 压力容器用铬锰硅合金钢板

A203/A203M-97 压力容器用镍合金钢板 A204/A204M-93(1999) 压力容器用钼合金钢板 A209/A209M-98 锅炉和过热器用无缝碳钼合金钢管 A210/A210M-96 锅炉和过热器用无缝中碳素管 A213/A213M-01 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管 A214/A214M-96 热交换器与冷凝器用电阻焊接碳素钢管 A216/A216M-93(1998) 高温下使用的适合于熔焊的碳素钢铸件规格 A217/A217M-01 适合高温受压零件用合金钢和马氏体不锈钢铸件 A21-94(1999) 铁路用未经热处理和经热处理的碳素钢轴 A220/A220M-99 珠光体可锻铁 A225/A225M-93(1999) 压力容器用锰矾镍合金钢板 A227/A227M-99 机械弹簧用冷拉钢丝 A228/A228M-00 乐器用优质弹簧钢丝 A229/A229M-99 机械弹簧用油回火的钢丝 A230/A230M-99 阀门用油回火优质碳素钢弹簧丝 A231/A231M-96 铬钒合金钢弹簧丝 A232/A232M-99 阀门用优质铬钒合金钢弹簧丝 A234/A234M-00a 中温与高温下使用的锻制碳素钢及合金钢管配件 A239-95(1999) 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法 A240/A240M-01 压力容器用耐热铬及铬镍不锈钢板、薄板及带材 A242/A242M-00a 高强度低合金结构钢 A247-67(1998) 铁铸件中石墨显微结构评定试验方法 A249/A249M-01 锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管 A250/A250M-95(2001) 锅炉和过热器用电阻焊铁素体合金钢管 A252-98e1 焊接钢和无缝钢管桩 A254-97 铜焊钢管规格 A255-99 测定钢淬透性用末端淬火试验的标准试验方法 A262-98 奥氏体不锈钢晶间浸蚀敏感性的检测 A263-94a(1999) 耐腐蚀铬钢包覆板材,薄板材及带材技术规范 A264-94a(1999) 包覆的不锈铬镍钢板,薄板及带材规格 A265-94a(1999) 镍和镍基合金包覆钢板规格 A266/A266M-99 压力容器部件用碳素钢锻件规格 A268/A268M-01 一般设备用无缝和焊接铁素体与马氏体不锈钢管 A269-01 一般设备用无缝和焊接奥氏体不锈钢管 A27/A27M-95(2000) 通用碳素钢铸件 A270-01 卫生设施用无缝钢和焊接奥氏体不锈钢管 A275/A275M-98 钢锻件的磁粉检查试验方法 A276-00a 不锈钢棒材和型材 A278-93 适用于 650F 容压部件用灰铸铁件的技术规范 A283/A283M-00 低和中等抗拉强度碳素钢板 A285/A285M-90(2001) 压力容器用低和中等抗拉强度的碳素钢板 A288-91(1998) 涡轮发电机磁性定位环用碳素钢和合金钢锻件 A289/A289M-97 发电机非磁性定位环用合金钢锻件的技术规范 A29/A29M-99e1 热锻及冷加工碳素钢和合金钢棒

A2-90(1997) 普通型,带槽和防护型碳素工字钢轨 A290-95(1999) 减速器环用碳素钢和合金钢锻件 A291-95(1999) 减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件 A295-98 高碳耐磨轴承钢技术规范 A297/A297M-97(1998) 一般用耐热铬铁与镍铬铁合金钢铸件规格 A299/A299M-97e1 压力容器用锰硅碳钢板 A302/A302M-97e1 压力容器用锰钼和锰钼镍合金钢板 A304-96 有末端淬火淬透性要求的合金钢棒材的技术规范 A307-00 抗拉强度为 60000psi 的碳素钢螺栓和螺柱的技术规范 A308-99 经热浸处理镀有铅锡合金的薄板材的技术规范 A309-94a(1999) 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法 A311/A311M-95(2000) 有机械性能要求的消除应力的冷拉碳素钢棒 A312/A312M-00c 无缝和焊接奥氏体不锈钢管 A313/A313M-98 不锈钢弹簧丝技术规范 A314-97 锻造用不锈及耐热钢坯及钢棒规格 A31-00 钢铆钉及铆钉和压力容器用棒材 A319-71(2001) 高温无压部件用灰铁铸件 A320/A320M-01 低温用合金钢螺栓材料规格 A321-90(1995)e1 经淬火和回火的碳素钢棒 A322-91(1996) 合金钢棒材.级别 A323-93(2000) 硼铁规格 A324-73(2000) 钛铁合金 A325-00 经热处理最小抗拉强度为 120/105ksi 的钢结构螺栓 A325M-00 结构钢连接件用高强度螺栓(米制) A327-91(1997) 铸铁冲击试验方法 A327M-91(1997) 铸铁冲击试验方法(米制) A328/A328M-00 薄钢板桩 A331-95(2000) 冷加工合金钢棒 A333/A333M-99 低温用无缝与焊接钢管规格 A334/A334M-99 低温设备用无缝与焊接碳素和合金钢管 A335/A335M-01 高温用无缝铁素体合金钢管 A336/A336M-99e1 压力与高温部件用合金钢锻件规格 A338-84(1998) 铁路,船舶和其他重型装备在温度达到 650 华氏度(345 摄氏度)时使用的可锻铸铁法兰,管件和阀 门零件 ASTM 钢管标准 2 A34/A34M-96 磁性材料的抽样和采购试验的标准惯例 A340-99a 有关磁性试验用符号和定义的术语 A341/A341M-00 用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法 A342/A342M-99 磁铁材料导磁率的试验方法 A343-97 在电力频率下用瓦特计-安培计-伏特计法(100-1000 赫兹)和 25 厘米艾普斯亭(EPSTEIN) 机架测定材 料的交流电磁性能的试验方法 A345-98 磁设备用平轧电炉钢 A348/A348M-00 用瓦特计--安培计--伏特计法(100-10000 赫兹)和 25 厘米艾普斯亭框测定材料的交流磁性能 的试验方法

A350/A350M-00c 要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范 A351/A351M-00 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范 A352/A352M-93(1998) 低温受压零件用铁素体和马氏体钢铸件规格 A353/A353M-93(1999) 压力容器用经二次正火及回火处理的含 9%镍的合金钢板 A354-01 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格 A355-89(2000) 渗氮用合金钢棒 A356/A356M-98e1 蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件 A358/A358M-01 高温用电熔焊奥氏体铬镍合金钢管 A36/A36M-00a 碳素结构钢技术规范 A363-98 地面架空线用镀锌钢丝绳 A367-60(1999) 铸铁的激冷试验方法 A368-95a(2000) 不锈钢和耐热钢丝绳的标准 A369/A369M-01 高温用锻制和镗孔碳素钢管和铁素体合金钢管 A370-97a 钢制品机械测试的标准试验方法和定义 A372/A372M-99 薄壁压力容器用碳素钢及合金钢锻件 A376/A376M-01 高温中心站用无缝奥氏钢管 A377-99 球墨铸铁压力管规范索引 A380-99e1 不锈钢零件、设备和系统的清洗和除垢 A381-96 高压输送用金属弧焊钢管 A384-76(1996) 防止钢组件热浸镀锌时翘曲和扭曲用安全保护 A385-00 提供高质量镀锌覆层(热浸) A3-01 低、中、高碳素钢鱼尾(连接)板 A387/A387M-99e1 压力容器用铬钼合金钢板 A388/A388M-95(2000)e1 重型钢锻件超声波检测 A389/A389M-93(1998) 适合高温受压部件用经特殊热处理的合金钢铸件规格 A390-95(2001) 饲养家禽用镀锌钢丝栏栅网(六角形和直线形) A391/A391M-98 80 号合金钢链条 A392-96 镀锌钢丝链环栏栅网 A394-00 传动塔架用镀锌和裸露钢螺栓 A395/A395M-99 高温用铁素体球墨铸铁受压铸件 A400-69(2000) 钢棒的成分及机械性能选择指南 A401/A401M-98 铬硅合金钢丝 A403/A403M-00b 锻制奥氏体不锈钢管配件 A407-93(1998) 盘簧用冷拉钢丝 A409/A409M-01 腐蚀场所或高温下使用的焊接大口径奥氏体钢管 A411-98 镀锌低碳钢铠装线 A413/A413M-00 碳素钢链 A414/A414M-00 压力容器用碳素薄钢板 A416/A416M-99 预应力混凝土用无涂层七股钢铰线 A417-93(1998) 之字型、方型和正弦型装垫弹簧元件用冷拉钢丝 A418-99 涡轮机及发电机钢转子锻件的超声波检查方法 A420/A420M-00b 低温下用锻制碳素钢和合金钢管配件 A421/A421M-98a 预应力混凝土用无涂层消除应力钢丝的技术规范 A423/A423M-95(2000) 无缝和电焊低合金钢管

A424-00 搪瓷用钢薄板 A426-92(1997) 高温用离心铸造的铁素体合金钢管 A427-74(1996)e1 冷轧和热轧用锻制合金钢辊 A428/A428M-01 钢铁制品上铝覆层重量的测试方法 A434-90a(2000) 热轧与冷精轧经回火及淬火的合金钢棒 A435/A435M-90(2001) 钢板的直射束纵向超声波检验 A436-84(1997)e1 奥氏体灰口铁铸件 A437/A437M-01 高温用经特殊处理的涡轮型合金钢螺栓材料 A438-80(1997) 灰铸铁横向弯曲试验 A439-83(1999) 奥氏体可锻铸铁铸件 A447/A447M-93(1998) 高温用镍铬铁合金钢铸件(25-12 级) A449-00 经淬火和回火的钢螺栓和螺柱 A450/A450M-96a 碳素钢管、铁素体合金钢管及奥氏体合金钢管 A451-93(1997) 高温用离心铸造的奥氏体钢管 A453/A453M-00 具有同奥氏体钢相类似的膨胀系数、屈服强度为 50-120Ksi(345-827MPa)的耐高温螺栓材料 A455/A455M-90(2001) 压力容器用高强度碳锰钢板 A456/A456M-99 大型曲轴锻件的磁粉检查 A459-97 镀锌平轧扁钢铠装带 A460-94(1999) 包铜钢丝绳标准 A463/A463M-00 热浸镀铝薄钢板 A466/A466M-98 非焊接碳素钢链 A467/A467M-98 机器链和盘旋链 A469-94a(1999) 用于发电机转子的真空处理钢锻件 A470-01 涡轮机转子和轴用经真空处理的碳素钢和合金锻件 A471-94(1999) 涡轮转子转盘和转轮用真空处理合金钢锻件技术规范 A472-98 蒸汽涡轮机轴及转子锻件的热稳定性的试验方法 A473-01 不锈和耐热钢锻件 A474-98 包铝钢丝绳标准 A475-98 镀锌钢丝绳 A476/A476M-00 造纸厂干燥辊用球墨可锻铸铁件 A478-97 铬镍不锈钢和耐热钢制编织钢丝 A479/A479M-00 锅炉及压力容器用不锈钢和耐热钢棒与型材 A47/A47M-99 铁素体可锻铁铸件 A480/A480M-01 扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求 A481-94(2000) 金属铬 A482-93(2000) 铬铁硅 A483-64(2000) 硅锰合金 A484/A484M-00 不锈及耐热锻钢棒,钢坯及锻件的规格 A485-00 高淬透性耐磨轴承钢的技术规范 A487/A487M-93(1998) 受压钢铸件 A488/A488M-01 钢铸件焊接规程和工作人员的合格鉴定 A48-94ae1 灰铁铸件 A489-00 碳素钢吊耳 A490-00 最小拉伸强度为 150 千磅/平方英寸热处理钢结构螺栓

A491-96 镀铝钢链环栏栅结构 A492-95(2000) 耐热不锈钢丝绳 A493-95(2000) 冷镦和冷锻不锈钢和耐热钢丝 A494/A494M-00 镍和镍合金铸件 A495-94(2000) 硅钙合金钢技术规范 A496-97ae1 钢筋混凝土用变形钢丝 A497-99e1 钢筋混凝土用焊接变形钢丝网 A498-98 无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管 A49-01 经热处理的碳素钢鱼尾(连接)板,微合金鱼尾板及锻制碳素钢异型鱼尾板 A499-89(1997)e1 轧制丁字钢轨用的碳素钢棒材及型材的技术规范 A500-01 圆形与异型焊接与无缝碳素钢结构管 A501-01 热成型焊接与无缝碳素钢结构管 A503/A503M-01 锻制大型曲轴的超声波检验 A504-93(1999) 锻制碳素钢轮 A505-00 热轧和冷轧合金钢薄板和带材 A506-00 正规质量及优质结构的热轧和冷轧合金钢薄板与带材 A507-00 优质拉拔,热轧和冷轧合金钢薄板与带材 A508/A508M-95(1999) 压力容器用经回火和淬火真空处理的碳素钢与合金钢锻件 A510-00 碳素钢盘条和粗圆钢丝通用要求 A510M-00 碳素钢盘条和粗圆钢丝(米制) A511-96 无缝不锈钢机械管 A512-96 冷拉对缝焊碳素钢机械管 A513-00 电阻焊碳素钢与合金钢机械钢管 A514/A514M-00a 焊接用经回火与淬火的高屈服强度合金钢板 A515/A515M-92(1997) 中温及高温压力容器用碳素钢板 A516/A516M-90(2001) 中温及低温压力容器用碳素钢板 A517/A517M-93(1999) 压力容器用经回火与淬火的高强度合金钢板 A518/A518M-99 耐蚀高硅铁铸件 A519-96 无缝碳素钢与合金钢机械管 A521-96 一般工业用闭式模钢锻件 A522/A522M-95b(2000) 低温用锻制或轧制含镍 8%和 9%的合金钢法兰,配件,阀门和零件规格 A523-96 高压管型电缆线路用平端无缝与电阻焊钢管 A524-96 常温和低温用无缝碳素钢管 A529/A529M-00 高强度碳锰结构钢质量 A530/A530M-99e1 特种碳素钢和合金钢管 A531/A531M-91(1996) 涡轮发电机钢定位环的超声波检验 A532/A532M-93a(1999)e1 耐磨铸铁 A533/A533M-93(1999) 压力容器用经回火和淬火的锰钼及锰钼镍合金钢板 A534-94 用于耐摩擦轴承的渗碳钢 A536-84(1999)e1 球墨铸铁件 A537/A537M-95(2000) 压力容器用经热处理的碳锰硅钢板 A53/A53M-01 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范 A539-99 天然气和燃料油管线用电阻焊钢盘管 A540/A540M-00 特殊用途的合金钢螺栓材料

A541/A541M-95(1999) 压力容器部件用经淬火和回火的碳素钢及合金钢锻件 A542/A542M-99e1 压力容器用经回火和淬火的铬钼、铬钼钒及铬钼钒钛硼合金钢板 A543/A543M-93(1999) 压力容器用经回火和淬火的镍铬钼合金钢板 A550-78(2000) 铌铁合金 A551-94(1999) 钢轮箍 A553/A553M-95(2000) 压力容器用经回火和淬火的含 8%及 9%镍的合金钢板 A554-98e1 焊接的无缝钢机械管 A555/A555M-97 耐热不锈钢丝和盘条的通用要求 A556/A556M-96 无缝冷拉碳素钢给水加热器管 A560/A560M-93(1998) 铬镍合金铸件 A561-71(1999) 工具钢棒的宏观刻蚀试验 A562/A562M-90(2001) 搪玻璃或扩散金属镀层的压力容器用锰钛合金碳素钢板 A563-00 碳合金钢螺母 ASTM 钢管标准 3 A563M-00 碳素钢及合金钢螺母技术规范(米制) A564/A564M-01 热轧及冷精轧时效硬化处理过的不锈钢棒材和型材技术规范 A565-97 高温用马氏体不锈钢棒,锻件和锻制坯规格 A568/A568M-00b 热轧及冷轧高强度低合金碳素钢薄板 A571-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件 A571M-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件(米制) A572/A572M-00a 高强度低合金钴钒结构钢技术规范 A573/A573M-00a 增强韧性的结构碳素钢板 A574-00 合金钢内六角螺钉 A574M-00 合金钢内六角螺钉(米制) A575-96 商品级碳素钢棒(M 级) A576-90b(2000) 特级热轧碳素钢棒 A577/A577M-90(2001) 钢板的超声角波束检验 A578/A578M-96(2001) 特殊设备用的普通钢板和包覆钢板的直波束超声探伤检验 A579-99 超高强度合金钢锻件 A580/A580M-98 耐热不锈钢丝 A581/A581M-95b(2000) 高速切削用耐热不锈钢丝和盘条 A582/A582M-95b(2000) 热轧或冷精轧的高速切削不锈及耐热钢棒 A583-93(1999) 铁路用铸钢轮 A584-97 镀铝钢丝编织栅栏网 A585-97 镀铝刺钢丝 A586-98 镀锌平行和螺旋形钢丝绳 A587-96 化学工业用电阻焊低碳钢管 A588/A588M-00a 高强度低合金结构钢 4 英寸(100mm)厚屈服点最小为 50ksi(345MPa) A589-96 水井用无缝和焊接碳素钢管 A591/A591M-98 薄镀层电解镀锌薄钢板 A592/A592M-89(1999) 压力容器用经回火和淬火的高强度低合金钢锻制附件和零件 A595-98 结构用圆锥形低碳钢管 A596/A596M-95(1999) 用环形试验法和冲击法测定材料的直流磁性能的试验方法 A597-87(1999) 铸造工具钢

A598-92(1997) 磁放大器磁芯的磁性能测试法 A599/A599M-99 锡制品,电解镀锡的冷滚轧薄板规范 A6/A6M-01 轧制结构钢板材、型材和薄板桩通用技术要求 A600-92a(1999) 高速工具钢 A601-96(2000) 电解金属锰 A602-94(1998) 汽车用可锻铸铁件 A603-98 镀锌结构钢丝绳 A604-93(1998) 自耗电极再溶化钢棒与钢坯的宏观腐蚀试验方法 A606-98 改进防大气腐蚀性的热轧和冷轧高强度低合金钢薄板和带材 A608-91a(1998) 高温受压离心铸造的铁铬镍高合金钢管 A609/A609M-91(1997) 碳素钢,低合金钢和马氏体不锈钢铸件的超声波检测 A610-79(2000) 尺寸测量用铁合金的取样和试验 A611-00 冷轧优质碳素结构钢薄板 A612/A612M-00 中温和低温压力容器用高强度碳素钢板 A615/A615M-01a 钢筋混凝土配筋用变形和光面坯钢筋 A618-01 热成型焊接与无缝高强度低合金结构钢管系 A623-00 锡轧制产品 A623M-00 镀锡薄钢板轧制品通用要求(米制) A624/A624M-98 锡辊轧制品.单压延电解马口铁 A625/625M-98 一次轧制原钢板(未镀)和镀锡薄钢板轧制产品技术规范 A626/A626M-98 二次压延电解镀锡厚钢板轧制品技术规范 A626/A626M-98 锡轧制品.二次压延的电解镀锡板(米制) A627-95 安全设备用均质不易加工的钢棒 A629-88(1994)e1 安全设备用不易加工的扁钢棒和型材 A630-98 热浸电解镀锡板镀锡层重量测定的方法 A632-01 通用无缝和焊接奥氏体不锈钢管(小直径) A633/A633M-00a 正火的高强度低合金结构钢 A635/A635M-00 热轧碳素钢薄板,带材和重型粗盘条规格 A636-76(2000) 氧化镍烧结块 A638/A638M-00 高温用沉积硬化铁基超级合金棒,锻件及锻坯料 A640-97 8 字型缆吊架用镀锌钢丝绳 A641/A641M-98 镀锌(电镀)碳素钢丝技术规范 A644-98 铁铸件的相关术语 A645/A645M-99a 压力容器用经特殊热处理的 5%镍合金钢板 A646-95(1999) 飞机及航空器锻件用优质合金钢大方坯及坯段 A648-95(2000) 预应力混凝土管用冷拉钢丝 A649/A649M-99 波纹纸机械用锻制钢辊规格 A650/A650M-98 二次压延的锡轧黑板材 A653/A653M-00 热浸处理的镀锌铁合金或镀锌合金薄钢板的标准规范 A656/A656M-00a 具有改良可模锻性的高强度低合金热轧结构钢板 A657/A657M-98a 一次和二次压延电解镀铬黑钢板轧制品技术规范 A65-01 钢轨道钉 A659/A659M-97 商业级热轧碳素钢薄板和带材(最大含碳量为 0.16%-0.25%) A660-96 高温用离心铸造碳素钢管

A662/A662M-99 中温和低温压力容器用锰碳钢板规格 A663/A663M-89(2000) 商品级碳素钢棒的机械特性 A664-99 在 ASTM 规范中对电工钢和层压钢级别的识别 A666-00 退火或冷加工的奥氏体不锈钢薄板、带材、中厚板和扁棒 A667/A667M-87(1998) 离心铸造的双金属(灰口及白口铸铁)圆柱体 A668/A668M-96e1 一般工业用碳素钢和合金钢锻件 A66-01 钢质螺旋道钉 A671-96 常温和较低温用电熔焊钢管 A672-96 中温高压用电熔焊钢管 A673/A673M-95 结构钢冲击试验的取样程序 A674-00 水或其它液体用球墨铸铁管的聚乙烯包装 A675/A675M-90a(2000) 专用热轧碳素钢棒的机械特性 A677/A677M-99 全处理型无取向电工钢 A678/A678M-00a 结构用经回火和淬火的高强度低合金碳素钢板规格 A679/A679M-00 硬(冷)拉高抗拉强度钢丝 A67-00 热加工低碳钢和高碳钢垫板技术规范 A681-94(1999) 合金工具钢 A682/A682M-00 弹簧用冷轧高碳钢带材 A683/A683M-99 半处理型无取向电工钢 A684/A684M-99 冷轧高碳钢带材 A686-92(1999) 碳素工具钢 A688/A688M-01 焊接的奥氏体不锈钢给水加热器管 A689-97 弹簧用碳素钢及合金钢棒 A690/A690M-00a 在海洋环境中使用的高强度低合金工字形钢桩和薄板桩规格 A691-98 高温下高压装置用电熔焊碳素钢和合金钢管 A693-93(1999) 沉淀硬化耐热不锈钢板、薄板和带材 A694/A694M-00 高压传输设备用碳素钢及合金钢管法兰、配件、阀门及零件用锻件 A695-90b(1995)e1 流体动力设备专用热锻碳素钢棒 A696-90a(2000) 压力管道部件专用热锻或冷精轧碳素钢棒 A697-98 用伏特计、安培计和瓦特计法测定迭层铁芯样品的交流磁特性的试验方法 A698/A698M-92(1997)e1 在弱交流磁场中磁屏蔽效率的试验方法 A700-99e1 钢制品国内装运的包装、标记和装载方法 A701-96(2000) 硅锰铁 A702-89(2000) 热锻钢栅栏柱和组件 A703/A703M-01 受压部件用钢铸件 A704/A704M-96 混凝土加筋用焊接普通钢棒或杆的光面钢筋或钢筋网 A705/A705M-95(2000) 时效硬化的不锈和耐热钢锻件 A706/A706M-01 混凝土配筋用变形低合金光面无节钢筋 A707/A707M-00a 低温设备用锻制碳素钢和合金钢法兰 A709/A709M-01 桥梁用结构钢 A710/A710M-00 低碳时效硬化的镍铜铬钼铌合金钢 A711-92(1996)e1 钢锻件坯料 A712-97 软磁性合金电阻率的测试方法 A713-93(1998) 热处理部件用高碳弹簧钢丝

A714-99 高强度低合金焊接钢管和无缝钢管 A716-99 球墨铸铁涵洞管 A717/A717M-95 单片样品表面绝缘电阻率的试验方法 A719-97 磁性材料的叠装系数的试验方法 A720-97 无取向电工钢延展性的试验方法 A721-97 取向的电工钢的延展性试验方法 A722/A722M-98 预应力混凝土用无涂覆的高强度钢筋 A723/A723M-94(1999) 高强度压力元件用合金钢锻件 A724/A724M-99 叠层焊接的压力容器用经淬火及回火的碳素钢压力容器板 A726-00 半成品型冷轧磁性迭片级钢 A727/A727M-00 具有固定切口韧性的管道部件用碳素钢锻件 A729-93(1999) 货物运输及电气铁路用热处理合金钢轴 A730-93(1999) 铁路用碳素钢及合金钢锻件 A732/A732M-98 一般设备用熔模铸造碳素低合金钢及高强度加温钴合金钢铸件 A733-99 焊接及无缝碳素钢和奥氏体不锈钢管接头 A734/A734M-87a(1997) 经淬火和回火的合金钢与高强度低合金钢压力容器板 A735/A735M-99 中温和低温用低碳锰钼钶合金钢压力容器板 A736/A736M-88(2000) 低碳时效硬化的镍铜铬钼铌和镍铜锰钼铌合金钢压力容器板 A737/A737M-99 高强度低合金钢压力容器板 A738/A738M-00 中温和低温设备用经热处理的碳锰硅钢压力容器板 A739-90a(2000) 升温或/和加压部件用热轧合金钢棒 A740-98 钢丝网(编织或焊接电镀钢丝网) A741-98 公路护栏用镀锌钢丝绳和配件 A742/A742M-98 波纹钢管用预涂聚合物和金属涂覆钢薄板 A743/A743M-98ae1 一般用耐腐蚀铬铁及镍铬铁合金铸件 A744/A744M-00 严酷条件下使用的耐腐蚀镍铬铁合金铸件 A745/A745M-94(1999) 奥氏体钢锻件的超声波检验 A746-99 排污管用球墨铸铁 A747/A747M-99 沉淀硬化不锈钢铸件 A748/A748M-87(1998) 压力容器用静态铸造的激冷白口铁-灰口铁双金属轧辊 A749/A749M-97 热轧碳素钢和高强度低合金钢带材通用要求 A74-98 铸铁污水管及配件的技术规范 A750-77(1994)e1 阻挡区域用钢制通风格栅 A751-96 钢制品化学分析的实验方法、操作和术语 A752-93(1998) 合金钢条和粗圆钢丝 A752M-93(1998) 合金钢条和粗圆钢丝(米制) A753-97 镍铁软磁合金 A754/A754M-96(2000) X 射线荧光涂层厚度的试验方法 A755/A755M-99 外露建筑材料用热浸涂覆和用卷涂工艺预涂的钢薄板 A756-94(2001) 耐磨不锈轴承钢 A757/A757M-00 低温下承压设备及其它设备用铁素体和马氏体钢铸件 A758/A758M-00 具有改进的切口韧性的对缝焊锻制碳素钢管配件 A759-00 起重机用碳钢轨条 A760/A760M-01 下水道和排水沟用金属涂覆的波纹钢管

A761/A761M-98 现场栓接管、管拱和拱用波纹镀锌结构钢板 A762/A762M-00 下水道和排水沟用预涂聚合物波纹钢管 A763-93(1999)e1 铁素体不锈钢晶间腐蚀敏感性检测 A764-95(2001) 机械弹簧用冷拉镀锌和按成品尺寸镀锌的碳素钢丝 A765/A765M-98a 具有强制性韧性要求的碳素钢及低合金钢压力容器部件锻件 A767/A767M-00b 钢筋混凝土用镀锌钢筋 A768-95 涡轮机转子及轴用经真空处理的含铬 12%的合金钢锻件 A769/A769M-00 电阻焊钢结构型材 A770/A770M-86(2001) 专用钢板通过厚度测量进行的抗拉试验 A771/A771M-95(2001) 增殖反应堆堆芯部件用奥氏体不锈钢管 A772/A772M-00 正弦电流用材料的交流磁导率的试验方法 A773/A773M-96 用带直流电子的磁滞曲线记录仪的(B-H)回路法测量材料的磁性能的标准试验方法 A774/A774M-00 低温和中温一般腐蚀情况下用的焊接锻制奥氏体不锈钢配件 A775/A775M-01 涂环氧树脂的钢筋钢棒 A778-01 焊接未退火的奥氏体不锈钢管形制品 A779/A779M-00 预应力混凝土用应力消除未涂覆的密实七股钢丝绞绳 A780-01 热浸镀锌层的损坏及无覆层区域的检修 A781/A781M-00 一般工业用一般要求的钢和合金铸件 A782/A782M-90(2001) 经淬火和回火的锰铬钼硅锆合金钢压力容器板 A786/A786M-00b 轧制钢楼板 A787-01 电阻焊金属涂覆碳素钢机械配管 A788-98a 钢锻件 A789/A789M-01 普通设备用无缝与焊接铁素体/奥氏体不锈钢管 A790/A790M-01 无缝与焊接铁素体/奥氏体不锈钢管 A792/A792M-99 热浸工艺法处理的 55%铝-锌合金涂覆钢板 A793-96 不锈钢轧制楼板 A794-97 商品级冷轧碳素钢薄板(最高含碳量为 0.16%-0.25%) A795-00 防火用黑色及热浸镀锌的焊接和无缝钢管 A796/A796M-00 雨水管和卫生污水管及其它地下埋设管道用波纹钢管、管托架及拱形架结构设计惯例 A798/A798M-01 下水道及其它类似用途用工厂制波纹钢管的安装 A799/A799M-92(1997) 估算不锈钢铸件铁素体含量用仪表的校准 A800/A800M-01 奥氏体合金钢铸件中铁素体含量的估算 A801/A801M-99 铁钴高磁性饱和合金 A802/A802M-95(2001) 钢铸件外观检验的表面验收标准 A803/A803M-01 焊接铁素体不锈钢给水加热器管 A804/A804M-99 在电力频率下用薄钢板型试样对材料交流磁特性的测试方法 A805-93(1998) 冷轧碳素钢扁平线 A807/A807M-97 下水道及其它类似用途用波纹结构钢涂覆管的安装 A808/A808M-00a 具有改进的切口韧性的结构级高强度低合金碳钢、锰钢、铌钢和钒钢 A809-98 镀铝碳素钢丝 A810-00 镀锌钢管用绕网 A811-97 粉末冶金技术制造的软磁铁零件 A813/A813M-01 单或双焊接奥氏体不锈钢管 A814/A814M-01 冷加工焊接奥氏体不锈钢管

A815/A815M-01 锻制铁素体、铁素体/奥氏体和马氏体不锈钢管配件 A817-00 链接栅栏网用金属涂覆钢丝 A818-91(2001) 镀铜碳素钢丝 A820-96 纤维增强混凝土用钢纤维 A821/A821M-99 预应力混凝土容器用经回火的冷拉钢丝 A822-90(2000) 液压系统设备用冷拉碳素无缝钢管 A823-99 静铸永久铸模灰铸件 A824-01 链接栅栏用 Marcelled 拉力金属涂覆钢丝 A826/A826M-95(2001) 增殖反应堆堆芯部件用奥氏体和铁素体不锈钢管 A827/A827M-93a(1998) 锻造及类似用途用的碳素钢板技术规范 A829/A829M-00 结构性合金钢板 A82-97ae1 钢筋混凝土用无节钢丝 A830/A830M-00 按照化学成分要求提供的优质碳素钢板技术规范 A831/A831M-95(2000) 核心部件用不锈耐热钢棒,坯段及锻件规格 A832/A832M-99e1 压力容器板用铬钼钒及铬钼钒钛硼合金钢 A833-84(1996) 用比较硬度测试仪测量金属材料的压痕硬性 A834-95(2001) 一般工业用铁铸件的一般要求 A835-84(2000) 铁合金与合金添加剂的筛分粒度 A836/A836M-95b(2001) 搪瓷管和压力容器设备用钛稳定碳素体钢锻件 A837-91(1996)e1 渗碳用合金钢锻件 A838/A838M-97 继电器用易切削铁素体不锈软磁合金技术规范 A839/A839M-96 软磁用途的磷铁粉末冶金制造的零件技术规范 A840/A840M-00 全处理的磁性夹层钢 A841/A841M-01 压力容器用温度机械控制工艺加工的钢板 A842-85(1997) 高密度石墨铸铁 A844/A844M-93(1999) 压力容器用直接淬火加工的含镍 9%的合金钢板 A845-85(2000) 用于脱氧与合金钢的钛碎片 A846-85(2000) 用于脱氧与合金钢的铝碎片 A847-99a 具有增强耐大气腐蚀性能的冷成型焊接与无缝高强度低合金结构管 A848/A848M-96 低碳磁铁 A849-00 波纹钢排水管和污水管用后涂覆铺面和衬里材料 A851-96 高频感应焊接的未退火奥氏体钢冷凝器管 A852/A852M-00a 最小屈服强度为 70Ksi(485MPa),厚度为 4 英寸(100mm)的经淬火和回火的低合金结构钢板 ASTM 钢管标准 4 A853-93(1998) 普通碳素钢丝 A854/A854M-98 镀锌高强度钢栅栏和格架用光滑金属线 A855/A855M-98 锌-5%铝-铈合金涂覆的钢丝绳 A856/A856M-98 锌-5%铝-铈合金涂覆的碳素钢丝 A857/A857M-00a 冷成形轻型薄钢板桩 A858/A858M-00 低温和腐蚀情况下用热处理碳素钢配件 A859/A859M-95(1999) 压力容器部件用时效硬化镍铜铬钼钶低碳合金钢锻件 A860/A860M-00 锻制高强度低合金钢的高强度对缝焊接配件 A861-94e1 高硅铁管和配件 A862/A862M-98 波纹钢污水管和排水管沥清(柏油)涂层的应用

A865-97 钢管连接用黑色或镀锌焊接或无缝钢螺纹接头 A866-94 耐磨中碳轴承钢 A867/A867M-94(1998)e1 继电器用铁硅钢 A871/A871M-00a 抗空气腐蚀的高强度低合金结构钢板 A872-91(1997) 腐蚀环境下用离心铸造铁素体/奥氏体不锈钢管 A874/A874M-98 适于低温使用的铁素体球墨铸铁铸件 A875/A875M-01 热浸处理的锌-5%铝合金金属涂覆的钢薄板 A876/A876M-98 全处理型平轧的晶粒取向的硅铁电工钢 A877/A877M-99 铬硅合金阀弹簧级钢丝 A878/A878M-99 经改良的铬钒阀弹簧级钢丝 A879-00 每面镀层质量应予标明的电解镀锌薄钢板 A880-95 评定钢、不锈钢及相关合金检验与测验组织和实验室的准则 A881/A881M-99 预应力混凝土铁路轨枕用应力消除或应力松弛变形钢丝 A882/A882M-96e1 涂环氧树脂的七股预应力钢丝绳 A883-96 非金属磁性材料铁磁共振行距和旋磁比率的测试方法 A884/A884M-01 钢筋用涂环氧树脂的钢丝与焊接钢丝织网的技术规范 A885/A885M-96 波纹钢制下水沟、暗渠和雨水管用锌和聚芳基酰胺纤维复合涂覆钢板 A886/A886M-99 预应力混凝土用应力消除的七股齿纹钢丝绳 A887-89(2000) 核能设备用经硼酸处理的不锈钢板、薄板及带材 A888-98e1 下水管、雨水管、污水管和排气管道用无衬套铸铁管和配件 A889/A889M-93(1998) 在低感应条件下用万用表法和 25 厘米艾普斯亭(Epstein)框测定材料的交流磁特性的试 验方法 A890/A890M-99 普通应用的铁铬镍钼耐腐蚀双重(奥氏体/铁素体)铸件 A891-98 涡轮机转子圆盘和轮用沉淀硬化铁基超合金钢锻件 A892-88(2001) 高碳轴承钢微观结构的定义和等级 A893-97 微波频率下非金属磁性材料复合介电常数的测试方法 A894/A894M-00 非金磁性材料的饱和磁化强度或磁感应性能的标准试验方法 A895-89(2000) 易切削不锈钢板、薄板和带材 A896-89(1999) 电镀结构导电壳的研究 A897-90(1997) 等温淬火球墨铸铁 A897M-90(1997) 等温淬火球墨铸铁(米制) A898/A898M-91(1996) 轧制结构钢型材的直束超声检验 A899-91(1996) 环氧涂层钢丝 A90/A90M-01 镀锌和镀锌合金钢铁制品镀层重量的试验方法 A900-91(1996)e1 非晶磁性带材叠装系数的测试方法 A901-97 半成品型非晶形磁芯合金 A902-99 与金属涂覆的钢制品有关的标准技术术语 A903/A903M-97 钢铸件磁粉探伤和荧光渗透检验的表面验收标准 A904-98 50 镍-50 铁粉末冶金(P/M)软磁合金 A905-93(1998) 压力容器缠绕用钢丝 A906/A906M-99 高架提升设备用的 80 级和 100 级合金钢悬链规范 A907/A907M-96 结构级热轧碳素钢薄板、带材及特厚型卷材 A908-91(1998) 不锈钢针管 A909-94(1999) 一般企业用微合金钢锻件

A910/A910M-99 预应力混凝土用无涂层、无焊缝、2 股及 3 股钢绞绳 A911/A911M-99 预应力混凝土轨枕用无涂层的预应力消除的钢棒 A912-93(1998) 用万用表环形样品法测试非晶材料在电频率条件下交流磁特性的试验方法 A913/A913M-00a 经淬火和自回火(QST)处理的高强度低合金结构级钢型材 A914/A914M-92(1999) 对末端淬火淬透性有限制要求的钢棒材技术规范 A915/A915M-93(1998) 化学要求同锻件类似的碳素钢和合金钢 A917-00 要求每一面标识有镀层质量用的电解工艺涂层的薄钢板材标准规范 A918-00 要求在每一面标识有涂层质量用电解工艺镀锌镍合金的薄钢板技术规范 A920/A920M-97 具有机械特性,微合金,热锻,高质量钢棒的标准规范 A921/A921M-93(1999) 后热锻用微合金,高质量,热锻钢棒的标准规范 A922-93(2000) 硅金属标准规范 A923-98 检测锻制双重奥氏体/铁素体不锈钢中有害金属间相的标准试验方法 A924/A924M-99 用热浸镀法对薄钢板金属涂层的一般要求的标准规范 A925-98 锌-5%铝.混合稀土合金涂覆钢的地面金属绞线的技术规范 A926-97 波纹形金属管用比较涂层材料磨损阻力的标准测试方法 A927/A927M-99 使用伏特计-电流计-瓦特计方法的环形铁芯交流磁性能的标准试验方法 A928/A928M-00 加填料金属电熔焊铁素体/奥氏体(二联)不锈钢管标准规范 A929/A929M-01 波纹钢管用的经热浸处理的金属镀覆薄钢板标准规范 A930-99 涵洞,暴雨下水道和其它地下的排水道用波形金属管的寿命周期费用分析的标准惯例 A931-96 金属丝绳和绞线拉伸试验的标准试验方法 A932/A932M-95 用瓦特计-安培计-伏特计和薄钢板样品测试在电源频率下非晶体材料交流磁性能的标准试验方 法 A933/A933M-95(2001) 加筋增强用聚氯乙烯涂层钢丝和焊接钢丝网的标准规范 A934/A934M-01 环氧基树脂涂覆的预制增强钢棒的标准规范 A935/A935M-97a 热轧铌或钒,或铌钒低合金高强度薄钢板、带材技术规范 A936/A936M-97a 热轧制,可模锻性得到加强的低合金、高强度薄板钢材、带材技术规范 A937-95 使用临界试验面测定绝缘涂层层间阻力的标准测试方法 A938-97 丝材抗扭试验的标准试验方法 A939-96 圆柱体锻件镗孔表面反射超声检测的标准试验方法 A940-96 涡轮转子用的差温热处理真空处理钢锻件,合金钢锻件的标准规范 A941-00a 钢,不锈钢,有关合金和铁合金术语 A942-95(2001) 离心铸造白口铁/灰口铁双金属耐磨滚轮外壳标准规范 A943/A943M-01 喷模制无缝奥氏体不锈钢管的技术规范 A944-99 用梁端试样与混凝土比较的钢筋棒结合强度标准试验方法 A945/A945M-00 为改良可焊接性、可加工性及粘接性用低碳限硫的高强度低合金结构钢板的标准规范 A946-95(2000) 耐腐蚀和耐热用铬,铬-镍和硅合金钢板,薄板和带的标准规范 A947M-95(2000) 织构化不锈钢薄板的标准规范 A949/A949M-01 喷模制无缝铁素体/奥氏体不锈钢管的标准规范 A950/A950M-99 涂有熔融胶接环氧树脂的结构钢 H 型钢桩和薄板桩技术规范 A951-00 砌体接缝配筋的技术规范 A952/A952M-98 锻制 80 号和 100 号钢提升元件和焊接联接杆技术规范 A952/A952M-98 锻制 80 级合金钢提升元件和焊接的附加链接件的标准规范 A953-96 奥氏体铬镍硅合金钢无缝和焊接管件的标准规范 A954-96 奥氏体铬镍硅合金钢无缝和焊接管的标准规范

A955/A955M-01 混凝土增强的变形的和无节钢筋技术规范 A956-00 钢制品依阔提皮(Equotip)硬度测试方法 A957-96 一般工业用普通要求熔模铸造的钢及合金钢熔模铸件技术规范 A958-00 拉伸要求及化学要求类似于标准铸造等级的碳钢和合金钢铸件的技术规范 A959-00a 锻制不锈钢用说明协调标准等级构成的标准指南 A960-00 普通要求的锻制钢管管件的标准规范 A961-01 管路用钢法兰盘,锻制管接头,阀门和零件的通用要求规范 A962/A962M-01 预定用于从低温至蠕变范围内任何温度的钢紧固件或其材料的通用要求 A964/A964M-96 波纹钢箱形涵洞规范 A965/A965M-01 压力和高温零件用奥氏体钢锻件的技术规范 A966/A966M-96 用交流电和磁粉探伤检验钢锻件的标准试验方法 A967-99e1 不锈钢零件的化学钝化处理的技术规范 A968-96 和耐热耐蚀设备用铬,铬镍及硅合金钢棒材及型材的技术规范 A970/A970M-98 混凝土配筋用焊接或锻制镦头的棒材技术规范 A971-00 测量扁平轧制的钢盘条轧边锥(斜)度和凸度的标准试验方法 A972/A972M-00 熔焊的环氧树脂涂层的管桩规范 A973/A973M-00 100 级的合金钢链条规范 A974-97 焊线纤维金属筐和金属丝网的标准规范.(金属涂层或聚氯乙烯(PVC)涂层) A975-97 双层和扭转网眼金属筐和护墙垫金属和涂层钢线或聚氯乙烯(PVC)金属涂层钢线 A976-97 按照成份、相对绝缘能力及用途对绝缘涂层进行分类方法 A977-97 用磁滞曲线图测定高矫顽力永久磁性材料磁性的标准试验方法 A978/A978M-97 重力流动卫生用排污管道, 暴雨排污管道用和其他专用的预涂层的和聚乙烯衬料带由复合材料加 强肋的钢管规范 A979/A979M-97 外场用波纹钢结构件中填装的混凝土铺料和衬料规范 A980-97 冷轧超高强度碳素钢薄钢板技术规范 A981-97 评定加预应力地锚使用的 270 号、直径为 15.2 毫米(0.6 英寸)加预应力连铸钢坯结合强度的标准试验 方法 A982-00 涡轮叶片用不锈钢锻件技术规范 A983/A983M-98 中速柴油发动机用连续晶粒流向锻制的碳素钢及合金钢曲轴技术规范 A984/A984M-00 电阻焊焊接的平滑端黑钢管技术规范 A985-98a 容压件使用的熔模钢铸件通用技术要求 A986/A9786M-98 连续晶粒流向曲轴锻件的磁粉探伤检查技术规范 A986/A986M-98 连续晶体流向曲轴锻件的磁粉检验的标准试验方法 A987-00 镀锡薄钢板轧制产品形状特性测量的标准试验方法 A988-98 高温下使用的热等静加压成形的不锈钢法兰盘、管配件、阀及零件的技术规范 A989-98 高温下使用的热等静加压成形的合金钢法兰盘、管配件、阀及零件的技术规范 A990-00 耐腐用保压零件用特殊控制阀的铁铬镍和铬合金铸件技术规范 A991/A991M-98 钢制品热处理炉温度均匀度测量标准试验方法 A992/A992M-00 建筑框架中使用的结构成型件钢规范 A993-98 铸铁的动扯裂试验到确定传递温度的标准试验方法 A994-98 钢,不锈钢及相关合金的产品规范编辑程序和格式指南 A995-98 容压件用奥氏体-铁素体(用二联法)不锈钢铸件技术规范 A996/A996M-01 混凝土用条钢和车轴钢 变形钢棒规范 A997-98 熔模铸件目视检查表面验收标准的标准惯例

A99-82(2000) 锰铁合金 A999/A999M-01 合金钢和不锈钢管通用要求规范

2006

2007-03-25 19:12

查看标准目录网,ASTM、ASME、SH、GB、HG 等标准目录应由尽有!!

2006

2007-03-25 20:16

ASME PCC-1 Guidelines for Pressure Boundary Bolted Flange Joint Assembly ASME B107.52M Nail-Puller Bars: Safety Requirements ASME B30.6 INTERPRETATIONS Interpretations to B30.6-1995 Derricks ASME B30.17A Addenda to B30.17-1998 Overhead and Gantry Cranes (Top Running Bridge, Single Girder, Underhung Hoist) ASME B40.200 Thermometers, Direct Reading and Remote Reading Incorporating ASME B40.3, B40.4, and B40.9; Replaces ASME B40.3:1997 ASME B18.8.100M Spring Pins: Coiled Type, Spring Pins: Slotted, Machine Dowel Pins: Hardened Ground, and Grooved Pins Metric Series; Incorporating ASME B18.8.3M, B18.8.4M, B18.8.5M, and B18.8.9M ASME B56.1 INTERPRETATIONS Interpretations to B56.1-1993 Safety Standard for Low Lift and High Lift Trucks ASME AG-1A Addenda to ASME AG-1-1997 Code on Nuclear Air and Gas Treatment ASME B30.1A Addenda to B30.1-1998 Jacks ASME PVHO-1B Addenda to Asme PVHO-1-1997 Safety Standard for Pressure Vessels for Human Occupancy ASME B30.14C Addenda to B30.14-1996 Side Boom Tractors ASME B94.18 Punches - Basic Ball-Lock, Light and Heavy Duty R(2000) ASME NQA-1 INTERPRETATIONS Interpretations to NQA-1-2000 Edition Quality Assurance Requirements for Nuclear Facility Applications ASME A112.6.2 Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks ASME PTC 10 Performance Test Code on Compressors and Exhausters (Performance Test Codes) ASME B18.30.1M Open-End Blind Rivets with Break Mandrels (Metric Series) ASME B18.13A Addenda to B18.13-1996 Screw and Washer Assemblies - Sems (Inch Series) ASME B107.51 Star Drills: Safety Requirements ASME B30.6C Addenda to B30.6-1995 Derricks ASME B30.14B Addenda to B30.14-1996 Side Boom Tractors ASME BPEA Addenda to BPE-1997 Bioprocessing Equipment ASME 3977-1 Gas Turbines: Procurement Part 1: General Introdustion and Definitions ISO 3977-1:1997 ASME 3977-2 Gas Turbines: Procurement Part 2: Standard Reference Conditions and Ratings ISO 3977-2: 1997 ASME AS-11 Personnel of Codes, Standards, and Related Conformity Assessment Committees ASME B15.1 INTERPRETATION Interpretations to B15.1-2000 Safety Standard for Mechanical Power Transmission Apparatus

ASME B18.2.2 Square and Hex Nuts (Inch Series) R(1999) ASME B18.2.3.8M Metric Hex Lag Screws R(1999) ASME B18.2.3.8M ASME B18.18.1M Inspection and Quality Assurance for General Purpose Fasteners R(1999) ASME B18.18.2M Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners R(1999) ASME B18.18.3M Inspection and Quality Assurance for Special Purpose Fasteners R(1999) ASME B18.18.4M Inspection and Quality Assurance for Fasteners for Highly Specialized Engineered Applications R(1999) ASME B18.22M Metric Plain Washers R(2000) ASME B27.6 General Purpose Uniform Cross Section Spiral Retaining Rings R(1999) ASME B27.7 General Purpose Tapered and Reduced Cross Section Retaining Rings R(1999) ASME B30.19 Cableways ASME B31.1B Addenda to B31.1-1998 Edition Power Piping ASME B56.5 Safety Standard for Guided Industrial Vehicles and Automated Functions of Manned Industrial Vehicles R(2000) ASME B56.8 Safety Standard for Personnel and Burden Carriers R(2000) ASME B56.9 Safety Standard for Operator Controlled Industrial Tow Tractors R(2000) ASME B56.11.1 Double Race or Bi-Level Swivel and Rigid Industrial Casters Special Notice - October 1993 R(2000) ASME B56.11.3 Load Handling Symbols for Powered Industrial Trucks Special Notice - October 1993 R(2000) ASME B56.11.5 Measurements of Sound Emitted by Low Lift, High Lift, and Rough Terrain Powered Industrial Trucks Special Notice - October 1993 R(2000) ASME B56.11.6 Evaluation of Visibility from Powered Industrial Trucks R(2000) ASME B107.58M Riveting, Scaling, and Tinner's Setting Hammers: Safety Requirements ASME B107.58M ASME OM-S/G Standards and Guides for Operation and Maintenance of Nuclear Power Plants ASME BPV DECEMBER-2000 Companies Holding Boiler and Pressure Vessel Certificates of Authorization for Use of Code Symbol Stamps and Testing Laboratories Holding Certificates of Acceptance for Conducting Tests of Pressure Relief Devices No.62-December 2000 ASME BPV APRIL-2001 ASME PTC 12.1 Closed Feedwater Heaters ASME PTC 12.1 ASME SEC XI D1 ART IWE-5000 Article IWE-5000 System Pressure Tests ASME SEC XI D1 ART IWE-7000 Article IWE-7000 Replacements DELETED ASME A13.1 Scheme for the Identification of Piping Systems Erratum - September 1998 ASME A17.1 Safety Code for Elevators and Escalators ASME A17.1 ASME A17.1 HDBK Handbook for Safety Code for Elevators and Escalators ASME A17.1 INTERPRETATIONS Interpretations to A17.1-1996 Safety Code for Elevators and Escalators Includes Interpretations No. 1 through 22 ASME A17.1 INTERPRETATIONS ASME A17.1A Addenda to A17.1-1996 Safety Code for Elevators and Escalators

ASME A17.1B Addenda to A17.1-1996 Safety Code for Elevators and Escalators ASME A17.1C Addenda to A17.1 - 1996 Safety Code for Elevators and Escalators ASME A17.1D Addenda to Asme A17.1-1996 Safety Code for Elevators and Escalators ASME A17.2.1 Inspectors' Manual for Electric Elevators ASME A17.2.1A Addenda to A17.2.1-1996 Inspectors' Manual for Electric Elevators ASME A17.2.1B Addenda to A17.2.1-1996 Inspectors' Manual for Electric Elevators ASME A17.2.2 Inspectors' Manual for Hydraulic Elevators ASME A17.2.2A Addenda to A17.2.2-1997 Inspectors' Manual for Hydraulic Elevators ASME A17.2.3 Inspectors' Manual for Escalators and Moving Walks Includes Inspection Procedures for Escalators and Moving Walks ASME A17.2.3 INT NO 1 Interpretations No. 1 to A17.2.3-1998 Inspectors- Manual for Escalators and Moving Walks ASME A17.2.3A Addenda to ASME A17.2.3-1998 Inspectors' Manual for Escalators and Moving Walks ASME A17.3 Safety Code for Existing Elevators and Escalators ASME A17.3 INTERPRETATIONS Interpretations to A17.3-1996 Safety Code for Existing Elevators and Escalators Includes Interpretations No. 1 Through 4 ASME A17.3A Addenda to ASME A17.3-1996 Safety Code for Existing Elevators and Escalators ASME A17.4 Guide for Emergency Personnel (Includes Evacuation Procedures and Firefighters' Service Operating Procedures) ASME A17.5 Elevator and Escalator Electrical Equipment CAN/CSA-B44.1-1996 ASME A18.1 Safety Standard for Platform Lifts and Stairway Chairlifts Special Notice - 1999 ASME A90.1 Safety Standard for Belt Manlifts ASME A90.1 INTERPRETATIONS Interpretations to ASME A90.1-1997 ASME A90.1A Addenda to ASME A90.1-1997 Safety Standard for Belt Manlifts ASME A90.1B (Pending) Addenda to ASME A90.1-1997 Safety Standard for Belt Manlifts Comment Period Ends: 2000-09-12 ASME A112.1.2 Air Gaps in Plumbing Systems R(1998) ASME A112.1.3 Air Gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances ASME A112.3.1 Performance Standard and Installation Procedures for Stainless Steel Drainage Systems for Sanitary, Storm, and Chemical Applications, Above and Below Ground ASME A112.3.4 Macerating Toilet Systems and Related Components ASME A112.4.1 Water Heater Relief Valve Drain Tubes R(1998) ASME A112.4.3 Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System ASME A112.6.1M Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use ASME A112.6.7 (Pending) Enameled and Epoxy Coated Cast Iron and PVC Platic Sanitary Floor Sinks Comment Period Ends: 2000-09-26 ASME A112.14.1 Backwater Valves R(1998) ASME A112.18.1 Plumbing Fixture Fittings ASME A112.18.3 (Pending) Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings Comment Period Ends: 2000-09-26 ASME A112.18.3M Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings ASME A112.18.6 Flexible Water Connectors ASME A112.18.7 Deck Mounted Bath/Shower Transfer Valves with Integral Backflow Protection

ASME A112.19.1M Enameled Cast Iron Plumbing Fixtures Errata - November 1996; Supplement 2 June 2000 R(1999) ASME A112.19.2M Vitreous China Plumbing Fixtures Supplement 1 - June 2000 ASME A112.19.3M Stainless Steel Plumbing Fixtures (Designed for Residential Use) Revision of ANSI A112.19.3-1976 R(1996) ASME A112.19.3 ASME A112.19.4M Porcelain Enameled Formed Steel Plumbing Fixtures Errata - November 1996; Supplement 1 - 1998; Supplement 2 - June 2000 R(1999) ASME A112.19.5 Trim for Water-Closet Bowls, Tanks, and Urinals ASME A112.19.6 Hydraulic Performance Requirements for Water Closets and Urinals ASME A112.19.7M Whirlpool Bathtub Appliances ASME A112.19.8M Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, Hot Tubs, and Whirlpool Bathtub Appliances R(1996) ASME A112.19.9M Non-Vitreous Ceramic Plumbing Fixtures R(1998) ASME A112.19.10 Dual Flush Devices for Water Closets ASME A112.19.12 Wall Mounted and Pedestal Mounted, Adjustable and Pivoting Lavatory and Sink Carrier Systems Comment Period Ends: 2000-08-15 ASME A112.19.14 (Pending) Six Liter Closets Equipped with Dual Flushing Device Comment Period Ends: 2000-09-12 ASME A112.21.1M Floor Drains R(1998) ASME A112.21.2M Roof Drains Revision of ANSI A112.21.2-1971 ASME A112.21.3M Hydrants for Utility and Maintenance Use Revision of ANSI A112.21.3-1976 R(1995) ASME A112.36.2M Cleanouts R(1998) ASME A120.1 Safety Requirements for Powered Platforms for Building Maintenance ASME A120.1A Addenda to A120.1-1996 Safety Requirements for Powered Platforms for Building Maintenance ASME A120.1B Addenda to ASME A120.1-1996 Safety Requirements for Powered Platforms for Building Maintenance ASME AG-1 Code on Nuclear Air and Gas Treatment ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form) ASME B1.1 (Pending) Unified Inch Screw Threads (UN and UNR Thread Form) ASME B1.2 Gages and Gaging for Unified Inch Screw Threads Errata May 1992 R(1991) ASME B1.3M Screw Thread Gaging Systems for Dimensional Acceptability - Inch and Metric Screw Threads (UN, UNR, UNJ, M, and MJ) Errata - 1994 ASME B1.5 Acme Screw Threads ASME B1.7M Nomenclature, Definitions, and Letter Symbols for Screw Threads Revision of ANSI B1.7-1977 R(1992) ASME B1.8 Stub Acme Screw Threads R(1994) ASME B1.9 Buttress Inch Screw Threads 7 Degrees/45 Degrees Form with 0.6 Pitch Basic Height of Thread Engagement R(1992) ASME B1.10M Unified Miniature Screw Threads Errata - January 1998 ASME B1.11 Microscope Objective Thread Errata - July 1972 R(1994) ASME B1.12 Class 5 Interference-Fit Thread R(1998)

ASME B1.13M Metric Screw Threads - M Profile ASME B1.15 Unified Inch Screw Threads (UNJ Thread Form) Errata - March 1997 ASME B1.16M Gages and Gaging for Metric M Screw Threads Revision of ANSI B1.16-1972 R(1992) ASME B1.20.1 Pipe Threads, General Purpose (Inch) Revision and Redesignation of ASME/ANSI B2.1-1968 R(1992) ASME B1.20.3 Dryseal Pipe Threads (Inch) Revision and Redesignation of B2.2-1968 R(1998) ASME B1.20.5 Gaging for Dryseal Pipe Threads (Inch) R(1998) ASME B1.20.7 Hose Coupling Screw Threads (Inch) R(1998) ASME B1.21M Metric Screw Threads: MJ Profile ASME B1.22M Gages and Gaging for MJ Series Metric Screw Threads Revision of ANSI B1.22-1978 R(1992) ASME B1.30M Screw Threads - Standard Practice for Calculating and Rounding Dimensions ASME B1 TECH REPT Measurement Uncertainty for 60 Deg. Screw Thread Gage Element Measurement (Inch and Metric) ASME B4.1 Preferred Limits and Fits for Cylindrical Parts R(1999) ASME B4.2 Preferred Metric Limits and Fits R(1999) ASME B4.3 General Tolerances for Metric Dimensioned Products R(1999) ASME B5.1M T-Slots, Their Bolts, Nuts, and Tongues Revision of ANSI B5.1-1975; Should Be Used Instead of ANSI B5.1. Which Was Cancelled in 1985 ASME B5.1M ASME B5.5 Rotating Air Cylinders and Adapters One of a Series of Standards for Small Tools and Machine Tool Elements R(1998) ASME B5.8 Chucks and Chuck Jaws R(1994) ASME B5.8 (Pending) Chucks and Chuck Jaws Comment Period Ends: 2000-09-12 ASME B5.9 Spindle Noses for Tool Room Lathes, Engine Lathes, Turret Lathes, and Automatic Lathes R(1998) ASME B5.10 Machine Tapers ASME B5.11 Spindle Noses and Adjustable Adapters for Multiple Spindle Drilling Heads One of a Series of Standards for Small Tools and Machine Tool Elements R(1994) ASME B5.16 Accuracy of Engine and Tool Room Lathes One of a Series of Standards for Small Tools and Machine Tool Elements R(1992) ASME B5.18 Spindle Noses and Tool Shanks for Milling Machines R(1998) ASME B5.25 Punch and Die Sets R(1992) ASME B5.25M Punch and Die Sets (Metric) R(1992) ASME B5.28 Mounting Dimensions of Lubricating and Coolant Pumps for Machine Tools R(1994) ASME B5.32 Grinding Machines, Surface, Reciprocating Table - Horizontal Spindle R(1994) ASME B5.32.1 Grinding Machines, Surface, Reciprocating Table - Vertical Spindle R(1994) ASME B5.33 External Cylindrical Grinding Machines - Plain R(1994) ASME B5.35 Machine Mounting Specifications for Abrasive Discs and Plate Mounted Wheels Errata October 1985 R(1994) ASME B5.37 External Cylindrical Grinding Machines - Centerless R(1994) ASME B5.40 Spindle Noses and Tool Shanks for Horizontal Boring Machines R(1991) ASME B5.42 External Cylindrical Grinding Machines - Universal R(1994) ASME B5.43 Modular Machine Tool Standards R(1994)

ASME B5.43M Modular Machine Tool Standards (Metric) R(1994) ASME B5.44 Rotary Table Surface Grinding Machines R(1998) ASME B5.45 Milling Machines R(1998) ASME B5.46 Symbols for Machine Tool Indicator Plates R(1994) ASME B5.47 Milling Machine Arbor Assemblies R(1991) ASME B5.48 Ball Screws Errata - March 1979 R(1994) ASME B5.49 Glossary of Power Press Terms ASME B5.50 "V" Flange Tool Shanks for Machining Centers with Automatic Tool Changers Errata February 1995 ASME B5.51M Preferred SI Units for Machine Tools R(1994) ASME B5.52M Mechanical Power Presses General Purpose Single Point, GAP Type (Metric) R(1994) ASME B5.53M Cutter and Tool Grinding Machines R(1994) ASME B5.54 Methods for Performance Evaluation of Computer Numerically Controlled Machining Centers Errata - 1993 R(1998) ASME B5.55M Specification and Performance Standard, Power Press Brakes ASME B5.56M Specification and Performance Standard, Power Shears ASME B5.57 Methods for Performance Evaluation of Computer Numerically Controlled Lathes and Turning Centers ASME B15.1 Safety Standard for Mechanical Power Transmission Apparatus ASME B16.1 Cast Iron Pipe Flanges and Flanged Fittings Classes 25, 125, and 250 ASME B16.3 Malleable Iron Threaded Fittings Classes 150 and 300 ASME B16.4 Gray Iron Threaded Fittings - Classes 125 and 250 ASME B16.4 INTERPRETATIONS Interpretations to B16.4-1998 - Gray Iron Threaded Fittings - Classes 125 and 250 ASME B16.5 Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24 ASME B16.5 INTERPRETATIONS Interpretations to B16.5-1996 Pipe Flanges and Flanged Fittings Includes Interpretation No. 3 ASME B16.5A Addenda to B16.5-1996 Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24 ASME B16.9 Factory-Made Wrought Steel Buttwelding Fittings ASME B16.9 INTERPRETATIONS Interpretations to B16.9-1993 Factory-Made Wrought Steel Buttwelding Fittings Includes Interpretation No. 1 ASME B16.10 Face-to-Face and End-to-End Dimensions of Valves ASME B16.10 INTERPRETATIONS Interpretations to B16.10-1992 Face-to-Face and End-to-End Dimensions of Valves Includes Interpretation No. 1 ASME B16.11 Forged Fittings, Socket-Welding and Threaded ASME B16.12 Cast Iron Threaded Drainage Fittings ASME B16.14 Ferrous Pipe Plugs, Bushings, and Locknuts with Pipe Threads ASME B16.15 Cast Bronze Threaded Fittings Classes 125 and 250 R(1994) ASME B16.15 INTERPRETATIONS Interpretations to B16.5-1985 Cast Bronze Threaded Fittings Classes 125 and 250 Includes Interpretations No. 1 ASME B16.18 Cast Copper Alloy Solder Joint Pressure Fittings R(1994) ASME B16.20 Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral-Wound, and Jacketed ASME B16.20A Addenda to B16.20-1998 Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral-Wound, and Jacketed

ASME B16.20B Addenda to B16.20-1993 Metallic Gaskets for Pipe Flanges - Ring-Joint, Spiral-Wound, and Jacketed ASME B16.21 Nonmetallic Flat Gaskets for Pipe Flanges Revision of ANSI B16.21-1978 ASME B16.22 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings ASME B16.22A Addenda to B16.22-1995 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings ASME B16.23 Cast Copper Alloy Solder Joint Drainage Fittings - DWV Errata - January 1994 ASME B16.24 Cast Copper Alloy Pipe Flanges and Flanged Fittings Class 150, 300, 400, 600, 900, 1500, and 2500 Errata - 1991 R(1998) ASME B16.25 Buttwelding Ends ASME B16.25 INTERPRETATIONS Interpretations to B16.25-1997 Buttwelding Ends Includes Interpretation No. 1 ASME B16.26 Cast Copper Alloy Fittings for Flared Copper Tubes ASME B16.28 Wrought Steel Buttwelding Short Radius Elbows and Returns ASME B16.28 INTERPRETATIONS Interpretations to B16.28-1994 Wrought Steel Buttwelding Short Radius Elbows and Returns Includes Interpretations No. 1 ASME B16.29 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings - DWV ASME B16.33 Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig (Sizes 1/2 Through 2) ASME B16.34 Valves - Flanged, Threaded, and Welding End ASME B16.34 INTERPRETATIONS Interpretations to B16.34-1996 Valves - Flanged, Threaded, and Welding End Includes Interpretation No. 2 ASME B16.34A Addenda to B16.34-1996 Valves - Flanged, Threaded, and Welding End ASME B16.36 Orifice Flanges ASME B16.36 INTERPRETATIONS Interpretations to B16.36-1996 Orifice Flanges ASME B16.38 Large Metallic Valves for Gas Distribution (Manually Operated, NPS 2 1/2 to 12, 125 psig Maximum) R(1994) ASME B16.39 Malleable Iron Threaded Pipe Unions Classes 150, 250, and 300 ASME B16.40 Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems R(1994) ASME B16.41 Functional Qualification Requirements for Power Operated Active Valve Assemblies for Nuclear Power Plants R(1989) ASME B16.41 ASME B16.42 Ductile Iron Pipe Flanges and Flanged Fittings Classes 150 and 300 ASME B16.43 (Withdrawn) Wrought Copper and Copper Alloy Solder Joint Fittings for Sovent Drainage Systems ASME B16.44 Manually Operated Metallic Gas Valves for Use in House Piping Systems ASME B16.44A Addenda to B16.44-1995 Manually Operated Metallic Gas Valves for Use in House Piping Systems ASME B16.45 Cast Iron Fittings for Sovent Drainage Systems ASME B16.47 Large Diameter Steel Flanges NPS 26 Through NPS 60 ASME B16.47 INTERPRETATIONS Interpretations to B16.47-1996 Large Diameter Steel Flanges NPS 26 Through NPS 60 ASME B16.47A Addenda to B16.47-1990 Large Diameter Steel Flanges NPS 26 Through NPS 60

ASME B16.48 Steel Line Blanks ASME B16.49 Factory-Made Wrought Steel Buttwelding Induction Bends for Transportation and Distribution Systems ASME B17.1 Keys and Keyseats R(1998) ASME B17.2 Woodruff Keys and Keyseats Revision of USAS B17F-1930 R(1998) ASME B18.1.1 Small Solid Rivets 7/16 Inch Nominal Diameter and Smaller Revision of B18.1-1965 R(1995) ASME B18.1.2 Large Rivets 1/2 Inch Nominal Diameter and Larger Revision of B18.4-1960 R(1995) ASME B18.1.3M Metric Small Solid Rivets 12 mm Nominal Diameter and Smaller Errata - October 1985 R(1995) ASME B18.2.1 Square and Hex Bolts and Screws (Inch Series) ASME B18.2.1A Addenda to ASME B18.2.1-1996 Square and Hex Bolts and Screws (Inch Series) ASME B18.2.3.1M Metric Hex Cap Screws ASME B18.2.3.2M Metric Formed Hex Screws Errata - December 1980 R(1995) ASME B18.2.3.3M Metric Heavy Hex Screws Errata - April 1981 R(1995) ASME B18.2.3.4M Metric Hex Flange Screws R(1995) ASME B18.2.3.5M Metric Hex Bolts Errata - May 1981 R(1995) ASME B18.2.3.6M Metric Heavy Hex Bolts Errata - April 1981 R(1995) ASME B18.2.3.7M Metric Heavy Hex Structural Bolts Errata - April 1981 R(1995) ASME B18.2.3.9M Metric Heavy Hex Flange Screws R(1995) ASME B18.2.3.10M Square Head Bolts (Metric Series) ASME B18.2.4.1M Metric Hex Nuts, Style 1 Errata - May 1981 R(1995) ASME B18.2.4.2M Metric Hex Nuts, Style 2 Errata - January 1982 R(1995) ASME B18.2.4.3M Metric Slotted Hex Nuts Errata - May 1981 R(1995) ASME B18.2.4.4M Metric Hex Flange Nuts R(1993) ASME B18.2.4.4M ASME B18.2.4.5M Metric Hex Jam Nuts Errata - May 1981 R(1998) ASME B18.2.4.6M Metric Heavy Hex Nuts Errata - April 1981 R(1998) ASME B18.2.6 Fasteners for Use in Structural Applications ASME B18.2.8 Clearance Holes for Bolts, Screws, and Studs ASME B18.3 Socket Cap, Shoulder, and Set Screws, Hex and Spline Keys (Inch Series) ASME B18.3.1M Socket Head Cap Screws (Metric Series) R(1993) ASME B18.3.2M Metric Series Hexagon Keys and Bits R(1998) ASME B18.3.3M Hexagon Socket Head Shoulder Screws (Metric Series) R(1993) ASME B18.3.4M Hexagon Socket Button Head Cap Screws (Metric Series) R(1993) ASME B18.3.5M Hexagon Socket Flat Countersunk Head Cap Screws (Metric Series) R(1993) ASME B18.3.6M Metric Series Socket Set Screws R(1993) ASME B18.5 Round Head Bolts (Inch Series) R(1998) ASME B18.5.2.1M Metric Round Head Short Square Neck Bolts ASME B18.5.2.2M Metric Round Head Square Neck Bolts R(1993) ASME B18.5.2.2M ASME B18.5.2.3M Round Head Square Neck Bolts with Large Head (Metric Series) R(1998) ASME B18.6.1 Wood Screws (Inch Series) R(1997) ASME B18.6.2 Slotted Head Cap Screws, Square Head Set Screws, and Slotted Headless Set Screws

(Inch Series) ASME B18.6.3 Machine Screws and Machine Screw Nuts ASME B18.6.4 Thread Forming and Thread Cutting Tapping Screws and Metallic Drive Screws (Inch Series) ASME B18.6.5M Metric Thread-Forming and Thread-Cutting Tapping Screws 2000 Edition; Revision of ANSI/ASME B18.6.5M-1986(R1993) ASME B18.6.7M Metric Machine Screws 2000 Edition; Revision of ASME B18.6.7M-1985(1993) ASME B18.7 General Purpose Semi-Tubular Rivets, Full Tubular Rivets, Split Rivets and Rivet Caps R(1992) ASME B18.7.1M Metric General Purpose Semi-Tubular Rivets R(1992) ASME B18.7.1M ASME B18.8.1 Clevis Pins and Cotter Pins (Inch Series) Errata - April 1995 ASME B18.8.1 ASME B18.8.2 Taper Pins, Dowel Pins, Straight Pins, Grooved Pins, and Spring Pins (Inch Series) ASME B18.8.3M Spring Pins - Coiled Type (Metric Series) ASME B18.8.4M Spring Pins - Slotted (Metric Series) ASME B18.8.5M Machine Dowel Pins - Hardened Ground (Metric Series) ASME B18.8.6M Cotter Pins (Metric Series) ASME B18.8.6M ASME B18.8.7M Headless Clevis Pins (Metric Series) ASME B18.8.7M ASME B18.8.8M Headed Clevis Pins (Metric Series) ASME B18.8.8M ASME B18.8.9M Grooved Pins (Metric Series) ASME B18.8.200M Cotter Pins, Headless Clevis Pins, and Headed Clevis Pins Metric Series ASME B18.9 Plow Bolts (Inch Series) ASME B18.10 Track Bolts and Nuts R(1992) ASME B18.10 ASME B18.11 Miniature Screws R(1992) ASME B18.12 Glossary of Terms for Mechanical Fasteners R(1991) ASME B18.13 Screw and Washer Assemblies - Sems (Inch Series) ASME B18.13.1M Screw and Washer Assemblies - Sems (Metric Series) ASME B18.15 Forged Eyebolts R(1995) ASME B18.15M Metric Lifting Eyes Incorporating ASME B18.15.1M-1998 and ASME B18.15.2M-1998 ASME B18.16.1M Mechanical and Performance Requirements for Prevailing-Torque Type Steel Metric Hex Nuts and Hex Flange Nuts Errata - December 1980 R(1995) ASME B18.16.2M Torque-Tension Test Requirements for Prevailing-Torque Type Steel Metric Hex Nuts and Hex Flange Nuts R(1995) ASME B18.16.3M Dimensional Requirements for Prevailing-Torque Type Steel Metric Hex Nuts and Hex Flange Nuts ASME B18.18.2M SUPPLEMENT Supplement of ASME B18.18.2m-1987 Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners ASME B18.18.5M Inspection and Quality Assurance Plan Requiring In-Process Inspection and Controls ASME B18.18.6M Quality Assurance Plan for Fasteners Produced in a Third Party Accreditation System

ASME B18.18.7M Quality Assurance Plan for Fasteners Produced in a Customer Approved Control Plan ASME B18.21.1 Lock Washers (Inch Series) ASME B18.21.2M Lock Washers (Metric Series) ASME B18.22.1 Plain Washers Reaffirmation and Redesignation of ASA B27.2-1965 R(1998) ASME B18.22.1 ASME B18.23.1 (Withdrawn) Beveled Washers Reaffirmation and Redesignation of USAS B27.4-1967 R(1975) ASME B18.24.1 Part Identifying Number (PIN) Code System Standard for B18 Externally Threaded Products ASME B18.24.2 Part Identifying Number (PIN) Code System Standard for B18 Internally Threaded Products ASME B18.24.3 Part Identifying Number (PIN) Code System Standard for B18 Nonthreaded Products ASME B18.25.1M Square and Rectangular Keys and Keyways ASME B18.25.2M Woodruff Keys and Keyways ASME B18.25.3M Square and Rectangular Keys and Keyways: Width Tolerances and Deviations Greater than Basic Size ASME B18.27 Tapered and Reduced Cross Section Retaining Rings (Inch Series) Incorporating ASME B18.27.1, B18.27.2, B18.27.3, B18.27.4, and B18.27.5 ASME B18.27A Addenda to ASME B18.27-1998 Tapered and Reduced Cross Section Retaining Rings (Inch Series) ASME B18.27B Addenda to ASME B18.27-1998 Tapered and Reduced Cross Section Retaining Rings (Inch Series) ASME B18.29.1 Helical Coil Screw Thread Inserts - Free Running and Screw Locking (Inch Series) Errata - August 1995 ASME B19.1 Safety Standard for Air Compressor Systems ASME B19.3 Safety Standard for Compressors for Process Industries ASME B19.3A Addenda to B19.3-1991 Safety Standard for Compressors for Process Industries ASME B19.3B Addenda to B19.3-1991 Safety Standard for Compressors for Process Industries ASME B20.1 Safety Standard for Conveyors and Related Equipment

2006

2007-03-25 20:17

ASME B20.1 INTERPRETATIONS Interpretations to B20.1-1996 Safety Standard for Conveyors and Related Equipment Includes Interpretation No. A and B ASME B20.1A Addenda to B20.1-1996 Safety Standard for Conveyors and Related Equipment ASME B20.1B Addenda to B20.1 - 1996 Safety Standard for Conveyors and Related Equipment ASME B27.8M General Purpose Metric Tapered and Reduced Cross Section Retaining Rings Type 3DM1 - Heavy Duty External Rings Type 3EM1 - Reinforced "E" Rings Type 3FM1 - "C" Type Rings R(1993) ASME B27.8M ASME B29.1M Precision Power Transmission Roller Chains, Attachments, and Sprockets R(1999) ASME B29.2M Inverted Tooth (Silent) Chains and Sprockets (Revision of B29.2-1957 and B29.9-1958); Errata - July 1985 R(1999) ASME B29.3M Double-Pitch Power Transmission Roller Chains and Sprockets R(1999) ASME B29.4M Double-Pitch Conveyor Roller Chains, Attachments, and Sprockets R(1999)

ASME B29.6M Steel Detachable Link Chains, Attachments, and Sprockets ASME B29.6M ASME B29.8M Leaf Chains, Clevises, and Sheaves ASME B29.10M Heavy Duty Offset Sidebar Power Transmission Roller Chains and Sprocket Teeth ASME B29.11M Combination Chains, Attachments, and Sprocket Teeth ASME B29.12M Steel Bushed Rollerless Chains, Attachments, and Sprocket Teeth ASME B29.14M "H" Type Mill Chains, Attachments, and Sprocket Teeth ASME B29.15M Steel Roller Type Conveyor Chains, Attachments, and Sprocket Teeth ASME B29.16M Welded Steel Type Mill Chains, Attachments, and Sprocket Teeth Special Notice ASME B29.17M Hinge Type Flat Top Conveyor Chains and Sprocket Teeth ASME B29.18M Welded Steel-Type Drag Chains, Attachments, and Sprocket Teeth ASME B29.19M Agricultural Roller Chains, Attachments, and Sprockets ASME B29.19M ASME B29.21M 700 Class Welded Steel and Cast Chains, Attachments and Sprockets for Water and Sewage Treatment Plants ASME B29.22M Drop Forged Rivetless Chains, Sprocket Teeth Drive Chain/Drive Dogs ASME B29.23M Flexible Chain Couplings R(1995) ASME B29.24M Roller Load Chains for Overhead Hoists ASME B29.25M Open Barrel Steel Pintle-Type Conveyor Chains, Attachments, and Sprockets ASME B29.26M Fatigue Testing Power Transmission Roller Chain ASME B29.300 Agricultural, Detachable, and Pintle Chains, Attachments, and Sprockets Incorporating ASME B29.6, B29.19, and B29.25 ASME B30.1 Jacks ASME B30.2 Overhead and Gantry Cranes Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist ASME B30.2 INTERPRETATIONS Interpretations to B30.2-1996 Overhead and Gantry Cranes Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist Includes Interpretation No. 1 Through 3 ASME B30.2A Addenda to B30.2-1996 Overhead and Gantry Cranes (Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist) ASME B30.2B Addenda to B30.2-1996 Overhead and Gantry Cranes (Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist) ASME B30.3 Construction Tower Cranes ASME B30.3 INTERPRETATIONS Interpretations to B30.3-1996 Hammerhead Tower Cranes ASME B30.3A Addenda to B30.3-1996 Construction Tower Cranes ASME B30.3B Addenda to B30.3-1996 Construction Tower Cranes ASME B30.3C Addenda to B30.3-1996 Construction Tower Cranes ASME B30.4 Portal, Tower, and Pedestal Cranes ASME B30.4 INTERPRETATIONS Interpretations to B30.4-1996 Portal, Tower, and Pedestal Cranes ASME B30.4A Addenda to B30.4-1996 Portal, Tower, and Pedestal Cranes ASME B30.4B Addenda to B30.4-1996 Portal, Tower and Pedestal Cranes ASME B30.5 Mobile and Locomotive Cranes ASME B30.5 ASME B30.5 INTERPRETATIONS Interpretations to B30.5-1994 Mobile and Locomotive Cranes

ASME B30.5A Addenda to B30.5-1994 Mobile and Locomotive Cranes ASME B30.5B Addenda to B30.5-1994 Mobile and Locomotive Cranes ASME B30.5C Addenda to B30.5 - 1994 Mobile and Locomotive Cranes ASME B30.5D Addenda to B30.5 - 1994 Mobile and Locomotive Cranes ASME B30.6 Derricks ASME B30.6A Addenda to B30.6-1995 Derricks ASME B30.6B Addenda to B30.6-1995 Derricks ASME B30.7 Base Mounted Drum Hoists ASME B30.7A Addenda to B30.7-1994 Base Mounted Drum Hoists ASME B30.7B Addenda to B30.7-1994 Base Mounted Drum Hoists ASME B30.7C Addenda to B30.7-1994 Base Mounted Drum Hoists ASME B30.8 Floating Cranes and Floating Derricks ASME B30.8 INTERPRETATIONS Interpretations to B30.8-1993 Floating Cranes and Floating Derricks ASME B30.8A Addenda to B30.8-1993 Floating Cranes and Floating Derricks ASME B30.8B Addenda to B30.8-1993 Floating Cranes and Floating Derricks ASME B30.8C Addenda to B30.8-1993 Floating Cranes and Floating Derricks ASME B30.9 Slings Safety Standard for Cableways, Cranes, Derricks, Hoists, Hooks, Jacks, and Slings FSC 3940; Should Be Used Instead of MIL-S-52432A ASME B30.9 INTERPRETATIONS Interpretations to B30.9-1996 Slings ASME B30.9A Addenda to B30.9-1996 Slings ASME B30.9B Addenda to B30.9-1996 Slings ASME B30.9C Addenda to B30.9-1996 Slings ASME B30.10 Hooks ASME B30.10 INTERPRETATIONS Interpretations to B30.10-1993 Hooks ASME B30.10A Addenda to B30.10-1993 Hooks ASME B30.10B Addenda to B30.10-1993 Hooks ASME B30.11 Monorails and Underhung Cranes ASME B30.11 INTERPRETATION Interpretations to B30.11 - 1998 Monorails and Underhung Cranes ASME B30.11A Addenda to B30.11 - 1998 Monorails and Underhung Cranes ASME B30.12 Handling Loads Suspended from Rotorcraft ASME B30.12A Addenda to B30.12-1992 Handling Loads Suspended from Rotorcraft ASME B30.12B Addenda to B30.12-1992 Handling Loads Suspended from Rotorcraft ASME B30.13 Storage/Retrieval (S/R) Machines and Associated Equipment ASME B30.13 INTERPRETATIONS Interpretations to B30.13-1996 Storage/Retrieval (S/R) Machines and Associated Equipment ASME B30.13A Addenda to B30.13-1996 Storage/Retrieval (S/R) Machines and Associated Equipment ASME B30.13B Addenda to B30.13-1996 Storage/Retrieval (S/R) Machines and Associated Equipment ASME B30.13C Addenda to B30.13-1996 Storage/Retrieval (S/R) Machines and Associated Equipment ASME B30.14 Side Boom Tractors ASME B30.14A Addenda to B30.14-1996 Side Boom Tractors ASME B30.16 Overhead Hoists (Underhung) ASME B30.16 INTERPRETATIONS Interpretations to B30.16-1998 Overhead Hoists (Underhung) ASME B30.17 Overhead and Gantry Cranes (Top Running Bridge, Single Girder, Underhung Hoist) ASME B30.17 INTERPRETATIONS Interpretations to B30.17-1998 Overhead and Gantry Cranes (Top

Running Bridge, Single Girder, Underhung Hoist) ASME B30.18 Stacker Cranes (Top or Under Running Bridge, Multiple Girder with Top or Under Running Trolley Hoist) ASME B30.20 Below-the-Hook Lifting Devices ASME B30.20 INTERPRETATIONS Interpretations to B30.20-1993 Below-The-Hook Lifting Devices ASME B30.20A Addenda to B30.20-1993 Below-The-Hook Lifting Devices ASME B30.20B Addenda to B30.20-1993 Below-The-Hook Lifting Devices ASME B30.20C Addenda to B30.20-1993 Below-The-Hook Lifting Devices ASME B30.21 Manually Lever Operated Hoists ASME B30.21 INTERPRETATIONS Interpretations to B30.2-1994 Manually Lever Operated Hoists ASME B30.21A Addenda to B30.21-1994 Manually Lever Operated Hoists ASME B30.21B Addenda to B30.21-1994 Manually Lever Operated Hoists ASME B30.22 Articulating Boom Cranes ASME B30.22 INTERPRETATIONS Interpretations to B30.22-1993 Articulating Boom Cranes ASME B30.22A Addenda to B30.22-1993 Articulating Boom Cranes ASME B30.22B Addenda to B30.22-1993 Articulating Boom Cranes ASME B30.22C Addenda to B30.22-1993 Articulating Boom Cranes ASME B30.22D Addenda to B30.22 - 1993 Articulating Boom Cranes ASME B30.23 Personnel Lifting Systems ASME B30.25 Scrap and Material Handlers ASME B31.1 Power Piping ASME B31.1 CASES NO. 25 Cases No. 25 to B31.1 Power Piping ASME B31.1 CASES NO. 26 Cases No. 26 to B31.1 Power Piping ASME B31.1 INTERPRETATIONS Interpretations to B31.1-1998 Power Piping Includes Interpretation No. 31 ASME B31.1A Addenda to B31.1-1998 Power Piping ASME B31.2 Fuel Gas Piping ASME B31.3 Process Piping ASME B31.3 INTERPRETATIONS Interpretations to B31.3-1999 Process Piping Includes Interpretations No. 14 Through 17 ASME B31.3A Addenda to Process Piping ASME B31.4 Pipeline Transportation Systems for Liquid Hydrocarbons and other Liquids ASME B31.4 CASES NO. 4 Cases No. 4 to B31.4 Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids ASME B31.4 INTERPRETATIONS Intrepretations to B31.4-1998 Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids Includes Interpretation No. 5 ASME B31.5 Refrigeration Piping Errata - 1993 ASME B31.5 INTERPRETATIONS Interpretations to B31.5-1992 Refrigreration Piping Includes Interpretation No. 5 ASME B31.5A Addenda to B31.5-1992 Refrigeration Piping ASME B31.8 Gas Transmission and Distribution Piping Systems ASME B31.9 Building Services Piping ASME B31.9 INTERPRETATIONS Interpretations to B31.9-1996 Building Services Piping Includes Interpretation No. 1

ASME B31.11 Slurry Transportation Piping Systems Special Notice - 1990 R(1998) ASME B31.11 INTERPRETATIONS Interpretations to B31.11-1989 Slurry Transportation Piping Systems ASME B31.11A Addenda to B31.11-1989 Slurry Transportation Piping Systems ASME B31G Manual for Determining the Remaining Strength of Corroded Pipelines a Supplement to ASME B31 Code for Pressure Piping ASME B32.1 Preferred Thicknesses for Uncoated Thin Flat Metals (Under 0.025 in.) R(1994) ASME B32.2 Preferred Diameters for Round Wire (0.500 Inches and Under) R(1994) ASME B32.3M Preferred Metric Sizes for Flat Metal Products R(1994) ASME B32.4M Preferred Metric Sizes for Round, Square, Rectangle and Hexagon Metal Products Revision of ANSI B32.4-1977 R(1994) ASME B32.5 Preferred Metric Sizes for Tubular Metal Products Other Than Pipe Errata - 1996 R(1994) ASME B32.6M Preferred Metric Equivalents of Inch Sizes for Tubular Metal Products Other Than Pipe Revision of ANSI B32.6 -1977 R(1994) ASME B36.10M Welded and Seamless Wrought Steel Pipe ASME B36.10M ASME B36.19M Stainless Steel Pipe Revision of ANSI B36.19-1976 R(1994) ASME B36.19M ASME B40.2 Diaphragm Seals ASME B40.3 Bimetallic Actuated Thermometers ASME B40.5 Snubbers ASME B40.6 Pressure Limiter Valves ASME B40.100 Pressure Gauges and Gauge Attachments Incorporating ASME B40.1-1998 and ASME B40.7-1998 ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay) ASME B47.1 Gage Blanks Revision of ANSI/ASME B47.1AM-1982 R(1999) ASME B56.1 Safety Standard for Low Lift and High Lift Trucks ASME B56.1 INTERPRETATIONS Interpretations to B56.1-1993 Safety Standard for Low Lift and High Lift Trucks ASME B56.1A Addenda to B56.1-1993 Safety Standard for Low Lift and High Lift Trucks ASME B56.5 INTERPRETATIONS Interpretations to B56.5-1993 Safety Standard for Guided Industrial Vehicles and Automated Functions of Manned Industrial Vehicles ASME B56.5A Addenda to B56.5-1993 Safety Standard for Guided Industrial Vehicles and Automated Functions of Manned Industrial Vehicles ASME B56.6 Safety Standard for Rough Terrain Forklift Trucks ASME B56.6 INTERPRETATIONS Interpretations to B56.6-1993 Safety Standard for Rough Terrain Forklift Trucks ASME B56.6A Addenda to B56.6-1993 Safety Standard for Rough Terrain Forklift Trucks ASME B56.6B Addenda to B56.6-1992 Safety Standard for Rough Terrain Forklift Trucks ASME B56.7 Safety Standard for Industrial Crane Trucks Special Notice - June 1988 R(1992) ASME B56.8 INTERPRETATIONS Interpretations to B56.8-1993 Safety Standard for Personnel and Burden Carriers ASME B56.8A Addenda to B56.8-1993 Safety Standard for Personnel and Burden Carriers ASME B56.9 INTERPRETATIONS Interpretations to B56.9-1992 Safety Standard for Operator

Controlled Industrial Tow Tractors ASME B56.9A Addenda to B56.9-1992 Safety Standard for Operator Controlled Industrial Tow Tractors ASME B56.10 Safety Standard for Manually Propelled High Lift Industrial Trucks Special Notice October 1993 ASME B56.10 ASME B56.11.4 Hook-Type Forks and Fork Carriers for Powered Industrial Forklift Trucks Special Notice - February 1993 ASME B56.11.4 ASME B56.11.4A Addenda to B56.11.4-1992 Hook-Type Forks and Fork Carriers for Powered Industrial Forklift Trucks ASME B56.11.5A Addenda to B56.11.5-1992 Measurement of Sound Emitted by Low Lift, High Lift, and Rough Terrain Powered Industrial Trucks ASME B56.11.7 Liquid Propane Gas (LPG) Fuel Cylinders (Horizontal or Vertical) Mounting - Liquid Withdrawal - For Powered Industrial Trucks ASME B73.1 (Pending) Specification for Horizontal End Suction Centrifugal Pumps for Chemical Process Comment Period Ends: 2000-09-12 ASME B73.1M Specification for Horizontal End Suction Centrifugal Pumps for Chemical Process Errata - August 1992 R(1999) ASME B73.2M Specification for Vertical In-Line Centrifugal Pumps for Chemical Process R(1999) ASME B73.3M Specification for Sealless Horizontal End Suction Centrifugal Pumps for Chemical Process ASME B73.5M Specification for Thermoplastic and Thermoset Polymer Material Horizontal End Suction Centrifugal Pumps for Chemical Process ASME B89.1.2M Calibration of Gage Blocks by Contact Comparison Methods (Through 20 in. and 500 mm) ASME B89.1.5 Measurement of Plain External Diameters for Use as Master Discs or Cylindrical Plug Gages ASME B89.1.6M Measurement of Qualified Plain Internal Diameters for Use as Master Rings and Ring Gages R(1997) ASME B89.1.9M Precision Gage Blocks for Length Measurement (Through 20 in. and 500 mm) R(1997) ASME B89.1.10M Dial Indicators (for Linear Measurements) Revision of ANSI B89.1.10-1978 R(1995) ASME B89.3.1 Measurement of Out-Of-Roundness R(1997) ASME B89.3.4M Axes of Rotation Methods for Specifying and Testing R(1992) ASME B89.4.1 Methods for Performance Evaluation of Coordinate Measuring Machines Revision of ASME B89.1.12M-1990 ASME B89.4.1A Addenda to B89.4.1-1997 Methods for Performance Evaluation of Coordinate Measuring Machines ASME B89.4.10 (Pending) Methods for Performance Evaluation of Coordinate Measuring Systems Software Comment Period Ends: 2000-09-12 ASME B89.6.2 Temperature and Humidity Environment for Dimensional Measurement R(1995) ASME B89.7.2 Dimensional Measurement Planning ASME B89 TECH PAPER Space Plate Test Recommendations for Coordinate Measuring Machines

ASME B89 TECH REPT Parametric Calibration of Coordinate Measuring Machines ASME B94.2 Reamers ASME B94.3 Straight Cut-Off Blades for Lathes and Screw Machines R(1995) ASME B94.6 Knurling R(1995) ASME B94.7 Hobs R(1995) ASME B94.8 Inserted Blade Milling Cutter Bodies Revision of USAS B5.23-1958 R(1998) ASME B94.9 Taps: Ground and Cut Threads (Inch and Metric Sizes) ASME B94.11M Twist Drills ASME B94.14 (Pending) Punches - Basic Head Type Comment Period Ends: 2000-08-15 R(2000) ASME B94.14 Punches - Basic Head Type R(1995) ASME B94.14 ASME B94.14.1 Punches - Basic Head Type (Metric) R(1995) ASME B94.14.1 (Pending) Punches - Basic Head Type (Metric) Comment Period Ends: 2000-08-15 R(2000) ASME B94.16 (Pending) Retainers - Basic Ball-Lock Punch and Die Button, Light and Heavy Duty Comment Period End: 2000-08-15 R(2000) ASME B94.16 Retainers - Basic Ball-Lock Punch and Die Button, Light and Heavy Duty R(1995) ASME B94.16 ASME B94.16.1 (Pending) Retainers - Basic Ball-Lock Punch and Die Button Light and Heavy Duty (Metric) Comment Period Ends: 2000-08-15 R(2000) ASME B94.16.1 Retainers - Basic Ball-Lock Punch and Die Button Light and Heavy Duty (Metric) R(1995) ASME B94.16.1 ASME B94.17 Gages - Functional, Ball-Lock Punches, Die Buttons and Retainers R(1995) ASME B94.17 (Pending) Gages - Functional, Ball-Lock Punches, Die Buttons and Retainers Comment Period Ends: 2000-08-15 R(2000) ASME B94.17.1 Gages - Functional, Ball-Lock Punches, Die Buttons and Retainers (Metric) R(1995) ASME B94.17.1 (Pending) Gages - Functional, Ball-Lock Punches, Die Buttons and Retainers (Metric) Comment Period Ends: 2000-08-15 R(2000) ASME B94.18 Punches - Basic Ball-Lock, Light and Heavy Duty Comment Period Ends: 2000-08-15 ASME B94.18.1 (Pending) Punches - Basic Ball-Lock Light and Heavy Duty (Metric) Comment Period Ends: 2000-08-15 R(2000) ASME B94.18.1 Punches - Basic Ball-Lock Light and Heavy Duty (Metric) R(1995) ASME B94.18.1 ASME B94.19 Milling Cutters and End Mills ASME B94.21 Gear Shaper Cutters R(1995) ASME B94.22 (Pending) Punches-Variable Head Type Comment Period Ends: 2000-08-15 R(2000) ASME B94.22 Punches-Variable, Head Type R(1995) ASME B94.22 ASME B94.22.1 Punches-Variable, Head Type (Metric) R(1995) ASME B94.22.1 ASME B94.22.1 (Pending) Punches-Variable, Head Type (Metric) Comment Period Ends: 2000-08-15 R(2000) ASME B94.23 Punch Guide Bushings - Variable, Press Fit R(1995)

ASME B94.23 ASME B94.23 (Pending) Punch Guide Bushings - Variable, Press Fit Comment Period Ends: 2000-08-15 R(2000) ASME B94.27 Die Buttons Basic Taper Relief, Press Fit R(1995) ASME B94.27 ASME B94.27 (Pending) Die Buttons Basic Taper Relief, Press Fit Comment Period Ends: 2000-08-15 R(2000) ASME B94.27.1M (Pending) Die Buttons - Basic Taper Relief, Press Fit (Metric) Comment Period Ends: 2000-08-15 R(2000) ASME B94.27.1M Die Buttons - Basic Taper Relief, Press Fit (Metric) R(1995) ASME B94.27.1M ASME B94.28 (Pending) Die Buttons Basic Straight Relief, Press Fit Comment Period Ends: 2000-08-15 R(2000) ASME B94.28 Die Buttons Basic Straight Relief, Press Fit R(1995) ASME B94.28 ASME B94.28.1M Die Buttons - Basic Straight Relief, Press Fit (Metric) R(1995) ASME B94.28.1M ASME B94.28.1M (Pending) Die Buttons - Basic Straight Relief, Press Fit (Metric) Comment Period Ends: 2000-08-15 R(2000) ASME B94.29 Die Buttons - Basic Ball-Lock R(1995) ASME B94.29 ASME B94.29 (Pending) Die Buttons - Basic Ball-Lock Comment Period Ends: 2000-08-15 R(2000) ASME B94.29.1 (Pending) Die Buttons - Basic Ball-Lock (Metric) Comment Period Ends: 2000-08-15 R(2000) ASME B94.29.1 Die Buttons - Basic Ball-Lock (Metric) R(1995) ASME B94.29.1 ASME B94.30 Die Buttons Variable, Press Fit Comment Period Ends: 2000-08-15 R(1995) ASME B94.31 Steel Rotary Slitting Knives and Steel Spacing Collars R(1995) ASME B94.31 (Pending) Steel Rotary Slitting Knives and Steel Spacing Collars Comment Period Ends: 2000-08-15 R(2000) ASME B94.33 Jig Bushings ASME B94.33.1 Jig Bushings (Metric) ASME B94.35 Drill Drivers, Split-Sleeve, Collet Type R(1995) ASME B94.37M Roller Turner Type Cutting Tools, Single Point Revision of B94.37-1972 R(1985) ASME B94.38 (Pending) Punches-Variable, Angle Head Type and Related Quill Bushings Comment Period Ends: 2000-08-15 R(2000) ASME B94.38 Punches-Variable, Angle Head Type and Related Quill Bushings R(1995) ASME B94.39 (Pending) Punches - Basic, Combination Angle Head Type and Related Quill Bushings Comment Period Ends: 2000-08-15 R(2000) ASME B94.39 Punches - Basic, Combination Angle Head Type and Related Quill Bushings R(1995) ASME B94.40 Punches - Wire Type R(1995) ASME B94.40 (Pending) Punches - Wire Type Comment Period Ends: 2000-08-15 R(2000) ASME B94.41 Punches - Basic, Angle Head Type and Related Quill Bushings R(1995) ASME B94.41 (Pending) Punches - Basic, Angle Head Type and Related Quill Bushings Comment

Period Ends: 2000-08-15 R(2000) ASME B94.43 Die Buttons Variable, Press Fit, Headless and Head Type, Step Relief R(1995) ASME B94.43 (Pending) Die Buttons Variable, Press Fit, Headless and Head Type, Step Relief Comment Period Ends: 2000-08-15 R(2000) ASME B94.44 (Pending) Punches - Basic, Cylindrical Head Type and Related Quill Bushings Comment Period Ends: 2000-08-15 R(2000) ASME B94.44 Punches - Basic, Cylindrical Head Type and Related Quill Bushings R(1995) ASME B94.44 ASME B94.49 Spade Drill Blades and Spade Drill Holders R(1995) ASME B94.50 Basic Nomenclature and Definitions for Single-Point Cutting Tools R(1995) ASME B94.51M Specifications for Band Saw Blades (Metal Cutting) ASME B94.52M Specifications for Hacksaw Blades ASME B94.53 Solid Steel Rectangular Metal Cutting Squaring Shear Knives Dimensional Tolerances R(1984) ASME B94.54 Specifications for Hole Saws, Hole Saw Arbors, and Hole Saw Accessories ASME B94.55M Tool Life Testing with Single-Point Turning Tools Revision of ANSI B94.34-1946 and B94.36-1956 R(1995) ASME B94.56 Gages - Functional, Ball-Lock Punches (Inch) ASME B94.56.1M Gages - Functional, Ball-Lock Punches (Metric) ASME B96.1 Welded Aluminum-Alloy Storage Tanks ASME B106.1M (Withdrawn) Design of Transmission Shafting (Second Printing) ASME B107.1 Socket Wrenches, Hand (Inch Series) ASME B107.2 Socket Wrenches, Extensions, Adaptors, and Universal Joints, Power Drive (Impact) (Inch Series) ASME B107.4M Driving and Spindle Ends for Portable Hand, Impact, Air, and Electric Tools (Percussion Tools Excluded) ASME B107.5M Socket Wrenches, Hand (Metric Series) ASME B107.6 Wrenches, Box, Angled, Open End, Combination, Flare Nut, and Tappet (Inch Series) ASME B107.8M Adjustable Wrenches ASME B107.9M Wrenches, Box, Angled, Open End, Combination, Flare Nut, and Tappet (Metric Series) Errata - 1996 ASME B107.10M Handles and Attachments for Hand Socket Wrenches - Inch and Metric Series ASME B107.11M Pliers, Diagonal Cutting, and Nippers, End Cutting ASME B107.12 Nut Drivers (Spin Type, Screwdriver Grip)(Inch Series) ASME B107.13M Pliers - Long Nose, Long Reach ASME B107.14M Hand Torque Tools ASME B107.15 Flat Tip and Phillips Screwdrivers ASME B107.16M Shears (Metal Cutting, Hand) ASME B107.17M Gages, Wrench Openings, Reference ASME B107.18M Pliers (Wire Twister) ASME B107.19 Pliers, Retaining Ring ASME B107.19 ASME B107.20M Pliers (Lineman's, Iron Worker's, Gas, Glass, Fence, and Battery) ASME B107.21 Wrench, Crowfoot Attachments (Inch Series)

ASME B107.22M Electronic Cutters Errata - May 1999 ASME B107.23M Pliers, Multiple Position, Adjustable ASME B107.25M Pliers - Performance Test Methods ASME B107.27 Pliers, Multiple Position (Electrical Connector) ASME B107.28M Electronic Torque Instruments ASME B107.29M Electronic Tester, Hand Torque Tools ASME B107.31M Screwdrivers, Cross Tip Gaging ASME B107.34M Socket Wrenches for Spark Plugs ASME B107.35M Nut Drivers (Spin Type, Screwdriver Grip)(Metric Series) ASME B107.38M Electronic Pliers ASME B107.41M Nail Hammers - Safety Requirements ASME B107.42M Hatchets: Safety Requirements ASME B107.43M Wood-Splitting Wedges: Safety Requirements ASME B107.44M Glaziers' Chisels and Wood Chisels; Safety Requirements ASME B107.45M Ripping Chisels and Flooring/Electricians' Chisels: Safety Requirements ASME B107.46M Stud, Screw, and Pipe Extractors: Safety Requirements ASME B107.47M Metal Chisels: Safety Requirements ASME B107.48M Metal Punches and Drift Pins: Safety Requirements ASME B107.49M Nail Sets: Safety Requirements ASME B107.50M Brick Chisels and Brick Sets: Safety Requirements ASME B107.53M Ball Peen Hammers: Safety Requirements ASME B107.55M Axes: Safety Requirements ASME B107.56 Body Repair Hammers and Dolly Blocks: Safety Requirements Formerly ANSI/HTI B173.5-1991 ASME B133.1M Gas Turbine Terminology R(1997) ASME B133.2 Basic Gas Turbine R(1997) ASME B133.2 ASME B133.3 Procurement Standard for Gas Turbine Auxiliary Equipment R(1994) ASME B133.4 Gas Turbine Control and Protection Systems R(1997) ASME B133.5 Procurement Standard for Gas Turbine Electrical Equipment R(1997) ASME B133.6 Procurement Standard for Gas Turbine Ratings and Performance R(1994) ASME B133.6 ASME B133.7M Gas Turbine Fuels Revision of ANSI B133.7-1977 R(1992) ASME B133.8 Gas Turbine Installation Sound Emissions R(1989) ASME B133.9 Measurement of Exhaust Emissions from Stationary Gas Turbine Engines Revision of ANSI B133.9-1979 ASME B133.10 Procurement Standard for Gas Turbine Information to Be Supplied by User and Manufacturer R(1994) ASME B133.11 Procurement Standard for Gas Turbine Preparation for Shipping and Installation R(1994) ASME B133.12 Procurement Standard for Gas Turbine Maintenance and Safety R(1994) ASME B133.16 Procurement Standard for Gas Turbine Marine Applications ASME BPE Bioprocessing Equipment ASME CSD-1 Controls and Safety Devices for Automatically Fired Boilers

ASME CSD-1 INTERPRETATIONS Interpretations to CSD-1-1998 Controls and Safety Devices for Automatically Fired Boilers ASME CSD-1A Addenda to CSD-1-1998 Controls and Safety Devices for Automatically Fired Boilers Errata - May 2000 ASME FAP-1 Quality Assurance Program Requirements for Fastener Manufacturers, Distributors, and Testing Laboratories ASME HPS High Pressure Systems ASME HPS-A Addenda to HPS-1994 High Pressure Systems ASME HPS-B Addenda to HPS-1994 High Pressure Systems ASME HST-1 Performance Standard for Electric Chain Hoists ASME HST-2 Performance Standard for Hand Chain Manually Operated Chain Hoists ASME HST-3 Performance Standard for Manually Lever Operated Chain Hoists ASME HST-4 Performance Standard for Overhead Electric Wire Rope Hoists ASME HST-5 Performance Standard for Air Chain Hoists ASME HST-6 Performance Standard for Air Wire Rope Hoists ASME MFC-1M Glossary of Terms Used in the Measurement of Fluid Flow in Pipes R(1997) ASME MFC-2M Measurement Uncertainty for Fluid Flow in Closed Conduits R(1988) ASME MFC-3M Measurement of Fluid Flow in Pipes Using Orifice, Nozzle, and Venturi Errata September 1990 R(1995) ASME MFC-4M Measurement of Gas Flow by Turbine Meters R(1997) ASME MFC-5M Measurement of Liquid Flow in Closed Conduits Using Transit-Time Ultrasonic Flowmeters R(1994) ASME MFC-6M Measurement of Fluid Flow in Pipes Using Vortex Flowmeters ASME MFC-7M Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles R(1992) ASME MFC-8M Fluid Flow in Closed Conduits - Connections for Pressure Signal Transmissions Between Primary and Secondary Devices ASME MFC-9M Measurement of Liquid Flow in Closed Conduits by Weighing Methods Errata December 1989 ASME MFC-10M Method for Establishing Installation Effects on Flowmeters ASME MFC-10M (Pending) Method for Establishing Installation Effects on Flowmeters Comment Period Ends: 2000-09-26 ASME MFC-11M Measurement of Fluid Flow by Means of Coriolis Mass Flowmeters R(1994) ASME MFC-14M Measurement of Fluid Flow Using Small Bore Precision Orifice Meters ASME MFC-16M Measurement of Fluid Flow In Closed Conduits by Means of Electromagnetic Flowmeters ASME MH1 Pallets, Slip Sheets, and Other Bases for Unit Loads Supersedes MH1.1.2, MH1.4.1M, MH1.6, and MH1.7M ASME MH1.2.2M Pallet Sizes Revision of ANSI MH1.2.2-1975 ASME MH1.5M Slip Sheets ASME MH1.8M Wood Pallets ASME MH1.9 Export Pallets ASME MH1A Addenda to MH1 - 1997 Pallets, Slip Sheets, and Other Bases for Unit Loads ASME MH5.1.1M (Withdrawn) Requirements for Closed Van Cargo Containers Errata - October 1979, Errata - February 1980, Errata - March 1980, Errata - August 1981

ASME N278.1 Self-Operated and Power-Operated Safety-Related Valves Functional Specification Standard, Reactor Plants and Their Maintenance R(1992) ASME N509 Nuclear Power Plant Air-Cleaning Units and Components Errata - July 1993 R(1996) ASME N509 INTERPRETATIONS Interpretations to N509-1989 Nuclear Power Plant Air-Cleaning Units and Components ASME N510 Testing of Nuclear Air Treatment Systems Errata - 1991 R(1995) ASME N626.0 Qualifications and Duties for Authorized Inspection Agencies, Nuclear Inspectors, and Nuclear Inspector Supervisors ASME N626.1 Qualifications and Duties for Authorized Inspection Agencies, Nuclear Inservice Inspectors, and Nuclear Inservice Inspector Supervisors ASME N626.2 Qualifications and Duties for Authorized Inspection Agencies, Nuclear Inspectors (Concrete), and Nuclear Inspector Supervisors (Concrete) ASME N626.3 Qualifications and Duties of Specialized Professional Engineers ASME N626A Addenda to N626-1990 Qualifications and Duties for Authorized Nuclear Inspection Agencies and Personnel (Revised and Replaced by QAI-1) ASME NOG-1 Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder) ASME NOG-1A Addenda to NOG-1 Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder) ASME NQA-1 1997 EDITION Quality Assurance Requirements for Nuclear Facility Applications ASME NQA-1 2000 EDITION ASME NQA-1A Addenda to NQA-1 - 1997 Edition Quality Assurance Requirements for Nuclear Facility Applications ASME NQA-1A ASME NQA TECH REPT Comparison of ASME NQA-1 and ISO 9001 ASME NUM-1 Rules for Construction of Cranes, Monorails, and Hoists (with Bridge or Trolley or Hoist of the Underhung Type) ASME OHAI MARCH 2000 Organizations Holding Authorized Inspection Agency Certificates of Accreditation ASME OHAI MARCH 2001 ASME OM CODE Code for Operation and Maintenance of Nuclear Power Plants ASME OM CODE CASES Code Cases to OM CODE Code for Operation and Maintenance of Nuclear Power Plants ASME OM CODE INTERPRETATIONS Interpretations to OM CODE-1998 Code for Operation and Maintenance of Nuclear Power Plants ASME OMA CODE Addenda to OM Code - 1998 Code for Operation and Maintenance of Nuclear Power Plants ASME OMA-S/G Addenda to OM-S/G - 1998 Standards and Guides for Operation and Maintenance of Nuclear Power Plants ASME OMB-S/G Addenda to OM-S/G - 1997 Standards and Guides for Operation and Maintenance of Nuclear Power Plants ASME PALD Safety Standard for Portable Automotive Lifting Devices ASME PALD-A Addenda to PLAD-1997 Safety Standard for Portable Automotive Lifting Devices ASME PALD INTERPRETATIONS Interpretations to PALD-1997 Safety Standard for Portable

Automotive Lifting Devices ASME PVHO-1 Safety Standard for Pressure Vessels for Human Occupancy ASME PVHO-1 INTERPRETATIONS Interpretations to PVHO-1997 Safety Standard for Pressure Vessels for Human Occupancy ASME PVHO-1 INTERPRETATIONS ASME PVHO-1A Addenda to BPVH-1-1997 Safety Standard for Pressure Vessels for Human Occupancy ASME QAI-1 Qualifications for Authorized Inspection Revision of N626-1990 ASME QAI-1 INTERPRETATIONS Interpretations to QAI-1-1995 Qualifications for Authorized Inspection ASME QAI-1A Addenda to QAI-1-1995 Qualifications for Authorized Inspection ASME QAI-1B Addenda to QAI-1-1995 Qualifications for Authorized Inspection ASME QEI-1 Standard for the Qualification of Elevator Inspectors ASME QEI-1 ASME QEI-1 (Pending) Standard for the Qualification of Elevator Inspectors Comment Period Ends: 2000-08-15 ASME QEI-1 INTERPRETATIONS Interpretations to ASME QEI-1-1997 ASME QEI-1A Addenda to AMSE QEI-1-1997 Standard for the Qualification of Elevator Inspectors ASME QFO-1 Standard for the Qualification and Certification of Operators of High Capacity Fossil Fuel Fired Plants ASME QHO-1 Qualification and Certification of Hazardous Waste Incinerator Operators ASME QHO-1A Addenda to QHO-1 - 1994 Standard for the Qualification and Certification of Hazardous Waste Incinerator Operators ASME QME-1 Qualification of Active Mechanical Equipment Used in Nuclear Power Plants ASME QME-1A Addenda to QME-1 - 1997 Qualification of Active Mechanical Equipment Used in Nuclear Power Plants ASME QMO-1 Qualification of Medical Waste Incinerator Operators ASME QMO-1 (Pending) Qualification of Medical Waste Incinerator Operators Comment Period Ends: 2000-09-12 ASME QRO-1 Qualification and Certification of Resource Recovery Facility Operators ASME QRO-1 ASME QRO-1A Addenda to QRO-1 - 1994 Standard for the Qualification and Certification of Resource Recovery Facility Operators ASME QRO-1B Addenda to QRO-1 - 1994 Standard for the Qualification and Certification of Resource Recovery Facility Operators ASME RTP-1 Reinforced Thermoset Plastic Corrosion Resistant Equipment ASME RTP-1 INTERPRETATIONS Interpretations to RTP-1-1995 Reinforced Thermoset Plastic Corrosion Resistant Equipment ASME RTP-1A Addenda to RTP-1-1995 Reinforced Thermoset Plastic Corrosion Resistant Equipment ASME RTP-1B Addenda to RTP-1-1995 Reinforced Thermoset Plastic Corrosion Resistant Equipment ASME RTP-1C Addenda to RTP-1-1995 Reinforced Thermoset Plastic Corrosion Resistant Equipment ASME RTP-1D Addenda to RTP-1 - 1995 Edition Reinforced Thermoset Plastic Corrosion Resistant Equipment ASME RTP-1E Addenda to RTP-1 - 1995 Edition Reinforced Thermoset Plastic Corrosion Resistant Equipment

ASME SI-1 Orientation and Guide for Use of SI (Metric) Units ASME SPPE-1 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME SPPE-1A Addenda to SPPE-1-1994 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME SPPE-1B Addenda to SPPE-1-1994 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME SPPE-1C Addenda to SPPE-1-1994 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME SPPE-1D Addenda to SPPE-1-1994 Quality Assurance and Certification of Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME SPPE-2 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME SPPE-2A Addenda to SPPE-2-1994 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME SPPE-2B Addenda to SPPE-2-1994 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME SPPE-2C Addenda to SPPE-2-1994 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME SPPE-2D Addenda to SPPE-2-1994 Accreditation of Testing Laboratories for Safety and Pollution Prevention Equipment Used in Offshore Oil and Gas Operations ASME STS-1 Steel Stacks ASME TDP-1 Recommended Practices for the Prevention of Water Damage to Steam Turbines Used for Electric Power Generation

2006

2007-03-25 20:33

ASME Y10.1 Glossary of Terms Concerning Letter Symbols R(1988) ASME Y10.1 ASME Y10.11 Letter Symbols and Abbreviations for Quantities Used in Acoustics Revision of ASA Y10.11-53 ASME Y10.18 Letter Symbols for Illuminating Engineering R(1987) ASME Y14.1 Decimal Inch Drawing Sheet Size and Format ASME Y14.1M Metric Drawing Sheet Size and Format ASME Y14.2M Line Conventions and Lettering ASME Y14.2M ASME Y14.3M Multiand Sectional Drawings Revision of ANSI Y14.3 - 1975 R(1999) ASME Y14.4M Pictorial Drawing R(1999) ASME Y14.5.1M Mathematical Definition of Dimensioning and Tolerancing Principles R(1999) ASME Y14.5.2 Certification of Geometric Dimensioning and Tolerancing Professionals ASME Y14.5M Dimensioning and Tolerancing R(1999) ASME Y14.5M-1982 (HISTORICAL) DIMENSIONING AND TOLERANCING; ERRATA - FEBRUARY 1985 (R 1988) ASME Y14.6 (Pending) Screw Thread Representation Comment Period Ends: 2000-09-12

ASME Y14.6 Screw Thread Representation R(1998) ASME Y14.6AM Screw Thread Representation Metric Supplement to ANSI Y14.6-78 R(1998) ASME Y14.7.1 Gear Drawing Standards - Part 1 for Spur, Helical, Double Helical and Rack Partial Revision of Y14.7-58 R(1998) ASME Y14.7.2 Gear and Spline Drawing Standards Part 2 - Bevel and Hypoid Gears R(1999) ASME Y14.8M Castings and Forgings ASME Y14.13M Mechanical Spring Representation R(1998) ASME Y14.18M Optical Parts R(1998) ASME Y14.24 Types and Applications of Engineering Drawings Revision of ASME Y14.24M-1989 ASME Y14.26M Digital Representation for Communication of Product Definition Data ASME Y14.26M ASME Y14.32.1M Chassis Frames - Passenger Car and Light Truck - Ground Vechicle Practices R(1999) ASME Y14.34M Associated Lists ASME Y14.35M Revision of Engineering Drawings and Associated Documents ASME Y14.36M Surface Texture Symbols ASME Y14.38 Abbreviations and Acronyms Revision and Redesignation of ASME Y1.1-1989 ASME Y14.100M Engineering Drawing Practices ASME Y14 REPORT Digital Representation of Physical Object Shapes ASME Y14 REPORT ASME Y14 REPORT 3 Guideline for Documenting of Computer Systems Used in Computer-Aided Preparation of Product Definition Data Design Requirements ASME Y14 TECH REPT 4 Structural Language Format for Basic Shape Description ASME Y32.2.3 Graphical Symbols for Pipe Fittings, Valves, and Piping Redesignation of Z32.2.3-49(1953) R(1999) ASME Y32.2.4 Graphical Symbols for Heating, Ventilating, and Air Conditioning Redesignation of Z32.2.4-49 R(1998) ASME Y32.2.6 Graphical Symbols for Heat-Power Apparatus Redesignation of Z32.2.6-50 R(1999) ASME Y32.4 Graphic Symbols for Plumbing Fixtures for Diagrams Used in Architecture and Building Construction Revision of ANSI Y32.4-54 R(1999) ASME Y32.7 Graphic Symbols for Railroad Maps and Profiles Revision of ANSI Y32.7-57 R(1994) ASME Y32.10 Graphic Symbols for Fluid Power Diagrams R(1999) ASME Y32.11 Graphical Symbols for Process Flow Diagrams in the Petroleum and Chemical Industries R(1998) ASME Y32.18 Symbols for Mechanical and Acoustical Elements as Used in Schematic Diagrams R(1998) ASME AIA MARCH-99 Organizations Holding Authorized Inspection Agency Certificates of Accreditation ASME CHAN MARCH-96 Companies Holding Authorized Nuclear Inspection Agency Certificates of Accreditation ASME FAP MARCH-98 Companies Holding FAP Certificates of Accreditation ASME NUC NOVEMBER 2000 Companies Holding Nuclear Certificates ASME NUC MARCH 2001 ASME PVHO MARCH-94 Companies Holding PVHO Certificates of Authorization

ASME QEI MARCH-99 Companies Holding QEI Certificates of Accreditation ASME QEI MARCH-01 ASME QRO MARCH-99 Individuals Holding QRO Certificates of Certification ASME RTP MARCH-00 Companies Holding RTP Certificates of Authorization ASME RTP MARCH-01 ASME SPPE MARCH-98 Companies Holding SPPE Certificates of Authorization (for Use of the OCS Stamp) and Certificates of Accreditation ASME PTC 1 General Instructions (Performance Test Codes) ASME PTC 2 Definitions and Values (Performance Test Codes) R(1985) ASME PTC 3.1 Diesel and Burner Fuels (Performance Test Codes) R(1992) ASME PTC 3.2 Coal and Coke (Performance Test Codes) ASME PTC 3.3 Gaseous Fuels (Performance Test Codes) R(1992) ASME PTC 4 Fire Steam Generators Revision of ASME PTC 4.1-1964(R1991) (Performance Test Codes) ASME PTC 4.2 Coal Pulverizers (Performance Test Codes) R(1997) ASME PTC 4.3 Air Heaters (Performance Test Codes) R(1991) ASME PTC 4.4 Gas Turbine Heat Recovery Steam Generators (Performance Test Codes) R(1992) ASME PTC 5 Reciprocating Steam Engines (Performance Test Codes) ASME PTC 6 Steam Turbines (Performance Test Codes) ASME PTC 6 INT 1977-1983- INTERPRETATIONS TO STEAM TURBINES ASME PTC 6 REPORT Guidance for Evaluation of Measurement Uncertainty in Performance Tests of Steam Turbines R(1997) ASME PTC 6A Appendix A To Test Code for Steam Turbines; Errata - 1988 (R 1995) ASME PTC 6A (Pending) Appendix To PTC 6 - Test Code for Steam Turbines Comkment Period Ends: 2000-09-12 ASME PTC 6S-70 REPORT SIMPLIFIED PROCEDURES FOR ROUTINE PERFORMANCE TESTS OF STEAM TURBINES (R 1985) ASME PTC 6S REPORT Procedures for Routine Performance Tests of Steam Turbines (R 1995) ASME PTC 7.1 Displacement Pumps (Performance Test Codes) R(1969) ASME PTC 8.2 Centrifugal Pumps (Performance Test Codes) ASME PTC 9 Displacement Compressors, Vacuum Pumps and Blowers Erratum - 1972 (Performance Test Codes) R(1997) ASME PTC 11 Fans (Performance Test Codes) R(1995) ASME PTC 11 ASME PTC 12.2 Performance Test Code on Steam Surface Condensers (Performance Test Codes) R(1988) ASME PTC 12.2 ASME PTC 12.3 Performance Test Code on Deaerators (Performance Test Codes) ASME PTC 12.3 ASME PTC 12.4 Moisture Separator Reheaters R(1997) ASME PTC 12.5 (Pending) Single Phase Heat Exchangers Comment Period Ends: 2000-08-15 ASME PTC 17 Reciprocating Internal-Combustion Engines (Performance Test Codes) R(1997) ASME PTC 18 Hydraulic Turbines (Performance Test Codes) ASME PTC 18.1 Pumping Mode of Pump/Turbines (Performance Test Codes) R(1984)

ASME PTC 19.1 Test Uncertainty Instruments and Apparatus (Performance Test Codes) ASME PTC 19.2 Part 2: Pressure Measurement Instruments and Apparatus (Performance Test Codes) R(1998) ASME PTC 19.2 ASME PTC 19.3 Part 3: Temperature Measurement Instruments and Apparatus (Performance Test Codes) R(1998) ASME PTC 19.5 Application Part II of Fluid Meters (Performance Test Codes) ASME PTC 19.5 ASME PTC 19.5.1 Chapter 1: Weighing Scales Part 5: Measurement of Quantity of Materials Instruments and Apparatus (Performance Test Codes) ASME PTC 19.7 Part 7: Measurement of Shaft Power Instruments and Apparatus (Performance Test Codes) R(1988) ASME PTC 19.8 Part 8: Measurement of Indicated Power Instruments and Apparatus (Performance Test Codes) R(1985) ASME PTC 19.10 Part 10: Flue and Exhaust Gas Analyses Instruments and Apparatus (Performance Test Codes) ASME PTC 19.10 ASME PTC 19.11 Steam and Water Sampling, Conditioning, and Analysis in the Power Cycle (Performance Test Codes) ASME PTC 19.11 ASME PTC 19.14 Part 14: Linear Measurements Instruments and Apparatus (Performance Test Codes) ASME PTC 19.14 ASME PTC 19.22 Part 22: Digital Systems Techniques Instruments and Apparatus (Performance Test Codes) R(1998) ASME PTC 19.22 ASME PTC 19.23 Part 23: Guidance Manual for Model Testing Instruments and Apparatus (Performance Test Codes) R(1985) ASME PTC 19.23 ASME PTC 20.1 Speed and Load Governing Systems for Steam Turbine-Generator Units (Performance Test Codes) R(1988) ASME PTC 20.1 ASME PTC 20.2 Overspeed Trip Systems for Steam Turbine-Generator Units (Performance Test Codes) R(1986) ASME PTC 20.3 Pressure Control Systems Used on Steam Turbine-Generator Units (Performance Test Codes) R(1986) ASME PTC 21 Particulate Matter Collection Equipment (Performance Test Codes) ASME PTC 21 ASME PTC 22 Performance Test Code on Gas Turbines (Performance Test Codes) ASME PTC 23 Atmospheric Water Cooling Equipment (Performance Test Codes) R(1997) ASME PTC 24 Ejectors (Performance Test Codes) R(1982) ASME PTC 25 Pressure Relief Devices ASME PTC 25 SPECIAL ADDENDA Special Addenda to PTC 25-1994 Pressure Relief Devices ASME PTC 26 Speed-Governing Systems for Internal Combustion Engine-Generator Units (Performance Test Codes)

ASME PTC 28 Determining the Properties of Fine Particulate Matter (Performance Test Codes) R(1985) ASME PTC 29 Speed-Governing Systems for Hydraulic Turbine-Generator Units (Performance Test Codes) R(1985) ASME PTC 30 Air Cooled Heat Exchangers R(1998) ASME PTC 31 Ion Exchange Equipment (Performance Test Codes) R(1991) ASME PTC 32.1 Nuclear Steam Supply Systems (Performance Test Codes) R(1992) ASME PTC 33 Large Incinerators Appendix 33A-1980 (Performance Test Codes) R(1991) ASME PTC 36 Measurement of Industrial Sound (Performance Test Codes) R(1998) ASME PTC 38 Determining the Concentration of Particulate Matter in a Gas Stream (Performance Test Codes) R(1985) ASME PTC 39.1 Condensate Removal Devices for Steam Systems (Performance Test Codes) R(1991) ASME PTC 40 Flue Gas Desulfurization Units ASME PTC 42 Wind Turbines R(1998) ASME PTC 46 Performance Test Code on Overall Plant Performance ASME PTC PM Performance Monitoring Guidelines for Steam Power Plants ASME CC N1 SUPPLEMENT 4 BPVC 1998 Code Cases Nuclear Components Supplement 4; Non-Interfiled ASME SEC I BPVC SECTION I Rules for Construction of Power Boilers Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC I ADD BPVC SECTION I 1999 Addenda, Rules for Construction of Power Boilers Non-Interfiled ASME SEC II-A BPVC SECTION II Materials Part A - Ferrous Material Specifications Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC II-A ADD BPVC SECTION II 1999 Addenda, Materials Part A - Ferrous Material Specifications Non-Interfiled ASME SEC II-B BPVC SECTION II Materials Part B - Nonferrous Material Specifications Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC II-B ADD BPVC SECTION II Materials Part B - Nonferrous Material Specifications Non-Interfiled ASME SEC II-C BPVC SECTION II Materials Part C - Specifications for Welding Rods, Electrodes, and Filler Metals Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC II-C ADD BPVC SECTION II 1999 Addenda, Materials Part C - Specifications for Welding Rods, Electrodes, and Filler Metals Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC II-D BPVC SECTION II Materials Part D - Properties Non-Interfiled ASME SEC II-D ADD BPVC SECTION II 1999 Addenda, Materials Part D - Properties Non-Interfiled ASME SEC III NCA BPVC SECTION III Rules for Construction of Nuclear Power Plant Components SUBSECTION NCA General Requirements for DIVISION 1 and DIVISION 2 ACI 359:1998; Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III NCA ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components SUBSECTION NCA General Requirements for DIVISION 1 and DIVISION 2 ACI 359:1998; Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 NB BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NB Class 1 Components Non-Interfiled ASME SEC III D1 NB ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility

Components DIVISION 1 - SUBSECTION NB Class 1 Components Non-Interfiled ASME SEC III D1 NC BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NC Class 2 Components Non-Interfiled ASME SEC III D1 NC ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NC Class 2 Components Non-Interfiled ASME SEC III D1 ND BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION ND Class 3 Components Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 ND ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION ND Class 3 Components Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 NE BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NE Class MC Components Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 NE ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NE Class MC Components Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 NF BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NF Supports Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 NF ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NF Supports Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 NG BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NG Core Support Structures Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 NG ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NG Core Support Structures Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 NH BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - SUBSECTION NH Class 1 Components in Elevated Temperature Service Non-Interfiled ASME SEC III D1 NH ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - SUBSECTION NH Class 1 Components in Elevated Temperature Service Non-Interfiled ASME SEC III D1 APPENDICES BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 1 - APPENDICES Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III D1 APPENDICES ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 1 - APPENDICES Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC III DIVISION 2 BPVC SECTION III Rules for Construction of Nuclear Power Plant Components DIVISION 2: Code for Concrete Reactor Vessels and Containments ACI 359-98; Non-Interfiled ASME SEC III D2 ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 2: Code for Concrete Reactor Vessels and Containments ACI 359-98; Non-Interfiled ASME SEC III DIVISION 3 BPVC SECTION III Rules for Construction of Nuclear Power Plant

Components DIVISION 3: Containment Systems and Transport Packagings for Spent Nuclear Fuel and High Level Radioactive Waste Non-Interfiled ASME SEC III D3 ADD BPVC SECTION III 1999 Addenda, Rules for Construction of Nuclear Facility Components DIVISION 3: Containment Systems for Storage and Transport Packagings of Spent Nuclear Fuel and High Level Radioactive Material and Waste Non-Interfiled ASME SEC IV BPVC SECTION IV Rules for Construction of Heating Boilers Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC IV ADD BPVC SECTION IV 1999 Addenda, Rules for Construction of Heating Boilers Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC V BPVC SECTION V Nondestructive Examination Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC V ADD BPVC SECTION V 1999 Addenda, Nondestructive Examination Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VI BPVC SECTION VI Recommended Rules for the Care and Operation of Heating Boilers Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VI ADD BPVC SECTION VI 1999 Addenda Recommended Rules for the Care and Operation of Heating Boilers Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VII BPVC SECTION VII Recommended Guidelines for the Care of Power Boilers Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VII ADD BPVC SECTION VII 1999 Addenda Recommended Guidelines for the Care of Power Boilers Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VIII DIVISION 1 BPVC SECTION VIII Rules for Construction of Pressure Vessels DIVISION 1 Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VIII D1 ADD BPVC SECTION VIII 1999 Addenda, Rules for Construction of Pressure Vessels DIVISION 1 Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VIII DIVISION 2 BPVC SECTION VIII Rules for Construction of Pressure Vessels DIVISION 2 - Alternative Rules Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VIII D2 ADD BPVC SECTION VIII 1999 Addenda, Rules for Construction of Pressure Vessels DIVISION 2 - Alternative Rules Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VIII DIVISION 3 BPVC SECTION VIII Rules for Construction of Pressure Vessels DIVISION 3 - Alternative Rules for High Pressure Vessels Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC VIII D3 ADD BPVC SECTION VIII 1999 Addenda, Rules for Construction of Pressure Vessels DIVISION 3 - Alternative Rules for Construction of High Pressure Vessels Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC IX BPVC SECTION IX Welding and Brazing Qualifications Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC IX ADD BPVC SECTION IX 1999 Addenda, Qualification Standard for Welding and Brazing Procedures, Welders, Brazers, and Welding and Brazing Operators Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC X BPVC SECTION X Fiber-Reinforced Plastic Pressure Vessels Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC X ADD BPVC SECTION X 1999 Addenda, Fiber-Reinforced Plastic Pressure Vessels Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC XI BPVC SECTION XI Rules for Inservice Inspection of Nuclear Power Plant Components

Non-Interfiled (Boiler and Pressure Vessel Codes) ASME SEC XI ADD BPVC SECTION XI 1999 Addenda, Rules for Inservice Inspection of Nuclear Power Plant Components Non-Interfiled (Boiler and Pressure Vessel Codes) ASME CC B1 BPVC 1998 Code Cases Boilers and Pressure Vessels Non-Interfiled ASME CC B1 SUPPLEMENT 1 BPVC 1998 Code Cases Boilers and Pressure Vessels Supplement 1; Non-Interfiled ASME CC B1 SUPPLEMENT 2 BPVC 1998 Code Cases Boilers and Pressure Vessels Supplement 2; Non-Interfiled ASME CC B1 SUPPLEMENT 3 BPVC 1998 Code Cases Boilers and Pressure Vessels Supplement 3; Non-Interfiled ASME CC B1 SUPPLEMENT 4 BPVC 1998 Code Cases Boilers and Pressure Vessels Supplement 4; Non-Interfiled ASME CC N1 BPVC 1998 Code Cases Nuclear Components Non-Interfiled ASME CC N1 SUPPLEMENT 1 BPVC 1998 Code Cases Nuclear Components Supplement 1; Non-Interfiled ASME CC N1 SUPPLEMENT 2 BPVC 1998 Code Cases Nuclear Components Supplement 2; Non-Interfiled ASME CC N1 SUPPLEMENT 3 BPVC 1998 Code Cases Nuclear Components Supplement 3; Non-Interfiled ASME SEC I INT VOL 42 Interpretations Volume 42 ASME SEC I INT VOL 44 Interpretations Volume 44 ASME SEC I INT VOL 43 Interpretations Volume 43 ASME SEC II-A INT VOL 42 Interpretations Volume 42 ASME SEC II-A INT VOL 44 Interpretations Volume 44 ASME SEC III D1 INT VOL 42 Interpretations Volume 42 ASME SEC III D1 INT VOL 43 Interpretations Volume 43 ASME SEC III D1 INT VOL 44 Interpretations Volume 44 ASME SEC III D2 INT VOL 42 Interpretations Volume 42 ASME SEC III D2 INT VOL 43 Interpretations Volume 43 ASME SEC III D2 INT VOL 44 Interpretations Volume 44 ASME SEC IV INT VOL 42 Interpretations Volume 42 ASME SEC IV INT VOL 43 Interpretations Volume 43 ASME SEC IV INT VOL 44 Interpretations Volume 44 ASME SEC V INT VOL 42 Interpretations Volume 42 ASME SEC V INT VOL 43 Interpretations Volume 43 ASME SEC V INT VOL 44 Interpretations Volume 44 ASME SEC VIII D1 INT VOL 42 Interpretations Volume 42 ASME SEC VIII D1 INT VOL 43 Interpretations Volume 43 ASME SEC VIII D1 INT VOL 44 Interpretations Volume 44 ASME SEC VIII D2 INT VOL 42 Interpretations Volume 42 ASME SEC VIII D2 INT VOL 43 Interpretations Volume 43 ASME SEC VIII D2 INT VOL 44 Interpretations Volume 44 ASME SEC VIII D3 INT VOL 43 Interpretations Volume 43 ASME SEC IX INT VOL 42 Interpretations Volume 42

ASME SEC IX INT VOL 43 Interpretations Volume 43 ASME SEC IX INT VOL 44 Interpretations Volume 44 ASME SEC XI INT VOL 42 Interpretations Volume 42 ASME SEC XI INT VOL 43 Interpretations Volume 43 ASME SEC XI INT VOL 44 Interpretations Volume 44 ASME SEC I A2000 2000 Addenda Summary of Changes ASME SEC I A99 1999 Addenda Summary of Changes ASME SEC I A98 1998 Addenda Summary of Changes ASME SEC I INTRODUCTION Introduction ASME SEC I PT PG Part PG General Requirements for All Methods of Construction ASME SEC I PT PW Part PW Requirements for Boilers Fabricated by Welding ASME SEC I PT PR Part PR Requirements for Boilers Fabricated by Riveting Interfiled ASME SEC I PT PB Part PB Requirements for Boilers Fabricated by Brazing Interfiled ASME SEC I PT PWT Part PWT Requirements for Watertube Boilers ASME SEC I PT PFT Part PFT Requirements for Firetube Boilers ASME SEC I PT PFH Part PFH Optional Requirements for Feedwater Heater (When Located within Scope of Section I Rules) Interfiled ASME SEC I PT PMB Part PMB Requirements for Miniature Boilers ASME SEC I PT PEB Part PEB Requirements for Electric Boilers ASME SEC I PT PVG Part PVG Requirements for Organic Fluid Vaporizers Interfiled ASME SEC I MA I Appendix I - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee Interfiled ASME SEC I NMA A Appendix A Explanation of the Code Containing Matter Not Mandatory Unless Specifically Referred to in the Rules of the Code ASME SEC I FORMS/GUIDES Data Report Forms and Guides ASME SEC I CODES Codes, Standards, and Specifications Referenced in Text ASME SEC I SI UNITS SI Units Interfiled ASME SEC I INDEX Index ASME SEC II A SA-995 SA-995 Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing Parts ASTM A 995-98 ASME SEC II A A99 1999 Addenda Summary of Changes ASME SEC II A A2000 2000 Addenda Summary of Changes ASME SEC II A A98 1998 Addenda Summary of Changes ASME SEC II A INTRODUCTION Introduction ASME SEC II A MA APP 1 Appendix 1 - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee ASME SEC II A NMA APP A Appendix A - Nonmandatory Acceptable ASTM Editions ASME SEC II A NMA APP B Appendix B Nonmandatory Guidelines on Multiple Marking of Materials ASME SEC II A SI SI Units ASME SEC II A SA-6/SA-6M SA-6/SA-6M Specification for General Requirements for Rolled Steel Plates, Shapes, Sheet Piling, and Bars for Structural Use ASTM A 6/A 6M-93b ASME SEC II A SA-20/SA-20M SA-20/SA-20M Specification for General Requirements for Steel Plates for Pressure Vessels ASTM A 20/A 20M-93a ASME SEC II A SA-29/SA-29M SA-29/SA-29M Specification for Steel Bars, Carbon and Alloy,

Hot-Wrought and Cold-Finished, General Requirements for ASTM A 29/A 29M-93a ASME SEC II A SA-36/SA-36M SA-36/SA-36M Specification for Carbon Structural Steel ASTM A 36/A 36M-96 ASME SEC II A SA-47 SA-47 Specification for Ferritic Malleable Iron Castings ASTM A 47-90 ASME SEC II A SA-53 SA-53 Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless ASTM A 53-96 ASME SEC II A SA-105/SA-105M SA-105/SA-105M Specification for Carbon Steel Forgings for Piping Applications ASTM A 105/A 105M-96 ASME SEC II A SA-106 SA-106 Specification for Seamless Carbon Steel Pipe for High-Temperature Service ASTM A 106-95 ASME SEC II A SA-134 SA-134 Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and over) ASTM A 134-93 ASME SEC II A SA-135 SA-135 Specification for Electric-Resistance-Welded Steel Pipe ASTM A 135-96 ASME SEC II A SA-178/SA-178M SA-178/SA-178M Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheated Tubes ASTM A 178/A 178M-95 ASME SEC II A SA-179/SA-179M SA-179/SA-179M Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes ASTM A 179/A 179M-90a ASME SEC II A SA-181/SA-181M SA-181/SA-181M Specification for Carbon Steel Forgings, for General-Purpose Piping ASTM A 181/A 181M-95b ASME SEC II A SA-182/SA-182M SA-182/SA-182M Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service ASTM A 182/A 182M-98 ASME SEC II A SA-192/SA-192M SA-192/SA-192M Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service ASME SEC II A SA-193/SA-193M SA-193/SA-193M Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service ASTM A 193/A 193M-98a ASME SEC II A SA-194/SA-194M SA-194/SA-194M Specification for Carbon and Alloy Steel Nuts for Bolts for High-Pressure and High-Temperature Service ASTM A 194/A 194M-95a ASME SEC II A SA-199/SA-199M SA-199/SA-199M Specification for Seamless Cold-Drawn Intermediate Alloy-Steel Heat-Exchanger and Condenser Tubes ASTM A 199/A 199M-92 ASME SEC II A SA-202/SA-202M SA-202/SA-202M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-Silicon ASTM A 202/A 202M-93 ASME SEC II A SA-203/SA-203M SA-203/SA-203M Specification for Pressure Vessel Plates, Alloy Steel, Nickel ASTM A 203/A 203M-93 ASME SEC II A SA-204/SA-204M SA-204/SA-204M Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum ASTM A 204/A 204M-93 ASME SEC II A SA-209/SA-209M SA-209/SA-209M Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes ASTM A 209/A 209M-95 ASME SEC II A SA-210/SA-210M SA-210/SA-210M Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes ASTM A 210/A 210M-95 ASME SEC II A SA-213/SA-213M SA-213/SA-213M Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes ASTM A 213/A 213M-95a ASME SEC II A SA-214/SA-214M SA-214/SA-214M Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes ASTM A 214/A 214M-90a ASME SEC II A SA-216/SA-216M SA-216/SA-216M Specification for Steel Castings, Carbon, Suitable

for Fusion Welding for High-Temperature Service ASTM A 216/A 216M-93 ASME SEC II A SA-217/SA-217M SA-217/SA-217M Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service ASTM A 217/A 217M-93 ASME SEC II A SA-225/SA-225M SA-225/SA-225M Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-Nickel ASTM A 225/A 225M-93 ASME SEC II A SA-226/SA-226M SA-226/SA-226M Specification for Electric-Resistance-Welded Carbon Steel Boiler and Superheater Tubes for High-Pressure Service ASTM A 226/A 226M-95 ASME SEC II A SA-232/SA-232M SA-232/SA-232M Specification for Chromium-Vanadium Alloy Steel Valve Spring Quality Wire ASTM A 232/A 232M-91 ASME SEC II A SA-234/SA-234M SA-234/SA-234M Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and Elevated Temperatures ASTM A 234/A 234M-95a ASME SEC II A SA-240 SA-240 Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels ASTM A 240-97a ASME SEC II A SA-249/SA-249M SA-249/SA-249M Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes ASTM A 249/A 249M-96a ASME SEC II A SA-250/SA-250M SA-250/SA-250M Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater Tubes ASTM A 250/A 250M-95 ASME SEC II A SA-263 SA-263 Specification for Corrosion-Resisting Chromium Steel-Clad Plate, Sheet, and Strip ASTM A 263-94 ASME SEC II A SA-264 SA-264 Specification for Stainless Chromium-Nickel Steel-Clad Plate, Sheet, and Strip ASTM A 264-94a ASME SEC II A SA-265 SA-265 Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate ASTM A 265-94a ASME SEC II A SA-266/SA-266M SA-266/SA-266M Specification for Carbon Steel Forgings for Pressure Vessel Components ASTM A 266/A 266M-95 ASME SEC II A SA-268/SA-268M SA-268/SA-268M Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service ASTM A 268/A 268M-94 ASME SEC II A SA-275/SA-275M SA-275/SA-275M Specification for Magnetic Particle Examination of Steel Forgings ASTM A 275/A275M-96 ASME SEC II A SA-278 SA-278 Specification for Gray Iron Castings for Pressure-Containing Parts for Temperatures up to 650 Degrees F ASTM A 278-93 ASME SEC II A SA-283/SA-283M SA-283/SA-283M Specification for Low and Intermediate Tensile Strength Carbon Steel Plates ASTM A 283/A 283M-93 ASME SEC II A SA-285/SA-285M SA-285/SA-285M Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength ASTM A 285/A 285M-90 ASME SEC II A SA-299/SA-299M SA-299/SA-299M Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon ASTM A 299/A 299M-90 ASME SEC II A SA-302/SA-302M SA-302/SA-302M Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel ASTM A 302/A 302M-93 ASME SEC II A SA-307 SA-307 Specification for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength ASTM A 307-93a ASME SEC II A SA-311/SA-311M SA-311/SA-311M Specification for Steel Bars, Carbon, Stress-Relieved Cold-Drawn, Subject to Mechanical Property Requirements ASTM A 311/A 311M-90b

ASME SEC II A SA-312/SA-312M SA-312/SA-312M Specification for Seamless and Welded Austenitic Stainless Steel Pipes ASTM A 312/A 312M-95b ASME SEC II A SA-320/SA-320M SA-320/SA-320M Specification for Alloy Steel Bolting Materials for Low-Temperature Service ASTM A 320/A 320M-94a ASME SEC II A SA-325 SA-325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 KSI Minimum Tensile Strength ASTM A 325-94 ASME SEC II A SA-333/SA-333M SA-333/SA-333M Specification for Seamless and Welded Steel Pipe for Low-Temperature Service ASTM A 333/A 333M-94 ASME SEC II A SA-334/SA-334M SA-334/SA-334M Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service ASTM A 334/A 334M-96 ASME SEC II A SA-335/SA-335M SA-335/SA-335M Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service ASTM A 335/A 335M-95a ASME SEC II A SA-336/SA-336M SA-336/SA-336M Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts ASTM A 336/A 336M-96 ASME SEC II A SA-350/SA-350M SA-350/SA-350M Specification for Forgings, Carbon and Low-Alloy Steel, Requiring Notch Toughness Testing for Piping Components ASTM A 350/A 350M-95b ASME SEC II A SA-351/SA-351M SA-351/SA-351M Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts ASTM A 351/A 351M-94a ASME SEC II A SA-352/SA-352M SA-352/SA-352M Specification for Steel Castings, Ferritic and Martensitic, for Pressure Containing Parts, Suitable for Low Temperature Service ASTM A 352/A 352M-93 ASME SEC II A SA-353/SA-353M SA-353/SA-353M Specification for Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel, Double-Normalized and Tempered ASTM A 353/A 353M-93 ASME SEC II A SA-354 SA-354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners ASTM A 354-95 ASME SEC II A SA-358/SA-358M SA-358/SA-358M Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe for High-Temperature Service ASTM A 358/A 358M-95a ASME SEC II A SA-369/SA-369M SA-369/SA-369M Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service ASTM A 369/A 369M-92 ASME SEC II A SA-370 SA-370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products ASTM A 370-96 ASME SEC II A SA-372/SA-372M SA-372/SA-372M Specification for Carbon and Alloy Steel Forgings for Thin-Walled Pressure Vessels ASTM A 372/A 372M-95 ASME SEC II A SA-376/SA-376M SA-376/SA-376M Specification for Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service ASTM A 376/A 376M-93 ASME SEC II A SA-387/SA-387M SA-387/SA-387M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum ASTM A 387/A 387M-92 E1 ASME SEC II A SA-388/SA-388M SA-388/SA-388M Specification for Ultrasonic Examination of Heavy Steel Forgings ASTM A 388/A 388M-95 ASME SEC II A SA-395 SA-395 Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures ASTM A 395-88 (Reapproved 1993) E1 ASME SEC II A SA-403/SA-403M SA-403/SA-403M Specification for Wrought Austenitic Stainless Steel Piping Fittings ASTM A 403/A 403M-95 ASME SEC II A SA-409/SA-409M SA-409/SA-409M Specification for Welded Large Diameter

Austenitic Steel Pipe for Corrosive or High-Temperature Service ASTM A 409/A 409M-95a E1 ASME SEC II A SA-420/SA-420M SA-420/SA-420M Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service ASTM A 420/A 420M-95 ASME SEC II A SA-423/SA-423M SA-423/SA-423M Specification for Seamless and Electric-Welded Low-Alloy Steel Tubes ASTM A 423/A 423M-95 ASME SEC II A SA-414/SA-414M SA-414/SA-414M Specification for Steel, Sheet, Carbon, for Pressure Vessels ASTM A 414/A 414M-92 (R1993) E1 ASME SEC II A SA-426 SA-426 Specification for Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature Service ASTM A 426-92 ASME SEC II A SA-430/SA-430M SA-430/SA-430M Specification for Austenitic Steel Forged and Bored Pipe for High-Temperature Service ASTM A 430/A 430M-91 ASME SEC II A SA-435/SA-435M SA-435/SA-435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates ASTM A 435/A 435M-90 ASME SEC II A SA-437/SA-437M SA-437/SA-437M Specification for Alloy-Steel Turbine-Type Bolting Material Specially Heat Treated for High-Temperature Service ASTM A 437/A 437M-94 ASME SEC II A SA-449 SA-449 Specification for Quenched and Tempered Steel Bolts and Studs ASTM A 449-92b ASME SEC II A SA-450/SA-450M SA-450/SA-450M Specification for General Requirements for Carbon, Ferritic Alloy, and Austenitic Alloy Steel Tubes ASTM A 450/A 450M-96 ASME SEC II A SA-451 SA-451 Specification for Centrifugally Cast Austenitic Steel Pipe for High-Temperature Service ASTM A 451-93 ASME SEC II A SA-452 SA-452 Specification for Centrifugally Cast Austenitic Steel Cold-Wrought Pipe for High-Temperature Service ASTM A 452-88 ASME SEC II A SA-453/SA-453M SA-453/SA-453M Specification for Bolting Materials, High-Temperature, 50 to 120 ksi (345 to 827 MPa) Yield Strength with Expansion Coefficients Comparable to Austenitic Steels ASTM A 453/A 453M-94 ASME SEC II A SA-455/SA-455M SA-455/SA-455M Specification for Pressure Vessel Plates, Carbon Steel, High-Strength Manganese ASTM A 455/A 455M-90 ASME SEC II A SA-476 SA-476 Specification for Ductile Iron Castings for Paper Mill Dryer Rolls ASTM A 476-90 ASME SEC II A SA-479/SA-479M SA-479/SA-479M Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels ASTM A 479/A 479M-95b ASME SEC II A SA-480/SA-480M SA-480/SA-480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip ASTM A 480/A 480M-96 ASME SEC II A SA-484/SA-484M SA-484/SA-484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings ASTM A 484/A 484M-94b ASME SEC II A SA-487/SA-487M SA-487/SA-487M Specification for Steel Castings Suitable for Pressure Service ASTM A 487/A 487M-93 ASME SEC II A SA-494/SA-494M SA-494/SA-494M Specification for Castings, Nickel and Nickel Alloy See Section II, Part B, SA-494/SA-494M ASME SEC II A SA-508/SA-508M SA-508/SA-508M Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels ASTM A 508/A 508M-95 ASME SEC II A SA-515/SA-515M SA-515/SA-515M Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service ASTM A 515/A 515M-92

ASME SEC II A SA-516/SA-516M SA-516/SA-516M Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service ASTM A 516/A 516M-90 ASME SEC II A SA-517/SA-517M SA-517/SA-517M Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered ASTM A 517/A 517M-93 ASME SEC II A SA-522/SA-522M SA-522/SA-522M Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service ASTM A 522/A 522M-95 ASME SEC II A SA-524 SA-524 Specification for Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures ASTM A 524-93 ASME SEC II A SA-530/SA-530M SA-530/SA-530M Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe ASTM A 530/A 530M-96 ASME SEC II A SA-533/SA-533M SA-533/SA-533M Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel ASTM A 533/A 533M-93 ASME SEC II A SA-537/SA-537M SA-537/SA-537M Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel ASTM A 537/A 537M-91 ASME SEC II A SA-540/SA-540M SA-540/SA-540M Specification for Alloy-Steel Bolting Materials for Special Applications ASTM A 540/A 540M-93 ASME SEC II A SA-541/SA-541M SA-541/SA-541M Specification for Quenched and Tempered Carbon and Alloy Steel Forgings for Pressure Vessel Components ASTM A 541/A 541M-95 ASME SEC II A SA-542/SA-542M SA-542/SA-542M Specification for Pressure Vessel Plates, Alloy Steel, Quenched-and-Tempered, Chromium-Molybdenum, and Chromium-Molybdenum-Vanadium ASTM A 542/A 542M-95 ASME SEC II A SA-543/SA-543M SA-543/SA-543M Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Nickel-Chromium-Molybdenum ASTM A 543/A 543M-93 ASME SEC II A SA-553/SA-553M SA-553/SA-553M Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 8 and 9 Percent Nickel ASTM A 553/A 553M-93 ASME SEC II A SA-556/SA-556M SA-556/SA-556M Specification for Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes ASTM A 556/A 556M-90a (Reapproved 1995) E1 ASME SEC II A SA-557/SA-557M SA-557/SA-557M Specification for Electric-Resistance-Welded Carbon Steel Feedwater Heater Tubes ASTM A 557/A 557M-90a ASME SEC II A SA-562/SA-562M SA-562/SA-562M Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic Coatings ASTM A 562/A 562M-90 ASME SEC II A SA-563 SA-563 Specification for Carbon and Alloy Steel Nuts ASTM A 563-94 ASME SEC II A SA-564/SA-564M SA-564/SA-564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless and Heat-Resisting Steel Bars and Shapes ASTM A 564/A 564M-92a ASME SEC II A SA-574 SA-574 Specification for Alloy Steel Socket-Head Screws ASTM A 325-80a and A 574-82 ASME SEC II A SA-577/SA-577M SA-577/SA-577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates ASTM A 577/A 577M-90 ASME SEC II A SA-578/SA-578M SA-578/SA-578M Specification for Straight-Beam Ultrasonic Examination of Plain and Clad Steel Plates for Special Applications ASTM A 578/A 578M-96 ASME SEC II A SA-587 SA-587 Specification for Electric-Resistance-Welded Low-Carbon Steel Pipe for the Chemical Industry ASTM A 587-93 ASME SEC II A SA-592/SA-592M SA-592/SA-592M Specification for High-Strength Quenched and

Tempered Low-Alloy Steel Forged Fittings and Parts for Pressure Vessels ASTM A 592/A 592M-89 (R 1994) E1 ASME SEC II A SA-609/SA-609M SA-609/SA-609M Specification for Castings, Carbon, Low-Alloy, and Martensitic Stainless Steel, Ultrasonic Examination Thereof ASTM A 609/A 609M-91 ASME SEC II A SA-612/SA-612M SA-612/SA-612M Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service ASTM A 612/A 612M-90 ASME SEC II A SA-620/SA-620M SA-620/SA-620M Specification for Steel, Sheet, Carbon, Drawing Quality, Special Killed, Cold-Rolled ASTM A 620/A 620M-96 ASME SEC II A SA-638/SA-638M SA-638/SA-638M Specification for Precipitation Hardening Iron Base Superalloy Bars, Forgings, and Forging Stock for High-Temperature Service ASTM A 638/A 638M-92 ASME SEC II A SA-645/SA-645M SA-645/SA-645M Specification for Pressure Vessel Plates, 5% Nickel Alloy Steel, Specially Heat Treated ASTM A 645/A 645M-87 ASME SEC II A SA-649/SA-649M SA-649/SA-649M Specification for Forged Steel Rolls Used for Corrugating ASTM A 649/A 649M-94a ASME SEC II A SA-660 SA-660 Specification for Centrifugally Cast Carbon Steel Pipe for High-Temperature Service ASTM A 660-91a ASME SEC II A SA-662/SA-662M SA-662/SA-662M Specification for Pressure Vessel Plates, Carbon-Manganese, for Moderate and Lower Temperature Service ASTM A 662/A 622M-93 ASME SEC II A SA-666 SA-666 Specification for Austenitic Stainless Steel, Sheet, Strip, Plate, and Flat Bar ASTM A 666-96

2006

2007-03-25 20:34

ASME SEC II A SA-667/SA-667M SA-667/SA-667M Specification for Centrifugally Cast Dual Metal (Gray and White Cast Iron) Cylinders ASTM A 667/A 667M-87 ASME SEC II A SA-671 SA-671 Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures ASTM A 671-94 ASME SEC II A SA-672 SA-672 Specification for Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures ASTM A 672-94 ASME SEC II A SA-675/SA-675M SA-675/SA-675M Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties ASTM A 675/A 675M-90a (Reapproved 1995) E1 ASME SEC II A SA-688/SA-688M SA-688/SA-688M Specification for Welded Austenitic Stainless Steel Feedwater Heater Tubes ASTM A 688/A 688M-96 ASME SEC II A SA-691 SA-691 Specification for Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High-Pressure Service at High Temperatures ASTM A 691-93 ASME SEC II A SA-693 SA-693 Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip ASTM A 693-93 ASME SEC II A SA-695 SA-695 Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, for Fluid Power Applications ASTM A 695-90b ASME SEC II A SA-696 SA-696 Specification for Steel Bars, Carbon, Hot-Wrought or Cold-Finished, Special Quality, for Pressure Piping Components ASTM A 696-90a (Reapproved 1995) E1 ASME SEC II A SA-703/SA-703M SA-703/SA-703M Specification for Steel Castings, General Requirements, for Pressure-Containing Parts ASTM A 703/A 703M-94 ASME SEC II A SA-705/SA-705M SA-705/SA-705M Specification for Age-Hardening Stainless and

Heat-Resisting Steel Forgings ASTM A 705/A 705M-93 ASME SEC II A SA-723/SA-723M SA-723/SA-723M Specification for Alloy Steel Forgings for High-Strength Pressure Component Application ASTM A 723/A 723M-94 ASME SEC II A SA-724/SA-724M SA-724/SA-724M Specification for Pressure Vessel Plates, Carbon Steel, Quenched and Tempered, for Welded Layered Pressure Vessels ASTM A 724/A 724M-90 ASME SEC II A SA-727/SA-727M SA-727/SA-727M Specification for Forgings, Carbon Steel, for Piping Components with Inherent Notch Toughness ASTM A 727/A 727M-93 ASME SEC II A SA-731/SA-731M SA-731/SA-731M Specification for Seamless, Welded Ferritic, and Martensitic Stainless Steel Pipe ASTM A 731/A 731M-91 ASME SEC II A SA-736/SA-736M SA-736/SA-736M Specification for Pressure Vessel Plates, Low-Carbon Age-Hardening Nickel-Copper-Chromium-Molybdenum-Columbium and Nickel-Copper-Manganese-Molybdenum-Columbium Alloy Steel ASTM A 736/A 736M-88 (Reapproved 1994) ASME SEC II A SA-737/SA-737M SA-737/SA-737M Specification for Pressure Vessel Plates, High-Strength, Low-Alloy Steel ASTM A 737/A 737M-87 (Reapproved 1991) ASME SEC II A SA-738/SA-738M SA-738/SA-738M Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel, for Moderate and Lower Temperature Service ASTM A 738/A 738M-90 ASME SEC II A SA-739 SA-739 Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both ASTM A 739-90a (Reapproved 1995) E1 ASME SEC II A SA-745/SA-745M SA-745/SA-745M Practice for Ultrasonic Examination of Austenitic Steel Forgings ASTM A 745/A 745M-94 ASME SEC II A SA-747/SA-747M SA-747/SA-747M Specification for Precipitation Hardening Stainless Steel Castings ASTM A 747/A 747M-93 ASME SEC II A SA-748/SA-748M SA-748/SA-748M Specification for Statically Cast Chilled White Iron-Gray Iron Dual Metal Rolls for Pressure Vessel Use ASTM A 748/A 748M-87 ASME SEC II A SA-751 SA-751 Specification for Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products ASTM A 751-95 ASME SEC II A SA-765/SA-765M SA-765/SA-765M Specification for Carbon Steel and Low-Alloy Steel Pressure Vessel Component Forgings with Mandatory Toughness Requirements ASTM A 765/A 765M-94 ASME SEC II A SA-770/SA-770M SA-770/SA-770M Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications ASTM A 770/A 770M-86 ASME SEC II A SA-781/SA-781M SA-781/SA-781M Specification for Castings, Steel and Alloy, Common Requirements, for General Industrial Use ASTM A 781/A 781M-94a ASME SEC II A SA-788 SA-788 Specification for Steel Forgings, General Requirements ASTM A 788-94 ASME SEC II A SA-789/SA-789M SA-789/SA-789M Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service ASTM A 789/A 789M-95 ASME SEC II A SA-790/SA-790M SA-790/SA-790M Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe ASTM A 790/A 790M-95 ASME SEC II A SA-803/SA-803M SA-803/SA-803M Specification for Welded Ferritic Stainless Steel Feedwater Heater Tubes A 803/A 803M-96 ASME SEC II A SA-812/SA-812M SA-812/SA-812M Specification for Steel Sheet, High-Strength, Low-Alloy, Hot-Rolled, for Welded Layered Pressure Vessels ASTM A 812/A 812M-96

ASME SEC II A SA-813/SA-813M SA-813/SA-813M Specification for Single- or Double-Welded Austenitic Stainless Steel Pipe ASTM A 813/A 813M-95 ASME SEC II A SA-814/SA-814M SA-814/SA-814M Specification for Cold-Worked Welded Austenitic Stainless Steel Pipe ASTM A 814/A 814M-96 ASME SEC II A SA-815/SA-815M SA-815/SA-815M Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic Stainless Steel Piping Fittings ASTM A 815/A 815M-96 E1 ASME SEC II A SA-832/SA-832M SA-832/SA-832M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Vanadium ASTM A 832/A 832M-95 ASME SEC II A SA-834 SA-834 Specification for Common Requirements for Iron Castings for General Industrial Use ASTM A 834-94 ASME SEC II A SA-836/SA-836M SA-836/SA-836M Specification for Forgings, Titanium-Stabilized Carbon Steel, for Glass-Lined Piping and Pressure Vessel Service ASTM A 836/A 836M-95b ASME SEC II A SA-841/SA-841M SA-841/SA-841M Specification for Steel Plates for Pressure Vessels, Produced by the Thermo-Mechanical Control Process (TMCP) ASTM A 841/A 841M-90 ASME SEC II A SA-905 SA-905 Specification for Steel Wire, Pressure Vessel Winding ASTM A 905-93 ASME SEC II A SF-568 SF-568 Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners ASTM F 568B-93a ASME SEC II A SA/CSA-G40.21 SA/CSA-G40.21 Specification for Structural Quality Steels CAN/CSA G40.21-92 ASME SEC II A SA/EN 10028-2 SA/EN 10028-2 Specification for Flat Products Made of Steels for Pressure Purposes BS EN 10028-2-1993 ASME SEC II A SA/JIS G3118 SA/JIS G3118 Specification for Carbon Steel Plates for Pressure Vessels for Intermediate and Moderate Temperature Service JIS G3118-1987 ASME SEC II B A99 1999 Addenda Summary of Changes ASME SEC II B A2000 2000 Addenda Summary of Changes ASME SEC II B A98 1998 Addenda Summary of Changes ASME SEC II B INTRODUCTION Introduction ASME SEC II B MA APP 1 Appendix 1 - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee ASME SEC II B NMA APP A Appendix A - Nonmandatory Acceptable ASTM Editions ASME SEC II B NMA APP B Appendix B - Nonmandatory Guidelines on Multiple Marking of Materials ASME SEC II B SI SI Units ASME SEC II B SB-26/SB-26M SB-26/SB-26M Specification for Aluminum-Alloy Sand Castings ASTM B 26/B 26M-97 ASME SEC II B SB-42 SB-42 Specification for Seamless Copper Pipe, Standard Sizes ASTM B 42-93 ASME SEC II B SB-43 SB-43 Specification for Seamless Red Brass Pipe, Standard Sizes ASTM B 43-94 ASME SEC II B SB-61 SB-61 Specification for Steam or Valve Bronze Castings ASTM B 61-93 ASME SEC II B SB-62 SB-62 Specification for Composition Bronze or Ounce Metal Castings ASTM B 62-93 ASME SEC II B SB-75 SB-75 Specification for Seamless Copper Tube ASTM B 75-95a ASME SEC II B SB-96 SB-96 Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels ASTM B 96-93 ASME SEC II B SB-98 SB-98 Specification for Copper-Silicon Alloy Rod, Bar, and Shapes ASTM B 98-93

ASME SEC II B SB-108 SB-108 Specification for Aluminum-Alloy Permanent Mold Castings ASTM B 108-96a ASME SEC II B SB-111 SB-111 Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock ASTM B 111-93 ASME SEC II B SB-127 SB-127 Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip ASTM B 127-93a ASME SEC II B SB-135 SB-135 Specification for Seamless Brass Tube ASTM B 135-91b ASME SEC II B SB-148 SB-148 Specification for Aluminum-Bronze Sand Castings ASTM B 148-97 ASME SEC II B SB-150 SB-150 Specification for Aluminum Bronze Rod and Bar ASTM B 150-95 ASME SEC II B SB-151 SB-151 Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) and Copper-Nickel Rod and Bar ASTM B 151-94 ASME SEC II B SB-152 SB-152 Specification for Copper Sheet, Strip, Plate, and Rolled Bar ASTM B 152-94 ASME SEC II B SB-160 SB-160 Specification for Nickel Rod and Bar ASTM B 160-93 ASME SEC II B SB-161 SB-161 Specification for Nickel Seamless Pipe and Tube ASTM B 161-93 ASME SEC II B SB-162 SB-162 Specification for Nickel Plate, Sheet, and Strip ASTM B 162-93a ASME SEC II B SB-163 SB-163 Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes ASTM B 163-97a ASME SEC II B SB-164 SB-164 Specification for Nickel-Copper Alloy Rod, Bar, and Wire ASTM B 164-93 ASME SEC II B SB-165 SB-165 Specification for Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube ASTM B 165-93 ASME SEC II B SB-166 SB-166 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06690, N06025, and N06045) and Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617) Rod, Bar, and Wire ASTM B 166-95 ASME SEC II B SB-167 SB-167 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06690, N06025, and N06045) Seamless Pipe and Tube ASTM B 167-94a ASME SEC II B SB-168 SB-168 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and N06690, N06025, and N06045) and Nickle-Chromium-Cobalt-Molybdenum Alloys (UNS N06617) Plate, Sheet, and Strip ASTM B 168-95a ASME SEC II B SB-169 SB-169 Specification for Aluminum Bronze Plate, Sheet, Strip, and Rolled Bar ASTM B 169-95 ASME SEC II B SB-171 SB-171 Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers ASTM B 171-95 ASME SEC II B SB-187 SB-187 Specification for Copper Bar, Bus Bar, Rod, and Shapes ASTM B 187-94 ASME SEC II B SB-209 SB-209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate ASTM B 209-96 ASME SEC II B SB-210 SB-210 Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes ASTM B 210-95 ASME SEC II B SB-211 SB-211 Specification for Aluminum-Alloy Bar, Rod, and Wire ASTM B 211-95a ASME SEC II B SB-221 SB-221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, and Profiles ASTM B 221-96 ASME SEC II B SB-234 SB-234 Specification for Aluminum and Aluminum Alloy-Drawn Seamless Tubes for Condensers and Heat Exchangers ASTM B 234-95

ASME SEC II B SB-241/SB-241M SB-241/SB-241M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube ASTM B 241/B 241M-96 ASME SEC II B SB-247 SB-247 Specification for Aluminum-Alloy Die and Hand Forgings ASTM B 247-95a ASME SEC II B SB-248 SB-248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar ASTM B 248-94 ASME SEC II B SB-249 SB-249 Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, and Shapes ASTM B 249-94a ASME SEC II B SB-251 SB-251 Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube ASTM B 251-93 ASME SEC II B SB-265 SB-265 Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate ASTM B 265-98 ASME SEC II B SB-271 SB-271 Specification for Copper-Base Centrifugal Castings ASTM B 271-93a ASME SEC II B SB-283 SB-283 Specification for Copper and Copper-Alloy Die Forgings (Hot Pressed) ASTM B 283-94 ASME SEC II B SB-308/SB-308M SB-308/SB-308M Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles ASTM B 308/B 308M-96 ASME SEC II B SB-315 SB-315 Specification for Seamless Copper Alloy Pipe and Tube ASTM B 315-93 ASME SEC II B SB-333 SB-333 Specification for Nickel-Molybdenum Alloy Plate, Sheet, and Strip ASTM B 333-95a ASME SEC II B SB-335 SB-335 Specification for Nickel-Molybdenum Alloy Rod ASTM B 335-95 ASME SEC II B SB-337 SB-337 Specification for Seamless and Welded Titanium and Titanium Alloy Pipe ASTM B 337-95 ASME SEC II B SB-338 SB-338 Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers ASTM B 338-98 ASME SEC II B SB-348 SB-348 Specification for Titanium and Titanium Alloy Bars and Billets ASTM B 348-98 ASME SEC II B SB-359 SB-359 Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes with Integral Fins ASTM B 359-94 ASME SEC II B SB-363 SB-363 Specification for Seamless and Welded Unalloyed Titanium and Titanium Alloy Welding Fittings ASTM B 363-95 ASME SEC II B SB-366 SB-366 Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings ASTM B 366-97a ASME SEC II B SB-367 SB-367 Specification for Titanium and Titanium Alloy Castings ASTM B 367-93 ASME SEC II B SB-369 SB-369 Specification for Copper-Nickel Alloy Castings ASTM B 369-93 ASME SEC II B SB-381 SB-381 Specification for Titanium and Titanium Alloy Forgings ASTM B 381-97 ASME SEC II B SB-395 SB-395 Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes ASTM B 395-93 ASME SEC II B SB-407 SB-407 Specification for Nickel-Iron-Chromium Alloy Seamless Pipe and Tube ASTM B 407-96 ASME SEC II B SB-408 SB-408 Specification for Nickel-Iron-Chromium Alloy Rod and Bar ASTM B 408-96 ASME SEC II B SB-409 SB-409 Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip ASTM B 409-96a

ASME SEC II B SB-423 SB-423 Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 and UNS N08221) Seamless Pipe and Tube ASTM B 423-95 ASME SEC II B SB-424 SB-424 Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNS N08825 and UNS N08221) Plate, Sheet, and Strip ASTM B 424-93 ASME SEC II B SB-425 SB-425 Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 and UNS N08221) Rod and Bar ASTM B 425-93 ASME SEC II B SB-434 SB-434 Specification for Nickel-Molybdenum-Chromium-Iron Alloy (UNS N10003) Plate, Sheet, and Strip ASTM B 434-95 ASME SEC II B SB-435 SB-435 Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip ASTM B 435-97 ASME SEC II B SB-443 SB-443 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) Plate, Sheet, and Strip ASTM B 443-93 ASME SEC II B SB-444 SB-444 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) Pipe and Tube ASTM B 444-94 ASME SEC II B SB-446 SB-446 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) Rod and Bar ASTM B 446-93 ASME SEC II B SB-462 SB-462 Specification for Forged or Rolled UNS N08020, UNS N08024, UNS N08026, and UNS N08367 Alloy Pipe Flanges, Forged Fittings, and Valves and Parts for Corrosive High-Temperature Service ASTM B 462-91 ASME SEC II B SB-463 SB-463 Specification for UNS N08020, UNS N08026, and UNS N08024 Alloy Plate, Sheet, and Strip ASTM B 463-93 ASME SEC II B SB-464 SB-464 Specification for Welded UNS N08020, UNS N08024, and UNS N08026 Alloy Pipe ASTM B 464-93 ASME SEC II B SB-466 SB-466 Specification for Seamless Copper-Nickel Pipe and Tube ASTM B 466-92a ASME SEC II B SB-467 SB-467 Specification for Welded Copper-Nickel Pipe ASTM B 467-88 ASME SEC II B SB-468 SB-468 Specification for Welded UNS N08020, N08024, and N08026 Alloy Tubes ASTM B 468-93 ASME SEC II B SB-473 SB-473 Specification for UNS N08020, UNS N08026, and UNS N08024 Nickel Alloy Bar and Wire ASTM B473-95 ASME SEC II B SB-493 SB-493 Specification for Zirconium and Zirconium Alloy Forgings ASTM B 493-83 (R1993) ASME SEC II B SA-494/SA-494M SA-494/SA-494M Specification for Castings, Nickel and Nickel Alloy ASTM A 494/A 494M-94 ASME SEC II B SB-505 SB-505 Specification for Copper-Base Alloy Continuous Castings ASTM B 505-93b ASME SEC II B SB-511 SB-511 Specification for Nickel-Iron-Chromium-Silicon Alloy Bars and Shapes ASTM B 511-93 ASME SEC II B SB-514 SB-514 Specification for Welded Nickel-Iron-Chromium Alloy Pipe ASTM B 514-95 ASME SEC II B SB-515 SB-515 Specification for Welded UNS N08120, UNS N08800, UNS N08810, and UNS N08811 Alloy Tubes ASTM B 515-95 ASME SEC II B SB-516 SB-516 Specification for Welded Nickel-Chromium-Iron Alloy (UNS N06600), UNS N06025, and UNS N06045 Tubes ASTM B 516-95

ASME SEC II B SB-517 SB-517 Specification for Welded Nickel-Chromium-Iron Alloy (UNS N06600), UNS N06025, and UNS N06045 Pipe ASTM B 517-95 ASME SEC II B SB-523 SB-523 Specification for Seamless and Welded Zirconium and Zirconium Alloy Tubes ASTM B 523-92 ASME SEC II B SB-535 SB-535 Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube ASTM B 535-94 ASME SEC II B SB-536 SB-536 Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Plate, Sheet, and Strip ASTM B 536-95 ASME SEC II B SB-543 SB-543 Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube ASTM B 543-91 ASME SEC II B SB-548 SB-548 Specification for Ultrasonic Inspection of Aluminum-Alloy Plate for Pressure Vessels ASTM B 548-90 ASME SEC II B SB-550 SB-550 Specification for Zirconium and Zirconium Alloy Bar and Wire ASTM B 550-92 ASME SEC II B SB-551 SB-551 Specification for Zirconium and Zirconium Alloy Strip, Sheet, and Plate ASTM B 551-92 ASME SEC II B SB-564 SB-564 Specification for Nickel Alloy Forgings ASTM B 564-97a ASME SEC II B SB-572 SB-572 Specification for UNS N06002, UNS N06230, UNS N12160 and UNS R30556 Rod ASTM B 572-97 ASME SEC II B SB-573 SB-573 Specification for Nickel-Molybdenum-Chromium-Iron Alloy (UNS N10003) Rod ASTM B 573-95 ASME SEC II B SB-574 SB-574 Specification for Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod ASTM B 574-97 ASME SEC II B SB-575 SB-575 Specification for Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Plate, Sheet, and Strip ASTM B 575-97 ASME SEC II B SB-581 SB-581 Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Rod ASTM B 581-93 ASME SEC II B SB-582 SB-582 Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Plate, Sheet, and Strip ASTM B 582-92 ASME SEC II B SB-584 SB-584 Specification for Copper Alloy Sand Castings for General Applications ASTM B 584-93b ASME SEC II B SB-599 SB-599 Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy (UNS N08700) Plate, Sheet, and Strip ASTM B 599-92 ASME SEC II B SB-619 SB-619 Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe ASTM B 619-97 ASME SEC II B SB-620 SB-620 Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Plate, Sheet, and Strip ASTM B 620-93 ASME SEC II B SB-621 SB-621 Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Rod ASTM B 621-95 ASME SEC II B SB-622 SB-622 Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube ASTM B 622-97

ASME SEC II B SB-625 SB-625 Specification for UNS N08904, UNS N08925, UNS N08031, UNS N08932, and UNS N08926 Plate, Sheet, and Strip ASTM B 625-93a ASME SEC II B SB-626 SB-626 Specification for Welded Nickel and Nickel-Cobalt Alloy Tube ASTM B 626-97 ASME SEC II B SB-637 SB-637 Specification for Precipitation-Hardening Nickel Alloy Bars, Forgings, and Forging Stock for High-Temperature Service ASTM B 637-93a

2006

2007-03-25 20:35

ASME SEC II B SB-649 SB-649 Specification for Ni-Fe-Cr-Mo-Cu Low-Carbon Alloy (UNS N08904) and Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloys (UNS N08925, UNS N08031, and UNS N08926) Bar and Wire ASTM B 649-93 ASME SEC II B SB-658 SB-658 Specification for Seamless and Welded Zirconium and Zirconium Alloy Pipe ASTM B 658-92 ASME SEC II B SB-668 SB-668 Specification for UNS N08028 Seamless Tubes ASTM B 668-84 ASME SEC II B SB-672 SB-672 Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy (UNS N08700) Bar and Wire ASTM B 672-95 ASME SEC II B SB-673 SB-673 Specification for UNS N08904, UNS N08925, and N08926 Welded Pipe ASTM B 673-91 ASME SEC II B SB-674 SB-674 Specification for UNS N08904, UNS N08925, and UNS N08926 Welded Tube ASTM B 674-91 ASME SEC II B SB-675 SB-675 Specification for UNS N08366 and UNS N08367 Welded Pipe ASTM B 675-90a ASME SEC II B SB-676 SB-676 Specification for UNS N08366 and UNS N08367 Welded Tube ASTM B 676-90 ASME SEC II B SB-677 SB-677 Specification for UNS N08904, and UNS N08925, and UNS N08926 Seamless Pipe and Tube ASTM B 677-91 ASME SEC II B SB-688 SB-688 Specification for Chromium-Nickel-Molybdenum-Iron (UNS N08366 and UNS N08367) Plate, Sheet, and Strip ASTM B 688-95 ASME SEC II B SB-690 SB-690 Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Seamless Pipe and Tube ASTM B 690-93 ASME SEC II B SB-691 SB-691 Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Rod, Bar, and Wire ASTM B 691-95 ASME SEC II B SB-704 SB-704 Specification for Welded UNS N06625 and UNS N08825 Alloy Tubes ASTM B 704-91 ASME SEC II B SB-705 SB-705 Specification for Nickel-Alloy (UNS N06625 and N08825) Welded Pipe ASTM B 705-94 ASME SEC II B SB-709 SB-709 Specification for Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08028) Plate, Sheet, and Strip ASTM B 709-93 ASME SEC II B SB-710 SB-710 Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe ASTM B 710-94 ASME SEC II B SB-729 SB-729 Specification for Seamless UNS N08020, UNS N08026, and UNS N08024 Nickel-Alloy Pipe and Tube ASTM B 729-95 ASME SEC II B SB-751 SB-751 Specification for General Requirements for Nickel and Nickel-Alloy

Seamless and Welded Tube ASTM B 751-90 ASME SEC II B SB-775 SB-775 Specification for General Requirements for Nickel and Nickel-Alloy Seamless and Welded Pipe ASTM B 775-90 ASME SEC II B SB-804 SB-804 Specification for UNS N08367 and UNS N08926 Welded Pipe ASTM B 804-93 ASME SEC II B SB-824 SB-824 Specification for General Requirements for Copper Alloy Castings ASTM B 824-93a ASME SEC II B SB-829 SB-829 Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube ASTM B 829-92 ASME SEC II B SB-858M SB-858M Specification for Test Method for Determination of Susceptibility to Stress Corrosion Cracking in Copper Alloys Using an Ammonia Vapor Test ASTM B858M-95 ASME SEC II C A2000 2000 Addenda Summary of Changes ASME SEC II C A99 1999 Addenda Summary of Changes ASME SEC II C A98 1998 Addenda Summary of Changes ASME SEC II C INTRODUCTION Introduction ASME SEC II C MA APP I Appendix I - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee ASME SEC II C SI SI Units ASME SEC II C SFA-5.1 SFA-5.1 Specification for Carbon Steel Electrodes for Shielded Metal Arc Welding AWS A5.1-91 ASME SEC II C SFA-5.2 SFA-5.2 Specification for Carbon and Low Alloy Steel Rods for Oxyfuel Gas Welding AWS A5.2-92 ASME SEC II C SFA-5.3 SFA-5.3 Specification for Aluminum and Aluminum-Alloy Electrodes for Shielded Metal Arc Welding AWS A5.3/A5.3M-99 ASME SEC II C SFA-5.4 SFA-5.4 Specification for Stainless Steel Electrodes for Shielded Metal Arc Welding AWS A5.4-92 ASME SEC II C SFA-5.5 SFA-5.5 Specification for Low-Alloy Steel Electrodes for Shielded Metal Arc Welding AWS A5.5-96 ASME SEC II C SFA-5.6 SFA-5.6 Specification for Covered Copper and Copper Alloy Arc Welding Electrodes AWS A5.6-84R ASME SEC II C SFA-5.7 SFA-5.7 Specification for Copper and Copper Alloy Bare Welding Rods and Electrodes AWS A5.7-84R ASME SEC II C SFA-5.8 SFA-5.8 Specification for Filler Metals for Brazing and Braze Welding AWS A5.8-92 ASME SEC II C SFA-5.9 SFA-5.9 Specification for Bare Stainless Steel Welding Electrodes and Rods AWS A5.9-93 ASME SEC II C SFA-5.10 SFA-5.10 Specification for Bare Aluminum and Aluminum Alloy Welding Electrodes and Rods AWS A5.10-92 ASME SEC II C SFA-5.11 SFA-5.11 Specification for Nickel and Nickel-Alloy Welding Electrodes for Shielded Metal Arc Welding AWS A5.11/A5.11M-97 ASME SEC II C SFA-5.12 SFA-5.12 Specification for Tungsten and Tungsten-Alloy Electrodes for Arc Welding and Cutting AWS A5.12/A5.12M-98 ASME SEC II C SFA-5.13 SFA-5.13 Specification for Solid Surfacing Welding Rods and Electrodes AWS A5.13-80

ASME SEC II C SFA-5.14 SFA-5.14 Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods AWS A5.14/A5.14M-97 ASME SEC II C SFA-5.15 SFA-5.15 Specification for Welding Electrodes and Rods for Cast Iron AWS A5.15-90 ASME SEC II C SFA-5.16 SFA-5.16 Specification for Titanium and Titanium Alloy Welding Electrodes and Rods AWS A5.16-90 ASME SEC II C SFA-5.17 SFA-5.17 Specification for Carbon Steel Electrodes and Fluxes for Submerged Arc Welding AWS A5.17/A5.17M-97 ASME SEC II C SFA-5.18 SFA-5.18 Specification for Carbon Steel Electrodes and Rods for Gas Shielded Arc Welding AWS A5.18-93 ASME SEC II C SFA-5.20 SFA-5.20 Specification for Carbon Steel Electrodes for Flux Cored Arc Welding AWS A5.20-95 ASME SEC II C SFA-5.21 SFA-5.21 Specification for Composite Surfacing Welding Rods and Electrodes AWS A5.21-80 ASME SEC II C SFA-5.22 SFA-5.22 Specification for Stainless Steel Electrodes for Flux Cored Arc Welding and Stainless Steel Flux Cored Rods for Gas Tungsten Arc Welding AWS A5.22-95 ASME SEC II C SFA-5.23 SFA-5.23 Specification for Low-Alloy Steel Electrodes and Fluxes for Submerged Arc Welding AWS A5.23/A523M-97 ASME SEC II C SFA-5.24 SFA-5.24 Specification for Zirconium and Zirconium Alloy Welding Electrodes and Rods AWS A5.24-90 ASME SEC II C SFA-5.25 SFA-5.25 Specification for Carbon and Low-Alloy Steel Electrodes and Fluxes for Electroslag Welding AWS A5.25/A5.25M-97 ASME SEC II C SFA-5.26 SFA-5.26 Specification for Carbon and Low-Alloy Steel Electrodes for Electrogas Welding AWS A5.26/A5.26M-97 ASME SEC II C SFA-5.28 SFA-5.28 Specification for Low-Alloy Steel Electrodes and Rods for Gas Shielded Arc Welding AWS A5.28-96 ASME SEC II C SFA-5.29 SFA-5.29 Specification for Low-Alloy Steel Electrodes for Flux Cored Arc Welding AWS A5.29-98 ASME SEC II C SFA-5.30 SFA-5.30 Specification for Consumable Inserts AWS A5.30-79R ASME SEC II C SFA-5.31 SFA-5.31 Specification for Fluxes for Brazing and Braze Welding AWS A5.31-92 ASME SEC II C SFA-5.01 SFA-5.01 Filler Metal Procurement Guidelines AWS A5.01-92 ASME SEC II D A2000 2000 Addenda Summary of Changes ASME SEC II D A99 1999 Addenda Summary of Changes ASME SEC II D A98 1998 Addenda Summary of Changes ASME SEC II D INTRODUCTION Introduction ASME SEC II D SB PT 1 Subpart 1 Stress Tables ASME SEC II D SB PT 2 Subpart 2 Physical Properties Tables ASME SEC II D SB PT 3 Subpart 3 Charts and Tables for Determining Shell Thickness of Components under External Pressure ASME SEC II D APPENDIX 1 Appendix 1 Basis for Establishing Stress Values in Tables 1A and 1B ASME SEC II D APPENDIX 2 Appendix 2 Basis for Establishing Design Stress Intensity Values for Tables 2A, 2B, 3, and 4 ASME SEC II D APPENDIX 3 Appendix 3 Basis for Establishing External Pressure Charts

ASME SEC II D APPENDIX 4 Appendix 4 Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee ASME SEC II D APPENDIX 5 Appendix 5 Guideline on the Approval of New Materials under the ASME Boiler and Pressure Vessel Code ASME SEC II D APPENDIX 6 Appendix 6 Metallurgical Phenomena ASME SEC II D APPENDIX 7 Appendix 7 Guidelines on Multiple Marking of Materials ASME SEC II D SI UNITS SI Units ASME SEC III NCA A99 1999 Addenda Summary of Changes ASME SEC III NCA A2000 2000 Addenda Summary of Changes ASME SEC III NCA A98 1998 Addenda Summary of Changes ASME SEC III NCA INTRODUCTION Introduction ASME SEC III NCA ORGN Organization of Section III ASME SEC III NCA ACI The American Concrete Institute ASME SEC III NCA-1000 Article NCA-1000 Scope of Section III ASME SEC III NCA-2000 Article NCA-2000 Classification of Components and Supports ASME SEC III NCA-3000 Article NCA-3000 Responsibilities and Duties ASME SEC III NCA-4000 Article NCA-4000 Quality Assurance ASME SEC III NCA-5000 Article NCA-5000 Authorized Inspection ASME SEC III NCA-8000 Article NCA-8000 Certificates, Nameplates, Code Symbol Stamping, and Data Reports ASME SEC III NCA-9000 Article NCA-9000 Glossary ASME SEC III NCA SI UNITS SI Units ASME SEC III D1 NH A2000 2000 Addenda Summary of Changes ASME SEC III D1 NB A2000 2000 Addenda Summary of Changes ASME SEC III D1 NE A2000 2000 Addenda Summary of Changes ASME SEC III D1 NG A2000 2000 Addenda Summary of Changes ASME SEC III D1 ND A2000 2000 Addenda Summary of Changes ASME SEC III D1 NF A2000 2000 Addenda Summary of Changes ASME SEC III D1 NC A2000 2000 Addenda Summary of Changes ASME SEC III D1 APP A2000 2000 Addenda Summary of Changes ASME SEC III D1 NB A99 1999 Addenda Summary of Changes ASME SEC III D1 NB A98 1998 Addenda Summary of Changes ASME SEC III D1 NB INTRO Introduction ASME SEC III D1 NB-1000 Article NB-1000 Introduction ASME SEC III D1 NB-2000 Article NB-2000 Material ASME SEC III D1 NB-3000 Article NB-3000 Design ASME SEC III D1 NB-4000 Article NB-4000 Fabrication and Installation ASME SEC III D1 NB-5000 Article NB-5000 Examination ASME SEC III D1 NB-6000 Article NB-6000 Testing ASME SEC III D1 NB-7000 Article NB-7000 Overpressure Protection ASME SEC III D1 NB-8000 Article NB-8000 Nameplates, Stamping, and Reports ASME SEC III D1 NB SI UNITS SI Units ASME SEC III D1 NC A99 1999 Addenda Summary of Changes ASME SEC III D1 NC A98 1998 Addenda Summary of Changes

ASME SEC III D1 NC INTRO Introduction ASME SEC III D1 NC-1000 Article NC-1000 Introduction ASME SEC III D1 NC-2000 Article NC-2000 Material ASME SEC III D1 NC-3000 Article NC-3000 Design ASME SEC III D1 NC-4000 Article NC-4000 Fabrication and Installation ASME SEC III D1 NC-5000 Article NC-5000 Examination ASME SEC III D1 NC-6000 Article NC-6000 Testing ASME SEC III D1 NC-7000 Article NC-7000 Overpressure Protection ASME SEC III D1 NC-8000 Article NC-8000 Nameplates, Stamping, and Reports ASME SEC III D1 NC SI UNITS SI Units ASME SEC III D1 ND A99 1999 Addenda Summary of Changes ASME SEC III D1 ND A98 1998 Addenda Summary of Changes ASME SEC III D1 ND INTRO Introduction ASME SEC III D1 ND-1000 Article ND-1000 Introduction ASME SEC III D1 ND-2000 Article ND-2000 Material ASME SEC III D1 ND-3000 Article ND-3000 Design ASME SEC III D1 ND-4000 Article ND-4000 Fabrication and Installation ASME SEC III D1 ND-5000 Article ND-5000 Examination ASME SEC III D1 ND-6000 Article ND-6000 Testing ASME SEC III D1 ND-7000 Article ND-7000 Overpressure Protection ASME SEC III D1 ND-8000 Article ND-8000 Nameplates, Stamping, and Reports ASME SEC III D1 ND SI UNITS SI Units ASME SEC III D1 NE A99 1999 Addenda Summary of Changes ASME SEC III D1 NE A98 1998 Addenda Summary of Changes ASME SEC III D1 NE INTRO Introduction ASME SEC III D1 NE-1000 Article NE-1000 Introduction ASME SEC III D1 NE-2000 Article NE-2000 Material ASME SEC III D1 NE-3000 Article NE-3000 Design ASME SEC III D1 NE-4000 Article NE-4000 Fabrication and Installation ASME SEC III D1 NE-5000 Article NE-5000 Examination ASME SEC III D1 NE-6000 Article NE-6000 Testing ASME SEC III D1 NE-7000 Article NE-7000 Overpressure Protection ASME SEC III D1 NE-8000 Article NE-8000 Nameplates, Stamping, and Reports ASME SEC III D1 NE SI UNITS SI Units ASME SEC III D1 NF A99 1999 Addenda Summary of Changes ASME SEC III D1 NF A98 1998 Addenda Summary of Changes ASME SEC III D1 NF INTRO Introduction ASME SEC III D1 NF-1000 Article NF-1000 Introduction ASME SEC III D1 NF-2000 Article NF-2000 Material ASME SEC III D1 NF-3000 Article NF-3000 Design ASME SEC III D1 NF-4000 Article NF-4000 Fabrication and Installation ASME SEC III D1 NF-5000 Article NF-5000 Examination ASME SEC III D1 NF-8000 Article NF-8000 Certificates of Authorization and Certificates of Conformance

ASME SEC III D1 MA APP NF-I Appendix NF-I (In the Course of Preparation) ASME SEC III D1 MA APP NF-II Appendix NF-II Design of Single Angle Members ASME SEC III D1 MA APP NF-III Appendix NF-III Energy Absorbing Support Material ASME SEC III D1 NMA APP NF-A Structural Bolt Preloading ASME SEC III D1 NMA APP NF-B Design Allowable Stresses for Plate-, Shell-, and Linear-Type Supports ASME SEC III D1 NF SI UNITS SI Units ASME SEC III D1 NG A99 1999 Addenda Summary of Changes ASME SEC III D1 NG A98 1998 Addenda Summary of Changes ASME SEC III D1 NG INTRO Introduction ASME SEC III D1 NG-1000 Article NG-1000 Introduction ASME SEC III D1 NG-2000 Article NG-2000 Material ASME SEC III D1 NG-3000 Article NG-3000 Design ASME SEC III D1 NG-4000 Article NG-4000 Fabrication and Installation ASME SEC III D1 NG-5000 Article NG-5000 Examination ASME SEC III D1 NG-8000 Article NG-8000 Nameplates, Stamping, and Reports ASME SEC III D1 NG SI UNITS SI Units ASME SEC III D1 NH A99 1999 Addenda Summary of Changes ASME SEC III D1 NH A98 1998 Addenda Summary of Changes ASME SEC III D1 NH INTRO Introduction ASME SEC III D1 NH-1000 Article NH-1000 Introduction ASME SEC III D1 NH-2000 Article NH-2000 Material ASME SEC III D1 NH-3000 Article NH-3000 Design ASME SEC III D1 NH-4000 Article NH-4000 Fabrication and Installation ASME SEC III D1 NH-5000 Article NH-5000 Examination ASME SEC III D1 NH-6000 Article NH-6000 Testing ASME SEC III D1 NH-7000 Article NH-7000 Overpressure Protection ASME SEC III D1 NH MA I-14 Appendix I-14 Tables I-14.0 ASME SEC III D1 NH NMA X Appendix X Guidelines for Restricted Material Specifications to Improve Performance in Certain Service Applications ASME SEC III D1 NH NMA T Appendix T Rules for Strain, Deformation, and Fatigue Limits at Elevated Temperatures ASME SEC III D1 NH SI SI Units ASME SEC III D1 APP A99 1999 Addenda Summary of Changes ASME SEC III D1 APP A98 1998 Addenda Summary of Changes ASME SEC III D1 APP INTRO Introduction ASME SEC III D1 MA APP I Appendix I Design Stress Intensity Values, Allowable Stresses, Material Properties, and Design Fatigue Curves ASME SEC III D1 MA APP II Appendix II Experimental Stress Analysis ASME SEC III D1 MA APP III Appendix III Basis for Establishing Design Stress Intensity Values and Allowable Stress Values ASME SEC III D1 MA APP IV Appendix IV Approval of New Materials under the ASME Boiler and Pressure Vessel Code ASME SEC III D1 MA APP V Appendix V Certificate Holders' Data Report Forms, Instructions, and

Application Forms for Certificates of Authorization for Use of Code Symbol Stamps ASME SEC III D1 MA APP VI Appendix VI Rounded Indications ASME SEC III D1 MA APP VII Appendix VII Charts and Tables for Determining Shell Thickness of Cylindrical and Spherical Components under External Pressure ASME SEC III D1 MA APP XI Appendix XI Rules for Bolted Flange Connections for Class 2 and 3 Components and Class MC Vessels ASME SEC III D1 MA APP XII Appendix XII Design Considerations for Bolted Flange Connections ASME SEC III D1 MA APP XIII Appendix XIII Design Based on Stress Analysis for Vessels Designed in Accordance with NC-3200 ASME SEC III D1 MA APP XIV Appendix XIV Design Based on Fatigue Analysis for Vessels Designed in Accordance with NC-3200 ASME SEC III D1 MA APP XVIII Appendix XVIII Capacity Conversions for Pressure Relief Valves ASME SEC III D1 MA APP XIX Appendix XIX Integral Flat Head with a Large Opening ASME SEC III D1 MA APP XX Appendix XX Submittal of Technical Inquiries to the Boiler and Pressure Vessel Committee ASME SEC III D1 MA APP XXI Appendix XXI Adhesive Attachment of Nameplates ASME SEC III D1 MA APP XXII Appendix XXII Design of Reinforcement for Cone-to-Cylinder Junction under External Pressure ASME SEC III D1 MA APP XXIII Appendix XXIII Qualifications and Duties of Specialized Professional Engineers ASME SEC III D1 NMA APP A Appendix A Stress Analysis Methods ASME SEC III D1 NMA APP B Appendix B Owner's Design Specifications ASME SEC III D1 NMA APP C Appendix C Certificate Holder's Design Report ASME SEC III D1 NMA APP D Appendix D Nonmandatory Preheat Procedures ASME SEC III D1 NMA APP E Appendix E Minimum Bolt Cross-Sectional Area ASME SEC III D1 NMA APP F Appendix F Rules for Evaluation of Service Loadings with Level D Service Limits ASME SEC III D1 NMA APP G Appendix G Protection Against Nonductile Failure ASME SEC III D1 NMA APP J Appendix J Owner's Design Specifications for Core Support Structures ASME SEC III D1 NMA APP K Appendix K Tolerances ASME SEC III D1 NMA APP L Appendix L Class FF Flange Design for Class 2 and 3 Components and Class MC Vessels ASME SEC III D1 NMA APP M Appendix M Recommendations for Control of Welding, Postweld Heat Treatment, and Nondestructive Examination of Welds ASME SEC III D1 NMA APP N Appendix N Dynamic Analysis Methods ASME SEC III D1 NMA APP O Appendix O Rules for Design of Safety Valve Installations ASME SEC III D1 NMA APP P Appendix P Contents of Certified Material Test Reports ASME SEC III D1 NMA APP Q Appendix Q Design Rules for Clamp Connections ASME SEC III D1 NMA APP R Appendix R Determination of Permissible Lowest Service Metal Temperature from TNDT for Classes 2 and MC Construction ASME SEC III D1 NMA APP S Appendix S Pump Shaft Design Methods ASME SEC III D1 NMA APP T Appendix T Recommended Tolerances for Reconciliation of Piping Systems ASME SEC III D1 NMA APP U Appendix U Rules for Pump Internals

ASME SEC III D1 NMA APP V Appendix V Interruption of Code Work ASME SEC III D1 NMA APP W Appendix W Environmental Effects on Components ASME SEC III D1 APP SI UNITS SI Units ASME SEC III D2 A2000 2000 Addenda Summary of Changes ASME SEC III D2 A99 1999 Addenda Summary of Changes ASME SEC III D2 A98 1998 Addenda Summary of Changes ASME SEC III D2 INTRODUCTION Introduction ASME SEC III D2 INTRO Introduction to Section III, Division 2 ASME SEC III D2 CC-1000 Article CC-1000 Introduction ASME SEC III D2 CC-2000 Article CC-2000 Material ASME SEC III D2 CC-3000 Article CC-3000 Design ASME SEC III D2 CC-4000 Article CC-4000 Fabrication and Construction ASME SEC III D2 CC-5000 Article CC-5000 Construction Testing and Examination ASME SEC III D2 CC-6000 Article CC-6000 Structural Integrity Test of Concrete Containments ASME SEC III D2 CC-7000 Article CC-7000 Overpressure Protection ASME SEC III D2 CC-8000 Article CC-8000 Nameplates, Stamping, and Reports ASME SEC III D2 MA APP I Appendix I Tables of Prestressing and Liner Material ASME SEC III D2 MA APP II Appendix II Concrete Multiaxial Compressive Strength Modification ASME SEC III D2 MA APP III Appendix III Glossary of Terms and Nomenclature ASME SEC III D2 MA APP IV Appendix IV Approval of New Material ASME SEC III D2 MA APP VI Appendix VI Rounded Indications ASME SEC III D2 MA APP VII Appendix VII Qualifications of Concrete Inspection Personnel ASME SEC III D2 MA APP IX Appendix IX Nondestructive Examination Methods ASME SEC III D2 MA APP X Appendix X Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee ASME SEC III D2 MA APP XI Appendix XI Qualifications for Arc Welding Reinforcing Bars ASME SEC III D2 NMA APP C Appendix C Typical CRV Load Combinations (Optional) ASME SEC III D2 NMA APP D Appendix D Nonmandatory Preheat Procedures ASME SEC III D2 NMA APP E Appendix E Certification of Level I and II Concrete Inspection Personnel ASME SEC III D2 NMA APP F Appendix F Liner Dimensional Tolerances ASME SEC III D2 NMA APP G Appendix G Certified Material Test Reports for Liner Materials ASME SEC III D2 NMA APP H Appendix H Reinforcement Fabrication and Placing Tolerances ASME SEC III D2 REF MTL Reference Material ASME SEC III D2 CODES Codes, Standards, and Specifications Referenced in Text ASME SEC III D2 SI UNITS SI Units ASME SEC III D3 A99 1999 Addenda Summary of Changes ASME SEC III D3 WB-8000 Article WB-8000 Nameplates, Stamping and Reports ASME SEC III D3 A2000 2000 Addenda Summary of Changes ASME SEC III D3 A98 1998 Addenda Summary of Changes ASME SEC III D3 INTRODUCTION Introduction ASME SEC III D3 WA-1000 Article WA-1000 Scope of Division 3 ASME SEC III D3 WA-2000 Article WA-2000 Design Basis for Containment Systems for Transport Packagings ASME SEC III D3 WA-3000 Article WA-3000 Responsibilities and Duties

ASME SEC III D3 WA-4000 Article WA-4000 Quality Assurance ASME SEC III D3 WA-5000 Article WA-5000 Authorized Inspection ASME SEC III D3 WA-8000 Article WA-8000 Certificates of Authorization, Nameplates, Code Symbol Stamping, and Data Reports ASME SEC III D3 WA-9000 Article WA-9000 Glossary ASME SEC III D3 WB-1000 Article WB-1000 Introduction ASME SEC III D3 WB-2000 Article WB-2000 Material ASME SEC III D3 WB-3000 Article WB-3000 Design ASME SEC III D3 WB-4000 Article WB-4000 Fabrication and Installation ASME SEC III D3 WB-5000 Article WB-5000 Examination ASME SEC III D3 WB-6000 Article WB-6000 Testing ASME SEC III D3 REF MTL Reference Material ASME SEC III D3 CODES Codes, Standards, and Specifications Referenced in Text ASME SEC III SI UNITS SI Units ASME SEC IV A99 Addenda 1999 Summary of Changes ASME SEC IV A2000 2000 Addenda Summary of Changes ASME SEC IV A98 Addenda 1998 Summary of Changes ASME SEC IV INTRODUCTION INTRODUCTION ASME SEC IV PT HG A-1 Article 1 Scope and Service Restrictions ASME SEC IV PT HG A-2 Article 2 Material Requirements ASME SEC IV PT HG A-3 Article 3 Design ASME SEC IV PT HG A-4 Article 4 Pressure Relieving Devices ASME SEC IV PT HG A-5 Article 5 Tests, Inspection, and Stamping ASME SEC IV PT HG A-6 Article 6 Instruments, Fittings, and Controls ASME SEC IV PT HG A-7 Article 7 Installation Requirements ASME SEC IV PT HF A-1 Article 1 General ASME SEC IV PT HF A-2 Article 2 Material Requirements ASME SEC IV PT HF A-3 Article 3 Design Stresses and Minimum Thicknesses ASME SEC IV PT HF-HW A-4 Article 4 General Requirements ASME SEC IV PT HF-HW A-5 Article 5 Material Requirements ASME SEC IV PT HF-HW A-6 Article 6 Welding Processes and Qualifications ASME SEC IV PT HF-HW A-7 Article 7 Design of Weldments ASME SEC IV PT HF-HW A-8 Article 8 Fabrication Requirements ASME SEC IV PT HF-HW A-9 Article 9 Inspection ASME SEC IV PT HF-HB A-10 Article 10 General Requirements ASME SEC IV PT HF-HB A-11 Article 11 Material Requirements ASME SEC IV PT HF-HB A-12 Article 12 Brazing Processes, Procedures, and Qualifications ASME SEC IV PT HF-HB A-13 Article 13 Design ASME SEC IV PT HF-HB A-14 Article 14 Fabrication Requirements ASME SEC IV PT HF-HB A-15 Article 15 Inspection and Stamping ASME SEC IV PT HC A-1 Article 1 General ASME SEC IV PT HC A-2 Article 2 Material Requirements ASME SEC IV PT HC A-3 Article 3 Design ASME SEC IV PT HC A-4 Article 4 Tests

ASME SEC IV PT HC A-5 Article 5 Quality Control and Inspection ASME SEC IV PT HLW INTRO Introduction ASME SEC IV PT HLW A-1 Article 1 General ASME SEC IV PT HLW A-2 Article 2 Material Requirements ASME SEC IV PT HLW A-3 Article 3 Design ASME SEC IV PT HLW A-4 Article 4 Design of Weldments ASME SEC IV PT HLW A-5 Article 5 Tests ASME SEC IV PT HLW A-6 Article 6 Inspection and Stamping ASME SEC IV PT HLW A-7 Article 7 Controls ASME SEC IV PT HLW A-8 Article 8 Installation Requirements ASME SEC IV MA APP 1 Appendix 1 - Mandatory Preparation of Technical Inquiries to the Boiler and Pressure Vessel Committee ASME SEC IV MA APP 2 Appendix 2 - Mandatory Codes, Standards, and Specifications Referenced in Text ASME SEC IV MA APP 3 Appendix 3 - Mandatory Adhesive Attachment of Nameplates to Casing ASME SEC IV MA APP 4 Appendix 4 - Mandatory Alternative Specification for Plates and Bars in Lieu of SA-36 for Flat Plates and Bars ASME SEC IV MA APP 5 Appendix 5 - Mandatory Vacuum Boilers ASME SEC IV NMA APP A Appendix A Approval of New Materials Under the ASME Boiler and Pressure Vessel Code ASME SEC IV NMA APP B Appendix B Method of Checking Safety Valve and Safety Relief Valve Capacity by Measuring Maximum Amount of Fuel That Can Be Burned ASME SEC IV NMA APP C Appendix C Examples of Method of Calculating a Welded Ring Reinforced Furnace ASME SEC IV NMA APP D Appendix D Examples of Methods of Computation of Openings in Boiler Shells ASME SEC IV NMA APP E Appendix E Terminology ASME SEC IV NMA APP F Appendix F Quality Control System ASME SEC IV NMA APP H Appendix H List of Abbreviations and Addresses ASME SEC IV NMA APP I Appendix I Specification for Test Method for Water Absorption of Plastics ASTM D 570-81 Reapproved 1988 ASME SEC IV NMA APP K Appendix K Guide to Information Appearing on Certificate of Authorization ASME SEC IV NMA APP L Appendix L Guide to Manufacturer's Data Report Forms ASME SEC IV SI UNITS SI Units ASME SEC IV INDEX Index ASME SEC V A2000 2000 Addenda Summary of Changes ASME SEC V A99 1999 Addenda Summary of Changes ASME SEC V A98 1998 Addenda Summary of Changes ASME SEC V INTRODUCTION Introduction ASME SEC V A-1 Article 1 General Requirements ASME SEC V A-2 Article 2 Radiographic Examination ASME SEC V A-4 Article 4 Ultrasonic Examination Methods for Inservice Inspection ASME SEC V A-5 Article 5 Ultrasonic Examination Methods for Materials and Fabrication ASME SEC V A-6 Article 6 Liquid Penetrant Examination ASME SEC V A-7 Article 7 Magnetic Particle Examination

ASME SEC V A-8 Article 8 Eddy Current Examination of Tubular Products ASME SEC V A-9 Article 9 Visual Examination ASME SEC V A-10 Article 10 Leak Testing ASME SEC V A-11 Article 11 Acoustic Emission Examination of Fiber-Reinforced Plastic Vessels ASME SEC V A-12 Article 12 Acoustic Emission Examination of Metallic Vessels During Pressure Testing ASME SEC V A-13 Article 13 Continuous Acoustic Emission Monitoring ASME SEC V B SE-94 SE-94 Standard Guide for Radiographic Testing ASTM E 94-93 ASME SEC V B SE-142 SE-142 Standard Method for Controlling Quality of Radiographic Testing ASTM E 142-92 ASME SEC V B SE-186 SE-186 Standard Reference Radiographs for Heavy-Walled [2 to 4 1/2-in. (51 to 114-mm)] Steel Castings ASTM E 186-93 ASME SEC V B SE-242 SE-242 Standard Reference Radiographs for Appearances of Radiographic as Certain Parameters Are Changed ASTM E 242-91 ASME SEC V B SE-280 SE-280 Standard Reference Radiographs for Heavy-Walled [4 1/2 to 12-in. (114 to 305-mm)] Steel Castings ASTM E 280-93 ASME SEC V B SE-446 SE-446 Standard Reference Radiographs for Steel Castings up to 2 in. (51 mm) in Thickness ASTM E 446-93 ASME SEC V B SE-747 SE-747 Standard Practice for Design, Manufacture, and Material Grouping Classification of Wire Image Quality Indicators (IQI) Used for Radiology ASTM E747-97 ASME SEC V B SE-999 SE-999 Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing ASTM E 999-95 ASME SEC V B SE-1025 SE-1025 Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiology ASTM E1025-98 ASME SEC V B SE-1030 SE-1030 Standard Test Method for Radiographic Examination of Metallic Castings ASTM E 1030-95 ASME SEC V B SE-1079 SE-1079 Standard Practice for Calibration of Transmission Densitometers ASTM E 1079-97 ASME SEC V B SE-1114 SE-1114 Standard Test Method for Determining the Focal Size of Iridium-192 Industrial Radiographic Sources ASTM E 1114-92 (R1997) ASME SEC V B SE-1165 SE-1165 Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging ASTM E 1416-96 ASME SEC V B SE-1255 SE-1255 Standard Practice for Radioscopy ASTM E 1255-96 ASME SEC V B SE-1416 SE-1416 Standard Test Method for Radioscopic Examination of Weldments ASTM E 1416-96 ASME SEC V B SE-1647 SE-1647 Standard Practice for Determining Contrast Sensitivity in Radioscopy ASTM E1647-94 ASME SEC V B SE-1815 SE-1815 Standard Test Method for Classification of Film Systems for Industrial Radiography ASTM E 1815-96 ASME SEC V B SA-388/SA-388M SA-388/SA-388M Standard Practice for Ultrasonic Examination of Heavy Steel Forgings ASTM A 388/A 388M-95 ASME SEC V B SA-435/SA-435M SA-435/SA-435M Standard Specification for Straight-Beam Ultrasonic Examination of Steel Plates ASTM A 435/A 435M-90 (1996) ASME SEC V B SA-577/SA-577M SA-577/SA-577M Standard Specification for Ultrasonic Angle-Beam

Examination of Steel Plates ASTM A 577/A 577M-90 (1996) ASME SEC V B SA-578/SA-578M SA-578/SA-578M Standard Specification for Straight-Beam Ultrasonic Examination of Plain and Clad Steel Plates for Special Applications ASTM A 578/A 578M-96 ASME SEC V B SA-609/SA-609M SA-609/SA-609M Standard Practice for Castings, Carbon, Low-Alloy, and Martensitic Stainless Steel, Ultrasonic Examination Thereof ASTM A 609/A 609M-91 (1997) ASME SEC V B SA-745/SA-745M SA-745/SA-745M Standard Practice for Ultrasonic Examination of Austenitic Steel Forgings ASTM A 745/A 745M-94 ASME SEC V B SB-509 SB-509 Specification for Supplementary Requirements for Nickel Alloy Plate for Nuclear Applications ASTM B509-77

2006

2007-03-25 20:39

ASME SEC V B SB-510 SB-510 Specification for Supplementary Requirements for Nickel Alloy Rod and Bar for Nuclear Applications ASTM B 510-77 ASME SEC V B SB-513 SB-513 Specification for Supplementary Requirements for Nickel Alloy Seamless Pipe and Tube for Nuclear Applications ASTM B 513-77 ASME SEC V B SB-548 SB-548 Standard Method for Ultrasonic Inspection of Aluminum-Alloy Plate for Pressure Vessels ASTM B548-90 ASME SEC V B SE-114 SE-114 Standard Practice for Ultrasonic Pulse-Echo Straight-Beam Examination by the Contact Method ASTM E114-95 ASME SEC V B SE-213 SE-213 Standard Practice for Ultrasonic Inspection of Metal Pipe and Tubing ASTM E213-98 ASME SEC V B SE-214 SE-214 Standard Practice for Immersed Ultrasonic Examination by the Reflection Method Using Pulsed Longitudinal Waves ASTM E214-68 (1985) ASME SEC V B SE-273 SE-273 Standard Practice for Ultrasonic Examination of Longitudinal Welded Pipe and Tubing ASTM E 273-93 ASME SEC V B SE-797 SE-797 Standard Practice for Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method ASTM E797-95 ASME SEC V B SD-129 SD-129 Standard Test Method for Sulfur in Petroleum Products (General Bomb Method) ASTM D129-95 ASME SEC V B SD-516 SD-516 Standard Test Method for Sulfate Ion in Water ASTM D 516-90 ASME SEC V B SD-808 SD-808 Standard Test Method for Chlorine in New and Used Petroleum Products (Bomb Method) ASTM D808-95 ASME SEC V B SD-1552 SD-1552 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) ASTM D 1552-95 ASME SEC V B SE-165 SE-165 Standard Test Method for Liquid Penetrant Examination ASTM E165-95 ASME SEC V B SE-1209 SE-1209 Standard Test Method for Fluorescent Penetrant Examination Using the Water-Washable Process ASTM E1209-87 ASME SEC V B SE-1219 SE-1219 Standard Test Method for Fluorescent Penetrant Examination Using the Solvent-Removable Process ASTM E 1219-87 ASME SEC V B SE-1220 SE-1220 Standard Test Method for Visible Penetrant Examination Using the Solvent-Removable Process ASTM E 1220-87 ASME SEC V B SE-709 SE-709 Standard Guide for Magnetic Particle Examination ASTM E709-95 ASME SEC V B SE-215 SE-215 Recommended Practice for Standardizing Equipment for

Electromagnetic Testing of Seamless Aluminum-Alloy Tube ASTM E 215-67 (1979)E2 ASME SEC V B SE-243 SE-243 Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes ASTM E243-97 ASME SEC V B SE-309 SE-309 Standard Practice for Examination of Steel Tubular Products Using Magnetic Saturation ASTM E309-83 ASME SEC V B SE-426 SE-426 Standard Practice for Electromagnetic (Eddy-Current) Examination of Seamless and Welded Tubular Products, Austenitic Stainless Steel, and Similar Alloys ASTM E 426-88 ASME SEC V B SE-571 SE-571 Standard Practice for Electromagnetic (Eddy-Current) Examination of Nickel and Nickel Alloy Tubular Produ

相关文章:
钢管标准及名称
X11CrMo5+1/STB340/STB35/STB41 0/STB42/STB510/STB52/STBA25/STBA23/S...套管和油管规范 ASTM A53/ASME SA53 黑色无缝钢管 ASTM A106/ ASME SA106 ...
钢管品种及相关标准基本知识
钢管品种与标准基本常识 一、钢管标准基本知识 1、标准:标准是对经济技术活动中...国际标准(ISO) 、美国标准(如: API 美国石油工业协会、ASTM 美国材料与试验...
ASTM钢管标准
ASTM 钢管标准 A1000-99 弹簧专用碳钢和合金钢钢丝规范 A1001-99 大型材高强度...耐腐蚀合金外覆或内衬钢管 API Spec 6A 井口装置和采油装置 API Spec 6AV1 ...
常用钢管规格型号一览表
常用钢管规格及用途管径应以 mm 为单位,管径的表达方式应符合下列规定: 1 水...ASTMA213/A21 3m GB5310-95 ASTMA106-99 DIN17175-79 GB3087-1999 用途 ...
钢管标准体系
钢管壁厚表示方法有管子表号、钢管壁厚尺寸和管子重量三种方法 1)是以管子表号...该标准与其它相关的 ANSI、API 、ASTM、MSS 组成的压力管道应用标准体系形 成...
美国钢管ASTM标准技术标准大全
美国钢管ASTM标准技术标准大全_冶金/矿山/地质_工程科技_专业资料。美国钢管ASTM标准技术标准大全 美国钢管 ASTM 标准技术标准大全序号 品种 标准号 标题 1 ASTM ...
astm钢管标准
astm 钢管标准更多钢管知识:www.029wfg.com A34/A34M-96 磁性材料的抽样和...(2000) 硅钙合金钢技术规范 A496-97ae1 钢筋混凝土用变形钢丝 A497-99e1 ...
直缝焊管标准要求一览表1新
° ASTM A53/53M-06 API 5L(44 版) 管子、钢、黑管和热浸镀锌管、焊管和...本标准规定了石油天然气工业管线输送系 统用 PSL1、PSL2 水平钢管制造要求。 ...
不锈钢管执行标准
1.0-1.5mm 二、工业配管用不锈钢钢管 执行标准:ASTM A312 ASTM A778 GB/T12771 材质:进口一级正材 304 304L 316 316L 规格:φ 13.72~φ 1000mm 产品...
管件标准(各国对照)
ANSI——美国国家标准化组织 ASTM.American Society of Testing Materials, ——....1 ASME/ANSI B18.2.2 API std605 无缝及焊接钢管 不锈钢无缝及焊接钢管 ...
更多相关标签:
astm钢管标准 | astma335p91合金钢管 | astm.a 53m是什么钢管 | astm标准 | astm标准下载 | astm a312标准中文版 | astm标准中文版下载 | astm d标准中文版下载 |